DIN EN 502-2013 Roofing products from metal sheet - Specification for fully supported roofing products of stainless steel sheet German version EN 502 2013《金属薄板屋顶制品 全支撑不锈钢薄板屋顶制品规格 德.pdf

《DIN EN 502-2013 Roofing products from metal sheet - Specification for fully supported roofing products of stainless steel sheet German version EN 502 2013《金属薄板屋顶制品 全支撑不锈钢薄板屋顶制品规格 德.pdf》由会员分享，可在线阅读，更多相关《DIN EN 502-2013 Roofing products from metal sheet - Specification for fully supported roofing products of stainless steel sheet German version EN 502 2013《金属薄板屋顶制品 全支撑不锈钢薄板屋顶制品规格 德.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、June 2013 Translation by DIN-Sprachendienst.English price group 10No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 9

2、1.060.20; 77.140.50!%3a“2021662www.din.deDDIN EN 502Roofing products from metal sheet Specification for fully supported roofing products of stainless steelsheet;English version EN 502:2013,English translation of DIN EN 502:2013-06Dachdeckungsprodukte aus Metallblech Spezifikation fr vollflchig unter

3、sttzte Dachdeckungsprodukte aus nichtrostendemStahlblech;Englische Fassung EN 502:2013,Englische bersetzung von DIN EN 502:2013-06Produits de couverture en tle mtallique Spcification pour les produits de couverture en feuille dacier inoxydable totalementsupports;Version anglaise EN 502:2013,Traducti

4、on anglaise de DIN EN 502:2013-06SupersedesDIN EN 502:2000-01www.beuth.deDocument comprises 17 pagesIn case of doubt, the German-language original shall be considered authoritative.05.13 DIN EN 502:2013-06 2 A comma is used as the decimal marker. National foreword This document (EN 502:2013) has bee

5、n prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding” (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Wo

6、rking Committee NA 005-02-06 AA Dachdeckungsprodukte aus Metallblech (SpA zu CEN/TC 128/SC 7). Amendments This standard differs from DIN EN 502:2000-01 as follows: a) further permissible steel grades have been included; b) Table 1 and Annexes A and B have been modified; c) the standard has been edit

7、orially revised. Previous editions DIN EN 502: 2000-01 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 502 March 2013 ICS 91.060.20 Supersedes EN 502:1999English Version Roofing products from metal sheet - Specification for fully supported roofing products of stainless steel sheet Produits de c

8、ouverture en tle mtallique - Spcification pour les produits de couverture en feuille dacier inoxydable totalement supports Dachdeckungsprodukte aus Metallblech - Spezifikation fr vollflchig untersttzte Dachdeckungsprodukte aus nichtrostendem Stahlblech This European Standard was approved by CEN on 5

9、 February 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may

10、be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to

11、 the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland,

12、Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Ave

13、nue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 502:2013: EEN 502:2013 (E) 2 Contents Page Foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms, definitions, symbols and abbrevi

14、ations . 5 3.1 Terms and definitions . 5 3.2 Symbols and abbreviations 6 4 Requirements. 6 4.1 General . 6 4.2 Materials . 7 4.2.1 Grades 7 4.2.2 Chemical composition 7 4.2.3 Physical properties . 7 4.2.4 Surface finishes of stainless steel. 7 4.2.5 Hot-dip terne coated stainless steel 7 4.2.6 Tin c

15、oated stainless steel . 8 4.2.7 Organic coated stainless steel. 8 4.3 Products . 9 4.3.1 Mechanical properties 9 4.3.2 Dimensions and tolerances of flat products 9 4.3.3 Formed (prefabricated) products. 10 4.3.4 Safety in case of fire . 10 5 Sampling and test methods . 11 5.1 Flat products 11 5.2 Fo

16、rmed (prefabricated) products. 11 5.2.1 Sampling 11 5.2.2 Testing 11 6 Designation 11 7 Marking, labelling and packaging 12 7.1 Marking and labelling 12 7.2 Packaging and special ordering conditions . 12 7.3 Transport, storage and handling . 12 Annex A (informative) Physical properties 13 Annex B (i

