DIN EN 527-2-2017 Office furniture - Work tables - Part 2 Safety strength and durability requirements German version EN 527-2 2016《办公家具 工作台 第2部分 安全性、强度和耐久性要求 德文版本EN 527-2-2016》.pdf

《DIN EN 527-2-2017 Office furniture - Work tables - Part 2 Safety strength and durability requirements German version EN 527-2 2016《办公家具 工作台 第2部分 安全性、强度和耐久性要求 德文版本EN 527-2-2016》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 527-2-2017 Office furniture - Work tables - Part 2 Safety strength and durability requirements German version EN 527-2 2016《办公家具 工作台 第2部分 安全性、强度和耐久性要求 德文版本EN 527-2-2016》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、March 2017 English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 97.140!%bV“2635161www.din.deDIN EN

2、527-2Office furniture Work tables Part 2: Safety, strength and durability requirements;English version EN 5272:2016,English translation of DIN EN 527-2:2017-03Brombel BroArbeitstische Teil 2: Anforderungen an die Sicherheit, Festigkeit und Dauerhaltbarkeit;Englische Fassung EN 5272:2016,Englische be

3、rsetzung von DIN EN 527-2:2017-03Mobilier de bureau Tables de travail de bureau Partie 2: Exigences de scurit, de rsistance et de durabilit;Version anglaise EN 5272:2016,Traduction anglaise de DIN EN 527-2:2017-03SupersedesDIN EN 5272:200301 andDIN EN 5273:200306www.beuth.deDTranslation by DIN-Sprac

4、hendienst.In case of doubt, the German-language original shall be considered authoritative.Document comprises 13 pages 02.17 2 A comma is used as the decimal marker. Start of application The start of application of this standard is 2017-03-01. National foreword This document (EN 527-2:2016) has been

5、 prepared by Technical Committee CEN/TC 207 “Furniture”, (Secretariat: UNI, Italy). The responsible German body involved in its preparation was DIN-Normenausschuss Holzwirtschaft und Mbel (DIN Standards Committee Timber and Furniture), Working Committee NA 042-05-19 AA Anforde-rungen an Brombel, SpA

6、 CEN/TC 207/WG 3, ISO/TC 136/WG 1 und WG 2. This standard includes safety requirements within the meaning of the Produktsicherheitsgesetz (ProdSG) (German Product Safety Act). Where this standard has been identified by the Ausschuss fr Produktsicherheit (German Committee for Product Safety) and refe

7、rence to it has been published in the Gemeinsames Ministerialblatt (German Joint Ministerial Gazette) by the Bundesanstalt fr Arbeitsschutz und Arbeitsmedizin (BAuA) (German Federal Institute for Occupational Safety and Health), it is to be presumed that work tables which comply with this standard f

8、ulfil the relevant health and safety requirements. Amendments This standard differs from DIN EN 527-2:2003-01 and DIN EN 527-3:2003-06 as follows: a) test sequence and parameters are included, according to tests in EN 1730:2012; b) the A-deviation has been deleted. Previous editions DIN 4554: 1986-1

9、2 DIN EN 527-2: 2003-01 DIN EN 527-3: 2003-06 DIN EN 527-2:2017-03 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 527-2 December 2016 ICS 97.140 Supersedes EN 527-2:2002English Version Office furniture - Work tables - Part 2: Safety, strength and durability requirements Mobilier de bureau - Ta

10、bles de travail de bureau - Partie 2 : Exigences de scurit, de rsistance et de durabilit Brombel - Bro-Arbeitstische - Teil 2: Anforderungen an die Sicherheit, Festigkeit und Dauerhaltbarkeit This European Standard was approved by CEN on 16 October 2016. CEN members are bound to comply with the CEN/

11、CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Cent

12、re or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the

13、 official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherl

14、ands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights

15、 of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 527-2:2016 EEN 527-2:2016 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Safety requirements . 4 4.1 General 4 4.2 Shear and squeeze poin

16、ts . 5 4.2.1 Shear and squeeze points when setting up and folding 5 4.2.2 Shear and squeeze points under influence of powered mechanisms 5 4.2.3 Shear and squeeze points during use 5 4.3 Stability requirements 5 4.4 Structural safety requirements 5 5 Strength and durability . 5 5.1 General 5 Table 1

