DIN EN 508-2-2009 Roofing products from metal sheet - Specification for self-supporting products of steel aluminium or stainless steel sheet - Part 2 Aluminium English version of D.pdf

《DIN EN 508-2-2009 Roofing products from metal sheet - Specification for self-supporting products of steel aluminium or stainless steel sheet - Part 2 Aluminium English version of D.pdf》由会员分享，可在线阅读，更多相关《DIN EN 508-2-2009 Roofing products from metal sheet - Specification for self-supporting products of steel aluminium or stainless steel sheet - Part 2 Aluminium English version of D.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、July 2009DEUTSCHE NORM English price group 16No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.060.20!$Xtx“1538185www

2、.din.deDDIN EN 508-2Roofing products from metal sheet Specification for self-supporting products of steel, aluminium orstainless steel sheet Part 2: AluminiumEnglish version of DIN EN 508-2:2009-07Dachdeckungsprodukte aus Metallblech Festlegungen fr selbsttragende Bedachungselemente aus Stahlblech,

3、Aluminiumblechoder nichtrostendem Stahlblech Teil 2: AluminiumEnglische Fassung DIN EN 508-2:2009-07SupersedesDIN EN 508-2:2000-12www.beuth.deDocument comprises 38 pages2 National foreword This standard has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous lay

4、ing and products for wall cladding” (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Technical Committee NA 005-02-06 AA Dacheindeckungsprodukte aus Metallblech (Sp CEN/TC 128/S

5、C 7). Amendments This standard differs from DIN EN 508-2:2000-12 as follows: a) The standard has been revised in form and substance. b) Annex A, comments and Annex D have been deleted. Previous editions DIN EN 508-2: 2000-12 DIN EN 508-2:2009-07 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 5

6、08-2 July 2008 ICS 91.060.20 Supersedes EN 508-2:2000 English Version Roofing products from metal sheet Specification for self-supporting products of steel, aluminium or stainless steel sheet Part 2: Aluminium Produits de couverture en tle mtallique Spcification pour les plaques de couverture en tle

7、 dacier, daluminium ou dacier inoxydable Partie 2: Aluminium Dachdeckungsprodukte aus Metallblech Festlegungen fr selbsttragende Bedachungselemente aus Stahlblech, Aluminiumblech oder nichtrostendem Stahlblech Teil 2: Aluminium This European Standard was approved by CEN on 30 May 2008. CEN members a

8、re bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to

9、 the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the sa

10、me status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

11、Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means res

12、erved worldwide for CEN national Members. Ref. No. EN 508-2:2008: EEN 508-2:2008 (E) 2 Contents Page Foreword4 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions, symbols and abbreviations.6 3.1 General6 3.2 Material definitions 6 3.3 Profile definitions.7 3.4 Product geometr

13、y 9 3.5 Symbols and abbreviations 12 4 Requirements.13 4.1 General13 4.2 Materials .13 4.2.1 Aluminium 13 4.2.2 Organic coatings14 4.3 Products .15 4.3.1 Mechanical resistance.15 4.3.2 Calculation and tests of mechanical resistance.15 4.3.3. Dimensions.15 4.3.4 Dimensional tolerances for the profile

14、d sheet .16 4.3.5 Safety in case of fire16 5 Test methods16 5.1 Material properties.16 5.2 Surface properties .16 5.3 Structural properties .16 6 Designation 16 7 Marking, labelling and packaging 17 7.1 Marking and labelling 17 7.2 Packaging and special ordering conditions .17 7.3 Transport, storage

15、 and handling17 Annex A (normative) Dimensional tolerances 18 A.1 Tolerances for trapezoidal sheets18 A.1.1 General18 A.1.2 Depth of profile 18 A.1.3 Depth of stiffeners .19 A.1.4 Pitch 19 A.1.5 Widths of crown and valley 20 A.1.6 Cover width 20 A.1.7 Radius of bends.21 A.1.8 Deviation from straight

16、ness .22 A.1.9 Deviation from squareness.23 A.1.10 Length .23 A.1.11 Deviation of side lap24 A.1.12 Curve radius and angles .24 A.2 Tolerances for sinusoidal profiles .25 A.3 Tolerances on tiles 25 A.3.1 General25 A.3.2 Depth of tile 26 A.3.3 Web angular displacement (Figure A.12) 27 DIN EN 508-2:20

