DIN EN 15348-2015 Plastics - Recycled plastics - Characterization of poly(ethylene terephthalate) (PET) recyclates German version EN 15348 2014《塑料 再生塑料 聚对苯二甲酸乙二酯(PET)再生塑料的特性 德文版本EN.pdf

《DIN EN 15348-2015 Plastics - Recycled plastics - Characterization of poly(ethylene terephthalate) (PET) recyclates German version EN 15348 2014《塑料 再生塑料 聚对苯二甲酸乙二酯(PET)再生塑料的特性 德文版本EN.pdf》由会员分享，可在线阅读，更多相关《DIN EN 15348-2015 Plastics - Recycled plastics - Characterization of poly(ethylene terephthalate) (PET) recyclates German version EN 15348 2014《塑料 再生塑料 聚对苯二甲酸乙二酯(PET)再生塑料的特性 德文版本EN.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、January 2015 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 13.030.50; 83.080.20!%?0“2281358www.din.deDDIN EN 15348Plastics Recycled plastics Characterization of poly(ethylene terephthalate) (PET) recyclates;English version EN 15348:2014,English translation of DIN EN 15348:2015-01Kunststoffe Kunststoff-Rezyklate Charakterisierung von Polyethylenterephthala

3、t (PET)-Rezyklaten;Englische Fassung EN 15348:2014,Englische bersetzung von DIN EN 15348:2015-01Plastiques Plastiques recycls Caractrisation des recyclats de poly(thylne trphtalate) (PET);Version anglaise EN 15348:2014,Traduction anglaise de DIN EN 15348:2015-01SupersedesDIN EN 15348:2008-02www.beut

4、h.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 21 pages 01.15 DIN EN 15348:2015-01 2 A comma is used as the decimal marker. National foreword This document (EN 15348:2014) has been prepared by Technical Committee CEN/TC 249 “Plastics” (Secreta

5、riat: NBN, Belgium). The responsible German body involved in its preparation was the DIN-Normenausschuss Kunststoffe (DIN Standards Committee Plastics), Working Committee NA 054-01-06 AA Kunststoffverwertung. The DIN Standard corresponding to the International Standard referred to in this document i

6、s as follows: ISO 565 DIN ISO 565 Amendments This standard differs from DIN EN 15348:2008-02 as follows: a) the former Annex B (informative) “Method for the determination of the melt mass-flow rate (MFR) of PET” has been deleted, reference is now made to EN ISO 1133-2; b) all subsequent annexes have

7、 been relettered; c) in the former Annex C, now Annex B (normative) “Gravimetric method for the determination of residual humidity (water content)”, the crucible of platinum has been replaced by a crucible of porcelain. Previous editions DIN EN 15348: 2008-02 National Annex NA (informative) Bibliogr

8、aphy DIN ISO 565, Test sieves Metal wire cloth, perforated metal plate and electroformed sheet Nominal sizes of openings EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15348 November 2014 ICS 13.030.50; 83.080.20 Supersedes EN 15348:2007English Version Plastics - Recycled plastics - Characteri

9、zation of poly(ethylene terephthalate) (PET) recyclates Plastiques - Plastiques recycls - Caractrisation des recyclats de poly(thylne trphtalate) (PET) Kunststoffe - Kunststoff-Rezyklate - Charakterisierung von Polyethylenterephthalat (PET)-Rezyklaten This European Standard was approved by CEN on 20

10、 September 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may

11、 be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified t

12、o the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland,

13、 Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Managemen

14、t Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15348:2014 EEN 15348:2014 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5

15、 4 Characterization of PET recyclates6 5 Quality assurance 7 Annex A (normative) Determination of size and distribution of PET-R flakes by sieving .8 Annex B (normative) Gravimetric method for the determination of residual humidity (water content) 11 Annex C (normative) Rapid method for the determin

16、ation of residual impurities . 13 Annex D (informative) Potentiometric method for the determination of the residual alkalinity. 15 Annex E (informative) Method for the determination of infusible impurities by filtration 17 Bibliography . 19 DIN EN 15348:2015-01 EN 15348:2014 (E) 3 Foreword This docu

17、ment (EN 15348:2014) has been prepared by Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2015 and conflicti

18、ng national standards shall be withdrawn at the latest by May 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supe

19、rsedes EN 15348:2007. EN 15348:2014 includes the following significant technical changes with respect to EN 15348:2007: a) the deletion of former informative Annex B and replacement by a reference to EN ISO 1133-2 in Table 1; b) the use of a porcelain crucible instead of a crucible of platinum in B.

20、5. This European Standard is one part of a series of CEN publications on Plastics Recycling which is structured as follows: EN 15342, Plastics Recycled Plastics Characterization of polystyrene (PS) recyclates EN 15343, Plastics Recycled Plastics Plastics recycling traceability and assessment of conf

21、ormity and recycled content EN 15344, Plastics Recycled Plastics Characterization of Polyethylene (PE) recyclates EN 15345, Plastics Recycled Plastics Characterization of Polypropylene (PP) recyclates EN 15346, Plastics Recycled plastics Characterization of poly(vinyl chloride) (PVC) recyclates EN 1

22、5347, Plastics Recycled Plastics Characterization of plastics wastes EN 15348, Plastics Recycled plastics Characterization of poly(ethylene terephthalate) (PET) recyclates CEN/TR 15353, Plastics Recycled plastics Guidelines for the development of standards for recycled plastics According to the CEN-

23、CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary

24、, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 15348:2015-01 EN 15348:2014(E)4 Introduction Recycling of plastics waste is one type of material reco

