DIN EN 15372-2017 Furniture - Strength durability and safety - Requirements for non-domestic tables German version EN 15372 2016《家具 强度、耐久性和安全性 非家用桌子的要求 德文版本EN 15372-2016》.pdf

《DIN EN 15372-2017 Furniture - Strength durability and safety - Requirements for non-domestic tables German version EN 15372 2016《家具 强度、耐久性和安全性 非家用桌子的要求 德文版本EN 15372-2016》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 15372-2017 Furniture - Strength durability and safety - Requirements for non-domestic tables German version EN 15372 2016《家具 强度、耐久性和安全性 非家用桌子的要求 德文版本EN 15372-2016》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、February 2017 English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 97.140!%anz“2627587www.din.deDIN

2、 EN 15372Furniture Strength, durability and safety Requirements for nondomestic tables;English version EN 15372:2016,English translation of DIN EN 15372:2017-02Mbel Festigkeit, Dauerhaltbarkeit und Sicherheit Anforderungen an Tische fr den NichtWohnbereich;Englische Fassung EN 15372:2016,Englische b

3、ersetzung von DIN EN 15372:2017-02Ameublement Rsistance, durabilit et scurit Exigences applicables aux tables usage non domestique;Version anglaise EN 15372:2016,Traduction anglaise de DIN EN 15372:2017-02SupersedesDIN EN 15372:200806www.beuth.deDTranslation by DIN-Sprachendienst.In case of doubt, t

4、he German-language original shall be considered authoritative.Document comprises 13 pages 02.17 2 A comma is used as the decimal marker. Start of application The start of application of this standard is 2017-02-01. National foreword This document (EN 15372:2016) has been prepared by Technical Commit

5、tee CEN/TC 207 “Furniture” (Secretariat: UNI, Italy). The responsible German body involved in its preparation was DIN-Normenausschuss Holzwirtschaft und Mbel (DIN Standards Committee Timber and Furniture), Working Committee NA 042-05-15 AA Sitzmbel, Polstermbel und Tische. This standard includes saf

6、ety requirements within the meaning of the Produktsicherheitsgesetz (ProdSG) (German Product Safety Act). Where this standard has been identified by the Ausschuss fr Produktsicherheit (German Committee for Product Safety) and reference to it has been published in the Gemeinsames Ministerialblatt (Ge

7、rman Joint Ministerial Gazette) by the Bundesanstalt fr Arbeitsschutz und Arbeitsmedizin (BAuA) (German Federal Institute for Occupational Safety and Health), it is to be presumed that non-domestic tables which comply with this standard fulfil the relevant health and safety requirements. Amendments

8、This standard differs from DIN EN 15372:2008-06 as follows: a) the document has been aligned with EN 1730:2012; b) normative references have been updated; c) Annex A (informative) Additional test requirements has been added; d) Annex B (informative) Test severity in relation to application has been

9、added. Previous editions DIN EN 15372: 2008-06 DIN EN 15372:2017-02 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15372 November 2016 ICS 97.140 Supersedes EN 15372:2008English Version Furniture - Strength, durability and safety - Requirements for non-domestic tables Ameublement - Rsistance,

10、durabilit et scurit - Exigences applicables aux tables usage non domestique Mbel - Festigkeit, Dauerhaltbarkeit und Sicherheit - Anforderungen an Tische fr den Nicht-WohnbereichThis European Standard was approved by CEN on 2 October 2016. CEN members are bound to comply with the CEN/CENELEC Internal

11、 Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

12、 member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versio

13、ns. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Po

14、land, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation

15、 in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15372:2016 EEN 15372:2016 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Test conditions . 4 5 Safety, stability, strength and durability 5 5.1 General r

16、equirements . 5 5.2 Shear and squeeze points . 5 5.2.1 Shear and squeeze points when setting up and folding 5 5.2.2 Shear and squeeze points under influence of powered mechanisms 5 5.2.3 Shear and squeeze points during use 5 5.3 Stability . 5 5.3.1 Stability under vertical load 5 5.3.2 Stability for

