DIN EN 1817-2010 Resilient floor coverings - Specification for homogeneous and heterogeneous smooth rubber floor coverings German version EN 1817 2010《地板弹性铺覆物 均质和非均质平面地板弹性铺覆物规范 德文版.pdf

《DIN EN 1817-2010 Resilient floor coverings - Specification for homogeneous and heterogeneous smooth rubber floor coverings German version EN 1817 2010《地板弹性铺覆物 均质和非均质平面地板弹性铺覆物规范 德文版.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1817-2010 Resilient floor coverings - Specification for homogeneous and heterogeneous smooth rubber floor coverings German version EN 1817 2010《地板弹性铺覆物 均质和非均质平面地板弹性铺覆物规范 德文版.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、November 2010 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 97.150!$l1y“1731486www.din.deDDIN EN 1817Resilient floor coverings Specification for homogeneous and heterogeneous smooth rubber floorcoveringsEnglish translation of DIN EN 1817:2010-11Elastische Bodenbelge Spezifikation fr homogene und heterogene ebene Elastomer-BodenbelgeEnglische bersetzung von

3、 DIN EN 1817:2010-11Revtements de sol rsilients Spcifications des revtements de sol homognes et htrognes en caoutchouc lisseTraduction anglaise de DIN EN 1817:2010-11SupersedesDIN EN 1817:1998-05www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered au

4、thoritative.1111.10 DIN EN 1817:2010-11 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” (Secretariat: BSI, United Kingdom). The responsible German body involved in its prepa

5、ration was the Normenausschuss Kunststoffe (Plastics Standards Committee), Working Committee NA 054-04-05 AA Bodenbelge. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 4649 DIN ISO 4649 Amendments This standard differs from DIN EN 1817

6、:1998-05 as follows: a) a contents list has been added; b) normative references have been updated; c) the property “cigarette resistance” has been transferred from Table 1 into Annex A (informative); d) in Table 2 “Classification requirements”, class 22+ has been added; e) the standard has been edit

7、orially revised. Previous editions DIN EN 1817: 1998-05 National Annex NA (informative) Bibliography DIN ISO 4649, Rubber, vulcanized or thermoplastic Determination of abrasion resistance using a rotating cylindrical drum device EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1817 June 2010 ICS

8、 97.150 Supersedes EN 1817:1998English Version Resilient floor coverings - Specification for homogeneous and heterogeneous smooth rubber floor coverings Revtements de sol rsilients - Spcifications des revtements de sol homognes et htrognes en caoutchouc lisse Elastische Bodenbelge - Spezifikation fr

9、 homogene und This European Standard was approved by CEN on 20 May 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliogra

10、phical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a

11、 CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland

12、, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Ma

13、rnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1817:2010: Eheterogene ebene Elastomer-Bodenbelge EN 1817:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44

14、 General requirements 55 Classification requirements 66 Marking .6Annex A (informative) Optional properties .8Bibliography 9DIN EN 1817:2010-11 EN 1817:2010 (E) 3 Foreword This document (EN 1817:2010) has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor covering

15、s”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn at the latest by December 2010. At

16、tention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1817:1998. According to the CEN/CENELEC Internal Regulations

17、, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Ne

18、therlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 1817:2010-11 EN 1817:2010 (E) 4 1 Scope This European Standard specifies the characteristics of homogeneous and heterogeneous smooth (including grained or embossed) rubber floo

19、r coverings, supplied in either tile or roll form. This European Standard includes a classification system based on intensity of use, which shows where these resilient floor coverings should give satisfactory service (see EN 685). It also specifies requirements for marking. 2 Normative references Th

20、e following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 425, Resilient and laminate floor coverings Cast

21、or chair test EN 426, Resilient floor coverings Determination of width, length, straightness and flatness of sheet material EN 427, Resilient floor coverings Determination of the side length, squareness and straightness of tiles EN 428, Resilient floor coverings Determination of overall thickness EN

22、 429, Resilient floor coverings Determination of the thickness of layers EN 433, Resilient floor coverings Determination of residual indentation after static loading EN 434, Resilient floor coverings Determination of dimensional stability and curling after exposure to heat EN 435, Resilient floor co

23、verings Determination of flexibility EN 685, Resilient, textile and laminate floor coverings Classification EN 12466:1998, Resilient floor coverings Vocabulary EN ISO 105-B02:1999, Textiles - Tests for colour fastness Part B02: Colour fastness to artificial light: Xenon arc fading lamp test (ISO 105

24、-BO2:1994, including amendment 1:1998) ISO 4649:2002, Rubber, vulcanized or thermoplastic Determination of abrasion resistance using a rotating cylindrical drum device ISO 7619:2004 (all parts), Rubber, vulcanized or thermoplastic Determination of indentation hardness 3 Terms and definitions For the