25、very process intended to save resources (virgin raw materials, water, and energy), while minimizing harmful emissions into air, water and soil as well as any impacts on human health. The environmental impact of recycling has to be assessed over the whole life cycle of the recycling system (from the

26、waste generation point to the disposal of final residues). To ensure that recycling constitutes the best environmental option for treating the available waste, some prerequisites should preferably be met: recycling scheme being contemplated should generate lower environmental impacts than alternativ

27、e recovery options; existing or potential market outlets should be identified that will secure a sustainable industrial recycling operation; collection and sorting schemes should be properly designed to deliver recyclable plastics waste fractions fitting reasonably well with the available recycling

28、technologies and with the (changing) needs of the identified market outlets, preferably at minimum costs to society. This European Standard has been produced in accordance with the guidance produced by CEN on Environmental Aspects and in accordance with CEN/TR 15353. NOTE CEN/TR 15353 considers the

29、general environmental aspects which are specific to the recycling process. It is often impossible to trace back each individual product at the end user stage and to check whether the product has been used correctly through its life. Consequently products are out of industrial control for a period of

30、 time. It is possible that during this period contamination with other materials might occur that could affect the products suitability for recycling into the intended application. DIN EN 15348:2015-01 EN 15348:2014(E)5 1 Scope This European Standard defines a method of specifying delivery condition

31、s for poly(ethylene terephthalate) (PET) recyclates. It gives the most important characteristics and associated test methods for assessing PET recyclates intended to be used for the production of semi-finished/finished products. It is intended for use by the supplier and purchaser of such materials,

32、 to assist them in agreeing on specifications. This European Standard is applicable without prejudice to any existing legislation. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated ref

33、erences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. CEN/TR 15353, Plastics Recycled plastics Guidelines for the development of standards for recycled plastics EN ISO 472, Plastics Vocabulary (ISO 472) EN I

34、SO 1133-2, Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2) EN ISO 11664-4, Colorimetry Part 4: CIE 1976 L*a*b* Colour space (ISO 11664-4) EN ISO 1

35、5512, Plastics Determination of water content (ISO 15512) ISO 565, Test sieves Metal wire cloth, perforated metal plate and electroformed sheet Nominal sizes of openings ISO 1628-5, Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 5: Thermoplast

36、ic polyester (TP) homopolymers and copolymers ISO 3534-2, Statistics Vocabulary and symbols Part 2: Applied statistics 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 472 and CEN/TR 15353 and the following apply. 3.1 sieve retention percentage-of

37、the recycled test sample retained on a sieve at the end of the test Note 1 to entry: The sieve retention is expressed in percent (mass fraction). 3.2 container retention percentage of recycled matter retained in the container at the bottom of a stack of sieves, or under a single sieve, at the end of

38、 the test compared to the mass of the sample DINEN 15348:2015-01EN 15348:2014 (E) 6 3.3 average particulate dimension single value of size, representing the dominant particle size for the whole test sample 4 Characterization of PET recyclates A single batch is the quantity of recyclate that has homo

39、genous characteristics within the specified tolerances. The characteristics of PET recyclates, which shall be met for every batch (see ISO 3534-2) of PET recyclate are shown in Table 1, and are divided into two types: required characteristics needed to characterize PET recyclates in general and requ

40、ired for all recyclates; optional characteristics needed to characterize PET recyclates according to customer specifications and applications. These characteristics shall be assessed by using the test methods given in Table 1 and detailed below. A Certificate of Analysis, providing the test results

41、for each batch of recyclate shall be provided by the supplier to the purchaser upon request. The supplier shall provide the necessary information about the material composition of the recyclates, as specified by the purchaser or required by the applicable regulations. DIN EN 15348:2015-01 EN 15348:2

42、014(E)7 Table 1 Characterization of PET recyclates Characteristics Unit Test method Comments Required Shape Visual Flakes, pellets Maximum particle size mm Given by the size of the screen of the grinder Fine particle content % Annex A Value in percentage of the particles passing the sieve of 1 mm. C

43、olour Visual inspection Unicolour, tranparent, mixed Water content % Annex B or EN ISO 15512 PVC content mg/kg Annex C Polyolefin content mg/kg Annex C Optional Determination Melt Mass-Flow Rate (MFR) EN ISO 1133-2 Intrinsic viscosity (I.V.) dl/g ISO 1628-5 Alkalinity pH Annex D Filterability MPa/(h

44、 cm)Annex E Other residual content mg/kg Analysis according to the appropriate method e.g. FTIR, XRF, DSC Colour L,a,b values Colourimeter according to EN ISO 11664-4 Injection molded disks from Flakes, pellets Other tests may be carried out by agreement between the purchaser and the supplier and re

45、sults reported. 5 Quality assurance In order that the purchaser of the recyclate can have confidence in the quality of the product, the supplier shall maintain records of the quality control carried out, including incoming materials, processes and finished products. NOTE A quality management system

46、certified to EN ISO 9001 may be a suitable guarantee of consistent recyclate quality but not the recycled content. The specification and the standard deviation or range of values within and between batches of material shall be agreed between the supplier and the purchaser. Where a statement of recyc

47、led content, or the previous history of the material, is requested, documentary evidence shall be provided. These records should be available to the purchaser on request. Where a recyclate has been produced via a melt process, the supplier may choose to state the level of filtration applied during t

48、hat process. This will determine the maximum size of any non-melting contaminants present in the recyclate. The statement of filtration level shall include details of the filter. Recyclates that have not passed through a melt process cannot be quantified in the same way, and the supplier may state this. DINEN 15348:2015-01EN 15348:2014(E)8 Annex A (normative) Determination of size and distribution of PET-R flakes by sieving A.1 General T