17、09-07 EN 508-2:2008 (E) 3 A.3.4 Pitch27 A.3.5 Width of crown and valley (Figure A.14).27 A.3.6 Cover width 28 A.3.7 Radius of bends.28 A.3.8 Deviation from straightness.29 A.3.9 Deviation from squareness 29 A.3.10 Length.30 A.3.11 Contraction or bulging30 A.4 Methods for measuring profiles.31 A.4.1

18、General .31 A.4.2 Depth of profile 31 A.4.3 Depth of stiffeners.31 A.4.4 Pitch31 A.4.5 Width of crown and valley 32 A.4.6 Cover width 33 A.4.7 Radius of bends.33 A.4.8 Straightness.33 A.4.9 Squareness 33 A.4.10 Length.33 A.4.11 Side laps.33 A.4.12 Side lap ripple 33 Annex B (informative) Test method

19、s for concentrated load 35 Bibliography36 Page DIN EN 508-2:2009-07 EN 508-2:2008 (E) 4 Foreword This document (EN 508-2:2008) has been prepared by Technical Committee CEN/TC 128 “Roof covering for discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN. This Eu

20、ropean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at the latest by January 2009. Attention is drawn to the possibility that some of the e

21、lements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 508-2:2000. EN 508 Roofing products from metal sheet - Specification for self-supporting products of steel, alumin

22、ium or stainless steel sheet consists of the following parts: Part 1: Steel; Part 2: Aluminium; Part 3: Stainless steel. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium,

23、 Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 508-2:2009-07 E

24、N 508-2:2008 (E) 5 Introduction Figure 1 indicates the position of this standard in the CEN framework of standards concerning roofing products of metal. Roofing products of metal Self-supporting products Fully supported products EN 14782 Copper / Zinc EN 506 Steel EN 508-1 Aluminium EN 508-2 Stainle

25、ss steel EN 508-3 Figure 1 Framework of standards In this standard the performance of the product has been defined in terms of calculation and a number of type tests. The performance of a roof constructed with these products depends not only on the properties of the product as required by this stand

26、ard, but also on the design, construction and performance of the roof as a whole in relation to the environment and conditions of use. DIN EN 508-2:2009-07 EN 508-2:2008 (E) 6 1 Scope This part of EN 508 specifies requirements for self-supporting roofing products for discontinuous laying made from a

27、luminium sheet with or without additional organic coatings. The standard establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by man

28、ufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. The standard applies to all disco

29、ntinuously laid self-supporting external profiled sheets for roofing. These profiled roof sheets are designed to keep wind, rain and snow out of the building, and to transfer any resultant loads and infrequent maintenance loads to the structure. No requirements for supporting construction, design of

30、 roof system and execution of connections and flashings are included. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced d

31、ocument (including any amendments) applies. EN 485-4, Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products. EN 1396, Aluminium and aluminium alloys - Coil-coated sheet and strip for general applications Specifications. 3 Terms

32、and definitions, symbols and abbreviations For the purposes of this document, the following terms and definitions apply. 3.1 General 3.1.1 self-supporting product Product which will, by virtue of its material and shape, support all applied loadings (e.g. snow, wind, foot traffic), and transmit these

33、 loadings to spaced structural supports 3.2 Material definitions 3.2.1 aluminium unalloyed aluminium or aluminium 3.2.2 unalloyed aluminium metal with a minimum content of 99,0% by mass of aluminium and with content by mass of any other element within the following limits : a total content of iron a

34、nd silicon not greater than 1,0% ; DIN EN 508-2:2009-07 EN 508-2:2008 (E) 7 a content of any other element not greater than 0,10% except for copper which can have a content of up to 0,20% provided that neither the chromium nor the manganese content exceeds 0,05%. 3.2.3 aluminium alloy alloy in which

35、 aluminium predominates by mass overreach of the other elements and which is not covered by the definition of unalloyed aluminium 3.2.4 temper material conditions after a production stage, for example mechanical treatment and/or heat treatment, intended to give the material physical and/or metallurg

36、ical properties 3.2.5 organic coated aluminium sheet painted, post coated, laminated or coil coated (continuously organic coated) aluminium on one or on both sides 3.3 Profile definitions 3.3.1 trapezoidal profiled sheet self-supporting sheet which is designed to allow it to be side and end lapped,

