DIN EN 515-2017 Aluminium and aluminium alloys - Wrought products - Temper designations German version EN 515 2017《铝和铝合金 锻制品 回火状态标识符号 德文版本EN 515-2017》.pdf

《DIN EN 515-2017 Aluminium and aluminium alloys - Wrought products - Temper designations German version EN 515 2017《铝和铝合金 锻制品 回火状态标识符号 德文版本EN 515-2017》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 515-2017 Aluminium and aluminium alloys - Wrought products - Temper designations German version EN 515 2017《铝和铝合金 锻制品 回火状态标识符号 德文版本EN 515-2017》.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、May 2017 English price group 13No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 01.040.77; 77.120.10; 77.150.01!%eB“

2、2663188www.din.deDIN EN 515Aluminium and aluminium alloys Wrought products Temper designations;English version EN 515:2017,English translation of DIN EN 515:2017-05Aluminium und Aluminiumlegierungen Halbzeug Bezeichnungen der Werkstoffzustnde;Englische Fassung EN 515:2017,Englische bersetzung von DI

3、N EN 515:2017-05Aluminium et alliages daluminium Produits corroys Dsignation des tats mtallurgiques;Version anglaise EN 515:2017,Traduction anglaise de DIN EN 515:2017-05SupersedesDIN EN 515:199312www.beuth.deDocument comprises 27 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-

4、language original shall be considered authoritative.05.17 DIN EN 515:2017-05 2 A comma is used as the decimal marker. National foreword This document (EN 515:2017) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys” (Secretariat: AFNOR, France). The responsible Germa

5、n body involved in its preparation was DIN-Normenausschuss Nichteisenmetalle (DIN Standards Committee Nonferrous Metals), Working Committee NA 066-01-06 AA “Sheet, strip and plate”. Amendments This standard differs from DIN EN 515:1993-12 as follows: a) Clause 2 “Normative references” has been added

6、; b) in Clause 3, new definitions and sources have been included; c) in 6.1 and 7.3, the precision has been improved; d) in Clause 7, the introduction has been updated; e) a new Table 1 has been included and Table 2 has been modified; f) the content of 8.4 has been improved; g) Figure 1 has been mod

7、ified; h) in Table 3, new tempers have been included; T552, T554, T72, T72510, T72511, T74511, T7452, T7454, T7752, T7754, T7852, T7854, T7952 and T7954; i) in Table 3, new tempers have been modified; H131, T3510; j) Annex A has been updated. Previous editions DIN EN 515: 1993-12 EUROPEAN STANDARD N

8、ORME EUROPENNE EUROPISCHE NORM EN 515 March 2017 ICS 01.040.77; 77.120.10; 77.150.01 Supersedes EN 515:1993English Version Aluminium and aluminium alloys - Wrought products - Temper designations Aluminium et alliages daluminium - Produits corroys -Dsignation des tats mtallurgiques Aluminium und Alum

9、iniumlegierungen - Halbzeug - Bezeichnungen der Werkstoffzustnde This European Standard was approved by CEN on 6 February 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard

10、 without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any o

11、ther language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republi

12、c, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUR

13、OPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 515:2017 EEN 51

14、5:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Basis of codification . 6 5 Basic temper designations . 6 5.1 F as fabricated . 6 5.2 O - Annealed 6 5.3 H Strain-hardened . 6 5.4 W Solution heat-treated 7 5.5 T - Thermally treated to

15、produce stable tempers other than F, O or H (for heat-treatable alloys only) 7 6 Subdivision of O (annealed) temper designations 7 6.1 O1 High temperature annealed and slow cooled . 7 6.2 O2 Thermo-mechanically processed . 7 6.3 O3 Homogenized 7 7 Subdivision of H (strain-hardened) temper designatio

16、ns . 7 8 Subdivision of T (thermally treated to produce stable tempers other than F, O or H) temper designations . 10 8.1 First digit after T . 10 8.2 Additional digits added to designations T1 to T10 12 8.3 Assigned additional digits for stress-relieved T tempers . 12 8.3.1 Stress-relieved by stret