17、 Test sequence and parameters . 6 5.2 Requirements . 8 6 Information for use 8 7 Test report . 8 Annex A (informative) Test for the deflection of table tops . 9 Annex B (informative) Stiffness of the structure example 10 Figure B.1 Stiffness of the structure . 10 DIN EN 527-2:2017-03 EN 527-2:2016 (

18、E) 3 European foreword This document (EN 527-2:2016) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the

19、 latest by June 2017, and conflicting national standards shall be withdrawn at the latest by June 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent right

20、s. This document supersedes EN 527-2:2002. Compared to the previous version, modifications are: Test sequence and parameters are included, according to tests in EN 1730:2012 instead of EN 527-3:2003, which will be withdrawn; Suppression of A-deviation; Addition of an Annex B (informative) for an exa

21、mple of calculation for stiffness of the structure. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland

22、, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 527-2:2017-03 EN 527-2:2016

23、(E) 4 1 Scope This European Standard specifies safety, strength and durability requirements for work tables and desks for office tasks to be undertaken in a seated, a sit-stand or standing position. It does not apply to other tables in the office area, which are covered by EN 15372. Annex A (informa

24、tive) contains a test for the deflection of tables tops. Annex B (informative) contains an example of calculation of the stiffness of the structure. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its applicat

25、ion. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1730:2012, Furniture - Tables - Test methods for the determination of stability, strength and durability 3 Terms and definitions For

26、 the purposes of this document, the following terms and definitions apply. 3.1 accessible part part to which access can easily be gained by the user when the table is in its intended configuration of use and for which the probability of unintentional user contact is high 3.2 part accessible during s

27、etting up and folding part to which access can only be gained when setting up and folding the table 3.3 shear and squeeze point gap which can cause harm to fingers and which occurs when two accessible parts move relative to each other 3.4 overturn event at which a table pivots to a point beyond whic

28、h the table continues to fall 4 Safety requirements 4.1 General The table shall be designed so as to minimize the risk of injury to the user. All parts of the table with which the user comes into contact during intended use, shall be designed so that physical injury and damage are avoided. These req

29、uirements are fulfilled when: a) all accessible edges and corners are free from burrs and rounded or chamfered; b) the edges and corners of the top surfaces are chamfered not less than 1 mm by 1 mm or rounded with a radius of not less than 2 mm; DIN EN 527-2:2017-03 EN 527-2:2016 (E) 5 c) the ends o

30、f feet and tubular components are closed or capped. Movable and adjustable parts shall be designed so that injuries and inadvertent operation are avoided. It shall not be possible for any load bearing part of the table to come loose unintentionally. All parts which are lubricated to assist sliding s

31、hall be designed to protect users from lubricant stains when in normal use. 4.2 Shear and squeeze points 4.2.1 Shear and squeeze points when setting up and folding Unless 4.2.2 or 4.2.3 are applicable, shear and squeeze points that are created only during setting up and folding are acceptable, becau

32、se the user can be assumed to be in control of his/her movements and to be able to cease applying the force immediately upon experiencing pain. The edges of parts moving relative to each other and creating shear and squeeze points shall be as specified in 4.1. 4.2.2 Shear and squeeze points under in

33、fluence of powered mechanisms There shall be no shear and squeeze points which close to less than 25 mm unless they are always less than 7 mm created by parts of the table operated by powered mechanisms, i.e. springs, gas lifts and motorized systems. 4.2.3 Shear and squeeze points during use There s

34、hall be no shear and squeeze points which close to less than 25 mm unless they are always less than 7 mm created by forces applied during normal use or created by the user during normal movements and actions, e.g. attempting to move the table. 4.3 Stability requirements The table shall not overturn

35、when tested according to tests 10 and 11 of Table 1. 4.4 Structural safety requirements The structural safety requirements are fulfilled when the requirements according to 5.2 are fulfilled. 5 Strength and durability 5.1 General Tables shall be tested according to Table 1 and following the order lis

36、ted in Table 1. With the exception of test 9 Drop test, work tables supplied with storage features shall be tested with the following loads in the storage feature: extension elements: 0,5 kg/dm3; suspended pocket files: 4 kg/dm. DIN EN 527-2:2017-03 EN 527-2:2016 (E) 6 Table 1 Test sequence and para

