DIN EN 1816-2010 Resilient floor coverings - Specification for homogeneous and heterogeneous smooth rubber floor coverings with foam backing German version EN 1816 2010《弹性地板铺覆物 带有背.pdf

《DIN EN 1816-2010 Resilient floor coverings - Specification for homogeneous and heterogeneous smooth rubber floor coverings with foam backing German version EN 1816 2010《弹性地板铺覆物 带有背.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1816-2010 Resilient floor coverings - Specification for homogeneous and heterogeneous smooth rubber floor coverings with foam backing German version EN 1816 2010《弹性地板铺覆物 带有背.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、November 2010 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 97.150!$l1w“1731484www.din.deDDIN EN 1816Resilient floor coverings Specification for homogeneous and heterogeneous smooth rubber floorcoverings with foam backingEnglish translation of DIN EN 1816:2010-11Elastische Bodenbelge Spezifikation fr homogene und heterogene ebene Elastomer-Bodenbelge mitSc

3、haumstoffbeschichtungEnglische bersetzung von DIN EN 1816:2010-11Revtements de sol rsilients Spcifications des revtements de sol homognes et htrognes en caoutchouc lisseavec semelle en mousseTraduction anglaise de DIN EN 1816:2010-11SupersedesDIN EN 1816:1998-05www.beuth.deDocument comprises pagesIn

4、 case of doubt, the German-language original shall be considered authoritative.1011.10 DIN EN 1816:2010-11 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” (Secretariat: BSI,

5、 United Kingdom). The responsible German body involved in its preparation was the Normenausschuss Kunststoffe (Plastics Standards Committee), Working Committee NA 054-04-05 AA Bodenbelge. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO

6、4649 DIN ISO 4649 Amendments This standard differs from DIN EN 1816:1998-05 as follows: a) a contents list has been added; b) normative references have been updated; c) in Table 1 “General requirements”, column “Property”, a new line “Tiles” has been included; d) the property “cigarette resistance”

7、has been transferred from Table 1 into Annex A (informative); e) in Table 2 “Classification requirements”, class 22+ has been added; f) the standard has been editorially revised. Previous editions DIN EN 1816: 1998-05 National Annex NA (informative) Bibliography DIN ISO 4649, Rubber, vulcanized or t

8、hermoplastic Determination of abrasion resistance using a rotating cylindrical drum device EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1816 June 2010 ICS 97.150 Supersedes EN 1816:1998English Version Resilient floor coverings - Specification for homogeneous and heterogeneous smooth rubber f

9、loor coverings with foam backingRevtements de sol rsilients - Spcifications des revtements de sol homognes et htrognes en caoutchouc lisse avec semelle en mousse Elastische Bodenbelge - Spezifikation fr homogene und heterogene ebene Elastomer-Bodenbelge mit Schaumstoffbeschichtung This European Stan

10、dard was approved by CEN on 20 May 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning suc

11、h national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own languag

12、e and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithua

13、nia, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CE

14、N All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1816:2010: EEN 1816:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 General requirements 55 Classification requirements 66 Marking .6Anne

15、x A (informative) Optional properties .7Bibliography 8DIN EN 1816:2010-11 EN 1816:2010 (E) 3 Foreword This document (EN 1816:2010) has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate coverings”, the secretariat of which is held by BSI. This European Standard shall be

16、 given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn at the latest by December 2010. Attention is drawn to the possibility that some of the elements of this docume

17、nt may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1816:1998. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound

18、to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swe

19、den, Switzerland and the United Kingdom. DIN EN 1816:2010-11 EN 1816:2010 (E) 4 1 Scope This European Standard specifies the characteristics of homogeneous and heterogeneous smooth (including grained or embossed) rubber floor coverings with foam backing, supplied in roll or in tile form. This Europe

20、an Standard includes a classification system based on intensity of use, which shows where these resilient floor coverings should give satisfactory service (see EN 685). It also specifies requirements for marking. 2 Normative references The following referenced documents are indispensable for the app

21、lication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 425, Resilient and laminate floor coverings Castor chair test EN 426, Resilient floor coverings Determination

22、of width, length, straightness and flatness of sheet material EN 427, Resilient floor coverings Determination of the side length, squareness and straightness of tiles EN 428, Resilient floor coverings Determination of overall thickness EN 429, Resilient floor coverings Determination of the thickness

23、 of layers EN 431, Resilient floor coverings Determination of peel resistance EN 433, Resilient floor coverings Determination of residual indentation after static loading EN 434, Resilient floor coverings Determination of dimensional stability and curling after exposure to heat EN 435, Resilient flo

24、or coverings Determination of flexibility EN 685, Resilient floor coverings Classification EN 12466:1998, Resilient floor coverings Vocabulary EN ISO 105-B02:1999, Textiles Tests for colour fastness Part B02: Colour fastness to artificial light: Xenon arc fading lamp test (ISO 105-B02:1994, includin