17、 tables with extension elements . 6 5.4 Strength and durability . 6 5.4.1 General 6 5.4.2 Requirements . 8 6 Information for use 8 7 Test report . 9 Annex A (informative) Additional test requirements 10 A.1 General . 10 A.2 Deflection of table tops test 10 A.3 Durability of tables with castors. 10 A

18、.3.1 General . 10 A.3.2 Suggested requirements 10 Annex B (informative) Test severity in relation to application . 11 DIN EN 15372:2017-02 EN 15372:2016 (E) 3 European foreword This document (EN 15372:2016) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is

19、held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2017, and conflicting national standards shall be withdrawn at the latest by May 2017. Attention is drawn to the possibility that s

20、ome of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 15372:2008. The main changes in the document are to reference the revised standard EN 1730:2012. According to the CEN

21、-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungar

22、y, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 15372:2017-02 EN 15372:2016 (E) 4 1 Scope This European Standard specifies requirements for the safe

23、ty, strength and durability of all types of non-domestic tables including those with glass in their construction. It does not apply to office work tables or desks, tables for educational institutions and outdoor tables for which EN standards exist. With exception of the stability tests, this standar

24、d does not provide assessment of the suitability of any storage features included in non-domestic tables. It does not include requirements for the durability of castors and height adjustment mechanisms. It does not include requirements for electrical safety. It does not include requirements for the

25、resistance to ageing, degradation. The standard has two annexes: Annex A (informative) Additional test requirements. Annex B (informative) Test severity in relation to application. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and ar

26、e indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1730:2012, Furniture - Tables - Test methods for the determination of stability, strength and durabi

27、lity EN 12150-1:2015, Glass in building - Thermally toughened soda lime silicate safety glass - Part 1: Definition and description EN 12600:2002, Glass in building - Pendulum test - Impact test method and classification for flat glass 3 Terms and definitions For the purposes of this document, the fo

28、llowing terms and definitions apply. 3.1 accessible part part to which access can easily be gained by the user when the table is in its intended configuration of use and for which the probability of unintentional user contact is high 3.2 part accessible during setting up and folding part to which ac

29、cess can only be gained when setting up and folding the table 3.3 shear and squeeze point shear and squeeze points exist if the distance between two accessible parts moving relative to each other is less than 18 mm or more than 7 mm in any position during movement 4 Test conditions General test cond

30、itions shall be in accordance with EN 1730:2012, Clause 4. The tests shall be carried out in the order in which they are listed in Table 2. DIN EN 15372:2017-02 EN 15372:2016 (E)5 5 Safety, stability, strength and durability 5.1 General requirements The table shall be designed so as to minimize the

31、risk of injury to the user. All parts of the table with which the user comes into contact during intended use, shall be designed so that physical injury and damage are avoided. This requirement is met when: a) edges of table tops which are directly in contact with the user are rounded or chamfered;

32、b) all other edges accessible during intended use are free from burrs and/or sharp edges; c) ends of hollow components with a diameter greater than 7 mm and less than 12 mm where the accessible depth is greater than 10 mm, are closed or capped. Movable and adjustable parts shall be designed so that

33、injuries and inadvertent operation are avoided. It shall not be possible for any load bearing part of the table to come loose unintentionally. All parts which are lubricated to assist sliding shall be designed to protect users from lubricant stains when in normal use. 5.2 Shear and squeeze points 5.

34、2.1 Shear and squeeze points when setting up and folding Unless 5.2.2 or 5.2.3 are applicable, shear and squeeze points that are created only during setting up and folding are acceptable, because the user can be assumed to be in control of his/her movements and to be able to cease applying the force

35、 immediately upon experiencing pain. The edges of parts moving relative to each other and creating shear and squeeze points shall be as specified in 5.1. 5.2.2 Shear and squeeze points under influence of powered mechanisms There shall be no shear and squeeze points created by parts of the table oper

36、ated by powered mechanisms, i.e. springs, gas lifts and motorised systems. 5.2.3 Shear and squeeze points during use There shall be no shear and squeeze points created by forces applied during normal use. The loads used for durability tests within Table 2 are considered representative of normal use.