17、ching . 12 8.3.2 Stress-relieved by compressing 13 8.3.3 Stress-relieved by combined stretching and compressing . 13 8.3.4 Assigned additional digits for stress-relieved W tempers 13 8.4 Assigned additional digits for variations of T7 type tempers 13 8.5 Demonstration of response to heat treatment 1

18、4 8.5.1 Temper designations for producer/supplier Laboratory demonstration of response to heat treatment. 14 8.5.2 Temper designations for producer/supplier Demonstration of response to temper conversion 14 8.5.3 Temper designations for purchaser/user heat treatment . 14 9 Summary . 14 Annex A (info

19、rmative) Recommendations for further T tempers extensions 23 A.1 Numeral 1 as a second digit after T . 23 A.2 Numerals 1 and 3 to 9 as a second digit after T3, T8 or T9 . 23 A.3 Numerals 1 and 3 to 5 as a second digit after T5 or T6 23 A.4 Numeral 6 as a second digit after T5 or T6 . 23 A.5 Summary

20、of possible uses of a second digit after T . 23 Bibliography . 25 DIN EN 515:2017-05 EN 515:2017 (E) 3 European foreword This document (EN 515:2017) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard

21、 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conflicting national standards shall be withdrawn at the latest by September 2017. Attention is drawn to the possibility that some of the elements of

22、this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 515:1993. The following modifications were implemented in this new version of EN 515: Addition of Clause 2 “Normative references”; new defin

23、itions and sources in Clause 3; new precision in Subclauses 6.1, 7 and 7.3; new Table 1 and modification of Table 2; improvement of the content of Clause 8.4; modification of Figure 1; inclusion of new tempers in Table 3: T552, T554, T72, T72510, T72511, T74511, T7452, T7454, T7752, T7754, T7852, T7

24、854, T7952 and T7954; modification of new tempers in Table 3: H131, T3510; updating Annex A. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus,

25、Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the Un

26、ited Kingdom. DIN EN 515:2017-05 EN 515:2017 (E) 4 1 Scope This European Standard establishes temper designations for all forms of wrought aluminium and aluminium alloys and for continuously cast aluminium and aluminium alloys drawing stock and strip intended to be wrought. NOTE Some of these temper

27、 designations may be subject of patent or patent applications and their listing herein is not to be construed in any way as the granting of a license under such patent right. Additional temper designations, conforming to this standard, may be standardized with CEN/TC 132 and AECMA/5 provided: the te

28、mper is used or is available for use by more than one user; mechanical property limits are defined; the characteristics of the temper are significantly different from those of all other tempers which have the same sequence of basic treatments and for which designations already have been assigned for

29、 the same alloy and product; the following are also defined if characteristics other than mechanical properties are considered significant: a) test methods and limits for the characteristics; or b) the specific practices used to produce the temper. 2 Normative references Not applicable. 3 Terms and

30、definitions For the purposes of this document, the following terms and definitions apply. 3.1 temper condition of the metal produced by mechanical and/or thermal processing, typically characterized by a certain structure and specified properties SOURCE: EN 12258-1:2012, 3.6.5 3.2 hot working forming

31、 of a solid metal after preheating Note 1 to entry: Strain hardening may or may not occur during hot working. SOURCE: EN 12258-1:2012, 3.2.3 DIN EN 515:2017-05 EN 515:2017 (E) 5 3.3 cold working forming of a solid metal without preheating Note 1 to entry: Plastic deformation of metal at such tempera

32、ture and strain-rate that strain-hardening occurs. SOURCE: EN 12258-1:2012, 3.2.4 3.4 strain hardening modification of a metal structure by cold working resulting in an increase in strength and hardness with loss of ductility SOURCE: EN 12258-1:2012, 3.2.11 3.5 solution heat treatment heating an all

33、oy to a suitable temperature for sufficient time to allow one or more soluble constituents to enter into solid solution, where they are retained in a supersaturated state after quenching SOURCE: EN 12258-1:2012, 3.7.1 3.6 ageing treatment of a metal aiming at a change in its properties by precipitat