37、meters Tests Reference Parameters Value Minimum mass on the table top, kg: 50c1. Durability of height adjustment mechanismsdEN 1730:2012, 8 Location of the centre of the loading point and loading on the table top: - A: 20 kg at 200 mm from the front and side edges. The remaining load shall be at the

38、 geometric centre of the table top (25 % of the cycles); - B: 50 kg or the maximum load specified shall be at the geometric centre of the table top (50 % of the cycles); - C: 20 kg positioned at a rear corner 200 mm from the rear edge and the side edge. The remaining load shall be at the geometric c

39、entre of the table top (25 % of the cycles) cycles: 5000 2.1. Horizontal static load test aEN 1730:2012, 6.2 Load on the table top, kg: Specified force, N: Minimum specified force, N: Cycles 50 450 300 10 2.2. Additional horizontal static load test for adjustable tables with a height more than 950 m

40、m bEN 1730:2012, 6.2 Load on the table top, kg: Moment, Nm: Cycles 50 285 10 3.1 Vertical static load tests aEN 1730:2012, 6.3.1 Force, N Cycles 1 000 10 3.2 Additional vertical static load test for EN 1730:2012, 6.3.1 Force, N Cycles 500 10 DIN EN 527-2:2017-03 EN 527-2:2016 (E) 7 Tests Reference P

41、arameters Value adjustable tables with a height more than 950 mm b4. Horizontal durability test aEN 1730:2012, 6.4.1, 6.4.2 Load on the table top, kg: Force, N: Cycles: 50 300 10 000 5. Stiffness of the structure aEN 1730:2012, 6.4.1 and 6.4.3 Load on the table top, kg: Force, N: 0 200 6. Vertical d

42、urability test aEN 1730:2012, 6.5 Force, N: Cycles: 400 10 000 7. Durability of tables with castors EN 1730:2012, 6.8 Load on the table top, kg: Cycles: 50 2 000 8. Vertical impact test aEN 1730:2012, 6.6 Drop height, mm : Cycles 140 10 9. Drop test aEN 1730:2012, 6.9 Nominal drop height, mm: 100 10

43、. Stability under vertical load eEN 1730:2012, 7.2 Force, N V1V2 750 750 11. Stability for work tables extension elements eEN 1730:2012, 7.3 Force, N 400 aHeight adjustable tables shall be adjusted to their maximum height or 950 mm table top height, whichever is the lower. bAdjust the work table to

44、its maximum height cEither minimum 50 kg or nominal load according to the manufacturers instruction whichever is the greater dThis test is only applicable to electrically operated height adjustment mechanisms. eThe tests of the stability Clauses 10 and 11 may be carried out additionally at the very

45、beginning as an option. DIN EN 527-2:2017-03 EN 527-2:2016 (E) 8 5.2 Requirements The strength and durability requirements are fulfilled when after testing in accordance with Table 1: a) there are no fractures of any member, joint or component; b) there are no loosening of joints intended to be rigi

46、d; c) the work table fulfils its functions after removal of the test loads; d) when tested according to Table 1, test number 5, the stiffness of the structure, both D1and D2divided by the height to the top of the table top shall be 17 mm/m. NOTE An example of calculation of D1and D2is given in Annex

47、 B (informative). 6 Information for use Information for use shall be available in the language of the country in which it will be available to the end user. It shall contain at least the following details: a) information regarding intended use; b) instruction for operating the adjusting mechanisms;

48、c) instruction for the care and maintenance of the table. 7 Test report The test report shall include at least the following information: a) reference to this European Standard (EN 527-2:2016); b) the piece of furniture tested; c) details of defects observed before testing; d) any variation from the

49、 specified temperature range; e) test results; f) name and address of the test facility; g) date of test. DIN EN 527-2:2017-03 EN 527-2:2016 (E) 9 Annex A (informative) Test for the deflection of table tops A.1 It is recommended that the test specified in A.2 should be carried out if the deflection of the main surface of the table measured in the vertical static load test (EN 1730:2012, 6.3) exceeds 1/250 of the span for wood based panels, 1/150 of