37、 There shall be no shear and squeeze points if a hazard is created by the user during normal movements and actions. 5.3 Stability 5.3.1 Stability under vertical load 5.3.1.1 General When assessing the stability of a table, reference shall be made to EN 1730:2012, 7.1. Tables that can be set to heigh

38、ts both above and below 950 mm shall be tested to both 5.3.1.2 and 5.3.1.3. DIN EN 15372:2017-02EN 15372:2016 (E) 6 5.3.1.2 Test for tables that are or can be set to a height 950 mm The table shall be set to the height most likely to cause overturning, but not more than 950 mm. The table shall not o

39、verturn when tested according to EN 1730:2012, 7.2.2, using the forces specified within Table 2. 5.3.1.3 Test for tables that are or can be set to a height 950 mm The table shall be set to the height most likely to cause overturning, but not less than 950 mm. The table shall not overturn when tested

40、 according to EN 1730:2012, 7.2.3, using 50 % of the forces specified within Table 2. 5.3.2 Stability for tables with extension elements Load each extension element with the load specified in Table 1. The table shall not overturn when tested according to EN 1730:2012, 7.3, using the forces specified

41、 within Table 2. Table 1 Loads in extension elements Component Load Extension elements designed for suspended filing only 4,0 kg/dm Other extension elements 0,5 kg/dm35.4 Strength and durability 5.4.1 General Tables shall be tested for strength and durability according to, and in the order given in

42、Table 2. The guidance for selecting test severity 1, 2 or 3 with due respect for the end use of the product is given in Annex B. Type 1 tables have a main surface 600 mm or more above the floor surface and a surface area greater than 0,3 m2. All other tables are considered as Type 2. Table 2 Stabili

43、ty, strength and durability tests Test Severity Test Reference Loading 1 2 3 1. Horizontal static load test EN 1730:2012, Test force F14, N: 6.2 Type 1 400 400 600 Type 2 200 200 300 minimum force Type 1 and Type 2 100 100 100 Specified mass, kg Manufacturers specified load or 50 kg Manufacturers sp

44、ecified load or 50 kg Manufacturers specified load or 50 kg Cycles 10 10 10 DIN EN 15372:2017-02 EN 15372:2016 (E) 7 Test Severity Test Reference Loading 1 2 3 2. Vertical static EN 1730:2012, Test force, N 1 000 1 250 1 250 load on main surfacea6.3.1 Cycles 10 10 10 3. Additional EN 1730:2012, Test

45、 force, N - 1 000 1 000 vertical static load test where the main surface has a length 1 600 mm 6.3.2 Cycles - 10 10 4. Vertical static EN 1730:2012, Test force, N 200 300 300 load on ancillary surface 6.3.3 Cycles 10 10 10 5. Horizontal durability test EN 1730:2012, 6.4.1 and 6.4.2 Test force Fa-d,

46、N 300 300 300 Specified mass, kg Manufacturers specified load or 50 kg Manufacturers specified load or 50 kg Manufacturers specified load or 50 kg Cycles: 10 000 15 000 20 000 6. Vertical durability EN 1730:2012, Test force, N 300 300 300 test for cantilever and tables with central column onlyb6.5 N

47、umber of cycles: 10 000 15 000 20 000 7. Vertical impact EN 1730:2012, Drop height, mm: test for glass tabletops 6.6.1, and 6.6.2 Safety glassc140 180 180 Other glass 180 240 240 Cycles 10 10 10 8. Vertical impact EN 1730:2012, Drop height, mm: 140 180 180 test for all other tabletops 6.6.1 and 6.6.

48、3 Cycles 10 10 10 DIN EN 15372:2017-02 EN 15372:2016 (E) 8 Test Severity Test Reference Loading 1 2 3 9. Drop test This test is applicable for tables weighing EN 1730:2012, 6.9 Nominal drop height mm tables without glass 100 100 100 more than 20 kg only Nominal drop height mm tables with glass 50 50

49、 50 10. Stability under vertical load test EN 1730:2012, 7.2 Test force, N Main surface V1V2Ancillary surface V1V2200 400 100 200 200 400 100 200 200 400 100 200 11. Stability for tables withextension elements EN 1730:2012, 7.3 Test force, N 200 200 200 aTables with extension pieces shall be tested both in the extended and unextended configurations. A table extension added in the centre of the table shall be tested as the main surface. A part of the main