25、 purposes of this document, the terms and definitions given in EN 12466:1998 and the following apply. 3.1 homogeneous rubber floor covering floor covering based on natural or synthetic rubber with one or more layers of the same composition and colour, patterned throughout its thickness DIN EN 1817:2

26、010-11 EN 1817:2010 (E) 5 3.2 heterogeneous rubber floor covering floor covering based on natural or synthetic rubber consisting of a wear layer and other compact layers which differ in composition and/or design and can contain a reinforcement 4 General requirements All homogeneous and heterogeneous

27、 smooth rubber floor coverings shall conform to the appropriate general requirements specified in Table 1, when tested in accordance with the test methods given therein. Table 1 General requirements Property Requirements Test method Thickness See Table 2 EN 428 Roll form: length width not less than

28、the stated nominal values EN 426 Tiles: side length squareness and straightness for side of length: 610 mm 610 mm tolerance allowed: 0,15 % of nominal length tolerance allowed: 0,25 mm 0,35 mm EN 427 Dimensional stability: tolerance allowed: 0,4 % EN 434 Flexibility: diameter of mandrel 20 mm no cra

29、cking EN 435 Method A Hardness 75 Shore A ISO 7619:2004 Residual indentation (after static loading): nominal thickness 2,5 mm 2,5 mm average value 0,15 mm average value 0,20 mm EN 433 Abrasion resistance 250 mm3ISO 4649:2002 Method A, vertical load (5 0,1) N Colour fastness to artificial light a 6 m

30、inimum on blue wool scale 3 on grey scale EN ISO 105-B02:1999 Method 3 aExpose a full size test specimen. Store a further test specimen in the dark, which will constitute the reference standard for assessment of colour change. DIN EN 1817:2010-11 EN 1817:2010 (E) 6 5 Classification requirements All

31、the homogeneous and heterogeneous smooth rubber floor coverings shall be classified in accordance with the requirements for overall thickness and the wear layer thickness specified in Table 2, when tested in accordance with the test methods given therein. Table 2 Classification requirements Class (s

32、ee EN 685) Level of use Minimum overall thickness a(homogeneous and heterogeneous) mm Minimum thickness of wear layer b (heterogeneous) mm Effect of a castor chair 21 domestic moderate 1,8 1,0 No requirement 22 domestic general/medium 1,8 1,0 22+ domestic general 2,0 1,0 23 domestic heavy 2,0 1,0 31

33、 commercial moderate 2,0 1,0 32 commercial general 2,0 1,0 33 commercial heavy 2,0 1,0 34 commercial very heavy 2,0 1,0 41 light industrial moderate 2,0 1,0 If tested for verification, no disturbance to the surface other than slight change due to flatter appearance no delamination shall occur 42 lig

34、ht industrial general 2,0 1,0 43 light industrial heavy 2,5 1,0 Test method EN 428 EN 429 EN 425 aThe average overall thickness shall have a tolerance of 0,15 mm and no individual result shall exceed 0,20 mm from the nominal. bThe average thickness of the wear layer shall have a tolerance of 0,15 mm

35、 and no individual result shall exceed 0,20 mm from the nominal. 6 Marking The floor coverings described in this standard and/or their packaging shall bear the following marking: a) a reference to this European Standard, i.e. EN 1817:2010; b) the manufacturers or suppliers identification; c) the pro

36、duct name; d) the colour/pattern, and batch and roll number if applicable; DIN EN 1817:2010-11 EN 1817:2010 (E) 7 e) the class/symbol, as specified in EN 685; f) the dimensions for tiles; g) the covered area for rolls. DIN EN 1817:2010-11 EN 1817:2010 (E) 8 Annex A (informative) Optional properties

37、The following properties are considered important for some specific uses: electrical resistance (EN 1081); electrostatic propensity (EN 1815); effect of stains (EN 423); effect of simulated movement of a furniture leg (EN 424); cigarette resistance (see EN 1399). In general use, a rubber floor cover

38、ing, depending on the colour and/or pattern, is expected to have the following rating when tested in accordance with EN 1399: Method A, stubbed cigarettes; rating 4 or higher Method B, burning cigarettes; rating 3 or higher DIN EN 1817:2010-11 EN 1817:2010 (E) 9 Bibliography 1 EN 423, Resilient floo

39、r coverings - Determination of resistance to staining 2 EN 424, Resilient floor coverings - Determination of the effect of simulated movement of a furniture leg 3 EN 1081, Resilient floor coverings - Determination of the electrical resistance 4 EN 1815, Resilient and textile floor coverings - Assessment of static electrical propensity 5 EN 1399, Resilient floor coverings Determination of resistance to stubbed and burning cigarettes DIN EN 1817:2010-11