17、nformative) A-deviations 14 Bibliography . 15 DIN EN 502:2013-06 EN 502:2013 (E) 3 Foreword This document (EN 502:2013) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding“, the secretariat of which is held by NBN. This

18、European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by September 2013. Attention is drawn to the possibility that some of

19、 the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 502:1999. In comparison to the previous edition, the following sections have been changed: Table 1, Annex A

20、and Annex B. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia

21、, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 502:2013-06 EN 502:2013 (E) 4 Introduction Figure 1 indicates the p

22、osition of this standard in the CEN framework of standards concerning roofing products of metal. Roofing products of metal Self supporting products Fully supported products Zinc EN 501 Stainless steel EN 502 Copper EN 504 Steel EN 505 Aluminium EN 507 References regarding Materials Quality assurance

23、 Figure 1 Framework of standards In this European Standard, the performance of the product has been defined in terms of a number of type tests. The performance of a roof constructed with these products depends not only on the properties of the product as it is required by this standard, but also on

24、the design, construction and performance of the roof in relation to the environment and conditions of use. DIN EN 502:2013-06 EN 502:2013 (E) 5 1 Scope This European Standard specifies requirements for roofing products used for assembly into coverings for pitched roofs, made from stainless steel, te

25、rne coated, tin coated or organic coated stainless steel sheet. The European Standard establishes general characteristics, definitions and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufac

26、turers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. Products can be prefabricated or semi

27、formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam roofs, roll cap). The European Standard applies to all discontinuously laid and fully supported roofing products made of stainless steel sheet. No requirements for application (e.g. methods of fixing

28、, supporting construction, design of roof system, execution of connections and flashings) are included. NOTE The standard deals partly with flat products, partly with formed (prefabricated) products. Requirements for preformed self-supporting roofing products are given in EN 508-3. 2 Normative refer

29、ences The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. E

30、N 10079:2007, Definition of steel products EN 10088-1, Stainless steels Part 1: List of stainless steels EN 10088-4, Stainless steels Part 4 : Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes EN 10202, Cold reduced tinmill products Elect

31、rolytic tinplate and electrolytic chromium/chromium oxide coated steel EN 10204, Metallic products Types of inspection documents EN ISO 7438, Metallic materials Bend test (ISO 7438) EN ISO 9445-2, Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 2: Wide strip and plate

32、/sheet (ISO 9445-2) 3 Terms, definitions, symbols and abbreviations 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10079:2007 and the following apply. 3.1.1 stainless steel steel with at least a content of 10,5 % chromium and maximum 1,2 % carbon N

33、ote 1 to entry: For roofing products the stainless steels grades are: ferritic, DIN EN 502:2013-06 EN 502:2013 (E) 6 austenitic with or without molybdenum; austenitic-ferritic (duplex), and; higher alloyed grades. 3.1.2 terne coated stainless steel stainless steel continuously hot-dip coated with a

34、lead-tin alloy 3.1.3 tin coated stainless steel stainless steel continuously coated with tin by electrodeposition 3.1.4 organic coated stainless steel stainless steel or terne coated stainless steel or tin coated stainless steel which is continuously (factory) painted by roller or spray process Note

35、 1 to entry: EN 10169 refers to this type of coated steel. 3.1.5 fully supported installation conditions such, that the bottom flat portions of the product are supported by a continuous construction 3.2 Symbols and abbreviations The symbols and abbreviations which shall be used for the designation o

36、f the steel grades and where applicable of coatings are listed in the respective material standards mentioned in Clause 2. 4 Requirements 4.1 General The product shall be manufactured from materials complying with 4.2. The supplier of the materials is responsible for carrying out the tests necessary

37、 to verify that the materials supplied to the manufacturer comply with the requirements and should provide appropriate inspection documents (according to EN 10204) on request. NOTE The symbols and abbreviations that are used to designate the steel grade, the type and mass of the metallic coating are