34、ion of intermetallic phases from supersaturated solid solution Note 1 to entry: Ageing can be a treatment at room temperature (natural ageing) or a thermal treatment (artificial ageing). Note 2 to entry: In North America the term “aging” is used. SOURCE: EN 12258-1:2012, 3.7.15 3.7 annealing thermal

35、 treatment to soften metal by reduction or removal of strain hardening resulting from cold working and/or by coalescing precipitates from the solid solution SOURCE: EN 12258-1:2012, 3.6.6 3.8 heat-treatable alloy alloy capable of being strengthened by suitable thermal treatment Note 1 to entry: In a

36、ddition to cold working, heat-treatable alloys are typically strengthened by precipitation hardening. SOURCE: EN 12258-1:2012, 2.2.8 DIN EN 515:2017-05 EN 515:2017 (E) 6 3.9 non heat-treatable alloy alloy which is not strengthened by thermal treatment Note 1 to entry: Non-heat-treatable alloys are o

37、nly strengthened by hot or cold working. SOURCE: EN 12258-1:2012, 2.2.9 3.10 stress relieving reduction of internal residual stresses by thermal or mechanical means SOURCE: EN 12258-1:2012, 3.2.8 4 Basis of codification 4.1 The temper designations are based on the sequences of basic treatments used

38、to produce the various tempers. Property (mechanical or physical) limits apply to individual alloy-temper-product combinations. 4.2 The temper designation follows the alloy designation; these are separated by a hyphen. 4.3 Basic temper designations consists of letters. If subdivisions of the basic t

39、empers are required, these are indicated by one or more digits following the letter of the basic temper. These digits relate to a specific sequence of basic treatments, but only those treatments or operations recognized as significantly influencing the products characteristics are indicated. Should

40、some other variation of the same sequence of basic operations be applied to the same alloy, resulting in different characteristics, then additional digits are added to the designation. 5 Basic temper designations 5.1 F as fabricated This designation applies to the products of shaping processes in wh

41、ich no special control over thermal conditions or strain hardening is applied. For this temper, there are no mechanical property limits specified. 5.2 O - Annealed This designation applies to products which are annealed to obtain the lowest strength temper. The O may be followed by a digit other tha

42、n zero1. 5.3 H Strain-hardened This designation applies to products subjected to the application of cold work after annealing (or after hot forming), or to a combination of cold work and partial annealing or stabilizing, in order to secure the specified mechanical properties. The letter H is always

43、followed by at least two digits, the first indicating the specific combination of basic operations and the second indicating the degree of strain hardening. A third digit indicates the variation of a two digits temper and it is used when mechanical properties, or others characteristics, differ from

44、those of the two digits H temper to which it is added. 1Products achieving the required annealed properties after hot forming processes may be designated as O temper. DIN EN 515:2017-05 EN 515:2017 (E) 7 5.4 W Solution heat-treated This designation describes an unstable temper. It applies only to al

45、loys which spontaneously age at room temperature after solution heat-treatment. This designation is specific only when the period of natural ageing is indicated; for example W 1/2 h. 5.5 T - Thermally treated to produce stable tempers other than F, O or H (for heat-treatable alloys only) This design

46、ation applies to products which are thermally treated, with or without supplementary strain-hardening, to produce stable tempers. The T is always followed by one or more digits indicating the specific sequence of treatments. 6 Subdivision of O (annealed) temper designations 6.1 O1 High temperature a

47、nnealed and slow cooled2This designation applies to wrought products which are thermally treated at approximately the same time and temperature required for solution heat-treatment and slow cooled to room temperature, in order to generate the correct ultrasonic response and / or provide dimensional

48、stability. It is applicable to products which are to be machined prior to solution heat treatment by the user. Mechanical property limits are not specified. 6.2 O2 Thermo-mechanically processed This designation applies to wrought products subjected to a special thermo-mechanical treatment. It is app

49、licable to products which are to be super-plastically formed prior to solution heat treatment by the user. 6.3 O3 Homogenized This designation applies to continuously cast drawing stock or strip, which are subjected to a high temperature soaking treatment to eliminate or reduce segregations, thus improving subsequent formability and or response to solution heat-treatment. 7 Subdivision of H (strain-hardened) temp