25、g amendment 1:1998) ISO 4649:2002, Rubber, vulcanized or thermoplastic Determination of abrasion resistance using a rotating cylindrical drum device ISO 7619:2004 (all parts), Rubber, vulcanized or thermoplastic Determination of indentation hardness 3 Terms and definitions For the purposes of this d

26、ocument, the terms and definitions given in EN 12466:1998 and the following apply. 3.1 homogeneous rubber floor covering floor covering based on natural or synthetic rubber with one or more layers of the same composition and colour, patterned throughout its thickness DIN EN 1816:2010-11 EN 1816:2010

27、 (E) 5 3.2 heterogeneous rubber floor covering floor covering based on natural or synthetic rubber consisting of a wear layer and other compact layers which differ in composition and/or design and can contain a reinforcement 4 General requirements All homogeneous and heterogeneous smooth rubber floo

28、r coverings with foam backing shall conform to the appropriate general requirements specified in Table 1, when tested in accordance with the test methods given therein. Table 1 General requirements Property Requirements Test method Roll form: length width not less than the stated nominal values EN 4

29、26 Tiles: side length squareness and straightness for side of length: 610 mm 610 mm tolerance allowed: 0,15 % of nominal length tolerance allowed: 0,25 mm 0,35 mm EN 427 Dimensional stability tolerance allowed 0,4 % EN 434 Thickness of foam backing not less than the stated nominal value EN 429 Flexi

30、bility: diameter of mandrel 20 mm no cracking EN 435 Method A Hardness of wear layer 75 Shore A ISO 7619:2004 Residual indentation (after static loading) average value 0,25 mm EN 433 Peel resistance average value 50 N/50 mm or rupture in the foam EN 431 Abrasion resistance of wear layer 250 mm3ISO 4

31、649:2002 Method A, vertical load (5 0,1) N Colour fastness to artificial lighta 6 minimum on blue wool scale 3 on grey scale EN ISO 105-B02:1999 Method 3 aExpose a full size test specimen. Store a further test specimen in the dark, which will constitute the reference standard for assessment of colou

32、r change. DIN EN 1816:2010-11 EN 1816:2010 (E) 6 5 Classification requirements All the homogeneous and heterogeneous smooth rubber floor coverings with foam backing shall be classified in accordance with the requirements for overall thickness and the wear layer thickness specified in Table 2, when t

33、ested in accordance with the test methods given therein. Table 2 Classification requirements Class (see EN 685) Level of use Minimum overall thicknessa (homogeneous and heterogeneous) mm Minimum thickness of wear layerb(heterogeneous) mm Effect of a castor chair21 domestic moderate 2,5 1,0 No requir

34、ement 22 domestic general/medium 2,5 1,0 22+ domestic general 2,5 1,0 23 domestic heavy 3,5 1,031 commercial moderate 3,5 1,0 32 commercial general 3,5 1,0 If tested for verification, no disturbance to the surface other than slight change due to flatter appearance no delamination shall occur 33 comm

35、ercial heavy 3,5 1,0Test method EN 428 EN 429 EN 425 aThe average overall thickness shall have a tolerance of 0,20 mm and no individual result shall exceed 0,25 mm from the nominal. bThe average thickness of the wear layer shall have a tolerance of 0,20 mm and no individual result shall exceed 0,25

36、mm from the nominal. 6 Marking The floor coverings described in this standard and/or their packaging shall bear the following marking: a) reference to this European Standard, i.e. EN 1816:2010; b) manufacturers or suppliers identification; c) product name; d) colour/pattern, and batch and roll numbe

37、r if applicable; e) class/symbol, as specified in EN 685; f) covered area for rolls. DIN EN 1816:2010-11 EN 1816:2010 (E) 7 Annex A (informative) Optional properties The following properties are considered important for some specific uses: electrostatic propensity (EN 1815); effect of stains (EN 423

38、); effect of simulated movement of a furniture leg (EN 424); cigarette resistance (see EN 1399). In general use, a rubber floor covering, depending on the colour and/or pattern, is expected to have the following rating when tested in accordance with EN 1399. Method A. stubbed cigarettes; rating 4 or

39、 higher Method B, burning cigarettes; rating 3 or higher DIN EN 1816:2010-11 EN 1816:2010 (E) 8 Bibliography 1 EN 423, Resilient floor coverings Determination of the resistance to staining 2 EN 424, Resilient floor coverings Determination of the effect of simulated movement of a furniture leg 3 EN 1815, Resilient and textile floor coverings Assessment of static electrical propensity 4 EN 1399, Resilient floor coverings Determination of resistance to stubbed and burning cigarettes DIN EN 1816:2010-11