38、 those of the standards referred to in EN 10027-1. A permanent quality control system shall be adopted by the manufacturer.1)1) For example, a Quality Management System based on EN ISO 9000. DIN EN 502:2013-06 EN 502:2013 (E) 7 4.2 Materials 4.2.1 Grades The grades of stainless steel shall be select

39、ed depending on the corrosion conditions of the local environment, durability requirements and aesthetic considerations. NOTE The most commonly used grades are listed in Table 1. Table 1 Grades Steel grade Steel designation Steel name Steel number Ferritic with organic coating X6Cr13 1.4000 Ferritic

40、 with or without organic coating X6Cr17 1.4016 X6CrMo17-1 1.4113 X3CrTi17 1.4510 X2CrTiNb18 1.4509 X6CrMoNb17-1 1.4526 X2CrMoTi18-2 1.4521 Austenitic with or without organic coating X5CrNi18-10 1.4301 X2CrNi18-9 1.4307 Austenitic/Molybdenum with or without organic coating X5CrNiMo17-12-2 1.4401 4.2.

41、2 Chemical composition The chemical compositions of stainless steel shall be in accordance with EN 10088-4. 4.2.3 Physical properties The physical properties for stainless steel shall be in accordance with EN 10088-1. NOTE Some physical properties are given, for information, in Annex A. 4.2.4 Surfac

42、e finishes of stainless steel All normal stainless steel finishes can be used including bright finish, 2B in accordance with EN 10088-4, dull finish, 2D in accordance with EN 10088-4 or other low reflective finishes. 4.2.5 Hot-dip terne coated stainless steel 4.2.5.1 Coating For the coating properti

43、es, one should refer to the existing national standards or to an agreement between the parties. The minimum tin content of the alloy shall be 8 % by mass. DIN EN 502:2013-06 EN 502:2013 (E) 8 4.2.5.2 Coating mass The nominal coating mass shall be the total mass of both surfaces expressed in g/m. The

44、 nominal coating mass shall be 20 g/m. The minimum values of the coating mass shall be respectively 20 g/m and 15 g/m when determined by a triple spot test or a single spot test. 4.2.6 Tin coated stainless steel 4.2.6.1 Coating The coating shall be homogeneous and shall not present any discontinuiti

45、es which could impair the use of the product. After a bend test carried out in accordance with EN ISO 7438 with a bend angle of 180 and a diameter of the mandrel equal to 1t (t thickness of the product), there shall be no peeling of the coating. 4.2.6.2 Coating mass The nominal coating mass shall be

46、 the total mass of both surfaces expressed g/m. The nominal coating mass shall be 10 g/m. The minimum values of the coating mass shall be respectively 10 g/m and 8 g/m when determined by a triple spot test or a single spot test. 4.2.7 Organic coated stainless steel The main organic coatings suitable

47、 for application to stainless steel substrates are given in Table 2. NOTE Further information is given in EN 10169. Organic coatings shall be selected dependent upon the processing and service conditions, including specific climatic conditions. Table 2 Organic coatings and specified minimum thicknes

48、ses Coating Symbol Number of layers per side a Minimum permitted nominal coating thickness in m per side Polyester SP 2 25 Silicone-modified polyester SP-SI 2 25 Polyurethane PUR 2 25 Polyvinylidene fluoride PVDF 2, 3, 4 25 Polyvinyl chloride (Plastisol) PVC(P) 2 80 aIncluding primer but excluding p

49、rotective films. DIN EN 502:2013-06 EN 502:2013 (E) 9 4.3 Products 4.3.1 Mechanical properties Mechanical properties shall be in accordance with EN 10088-4. The minimum values for relevant mechanical properties at 20 C for test pieces with a gauge length of 80 mm and a width of 20 mm shall be as given in Table 3. Table 3 Relevant mechanical properties Grade Yield strength Rp0,2 MPa min. Tensile strength Rm MPa min. Elongation A80 % min. Ferritic 250 400 19 Austenitic 230 450 40 Austenitic/molybdenum 2