37、the crowns of which may be rounded and, in addition, the crowns, web and valley may be stiffened NOTE See Figures 2, 3, 4 and 5. Figure 2 Part of typical trapezoidal profile Figure 3 Part of typical trapezoidal profile with rounded crowns Figure 4 Part of typical trapezoidal profile with stiffened c

38、rown and web DIN EN 508-2:2009-07 EN 508-2:2008 (E) 8 Figure 5 Part of typical trapezoidal profile with stiffened valley 3.3.2 sinusoidal profiled sheet self-supporting sheet which is designed to allow it to be side and end lapped, comprising a series of arc shaped crowns and valleys interconnected

39、with tangential webs NOTE See Figure 6. Figure 6 Part of typical sinusoidal profiled sheet. 3.3.3 standing seam and concealed fix sheet self-supporting sheet profiled in such a way that the fixings are hidden within the construction and are not exposed to the weather NOTE 1 See Figures 7 and 8. NOTE

40、 2 The profile shape is designed to allow the formation of side laps on site. NOTE 3 As these types of roof covering products are used in proprietary roofing systems, no structural requirements are given within this standard. NOTE 4 These products are normally designed by testing. Figure 7 Typical s

41、tanding seam profile DIN EN 508-2:2009-07 EN 508-2:2008 (E) 9 Figure 8 Typical concealed fix profile 3.3.4 tile profiles parts of typical tile profiled sheets that can allow the sheet to be side and/or end lapped NOTE 1 See figures 9a, 9b and 9c. NOTE 2 The tile profiles may include transverse steps

42、. NOTE 3 As these types of roof covering products are used in proprietary systems no structural requirements are given within this part of EN 508. NOTE 4 These products are normally designed by testing. Figure 9 Typical tile profiles 3.4 Product geometry NOTE The names for various parts of typical t

43、rapezoidal profiled sheets are given in Figures 10a and 10b, with additional definitions for sinusoidal profiles in Figure 11 and tile profiles in Figure 12. DIN EN 508-2:2009-07 EN 508-2:2008 (E) 10 Key 1 Cover width 7 Depth 2 Valley stiffener 8 Valley 3 Rib 9 Pitch 4 Web stiffener 10 Crown 5 Troug

44、h 11 Drainage groove 6 Web 12 Crown stiffener a) Definitions of the parts of typical trapezoidal profiled sheets DIN EN 508-2:2009-07 EN 508-2:2008 (E) 11 Key 1 Bend radius 2 End lap 3 Web angle 4 Overlap 5 Underlap 6 Side lap in principle the same on tiles b) Definitions of the parts of typical tra

45、pezoidal profiled sheets Figure 10: Definitions of the parts of typical profiled sheets DIN EN 508-2:2009-07 EN 508-2:2008 (E) 12 Key 1 Depth 2 Pitch Key 1 Height of the step 2 Length of the step 3 Number of steps 4 End lap 3.5 Symbols and abbreviations AA The symbols for aluminium sheets are the al

46、loy symbols as in 4.2.1 H Aluminium temper symbol AY Acrylic paint coating SP Polyester paint coating SP-SI Silicone-modified polyester paint coating DIN EN 508-2:2009-07 Figure 11 Definitions of the parts of typical sinusoidal profiled sheets Figure 12 Definitions of the parts of typical tile EN 50

47、8-2:2008 (E) 13 PVDF Polyvinylidenefluoride paint coating PVF(F) Polyvinylfluoride film coating SP-PA Polyamid-modified polyester paint coating PUR Polyurethane paint coating PUR-PA Polyamide-modified polyurethane paint coating AK Alkyd paint coating EP Epoxy paint coating for use within a building

48、4 Requirements 4.1 General The product shall be manufactured from materials complying with clause 4.2. NOTE 1 The supplier of the materials is responsible for carrying out the tests necessary to verify that the materials supplied to the manufacturer comply with the requirements and should provide ap

49、propriate inspection documents (according to EN 10204) on request. NOTE 2 The symbols and abbreviations to be used to designate the aluminium alloy, the type and thickness of the organic coating are those of the standards referred to in clause 2. Product testing shall be provided to a defined schedule and carried out by the manufacturer or by an approved body. A permanent quality system shall be adopted by the manufacturer1). 4.2 Materials 4.2.1 Aluminium Aluminium alloys given in Table 1 are suitable provided that t