DIN EN 1506-2007 Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-section - Dimensions English version of DIN EN 1506 2007-09《建筑物通风 圆形截面薄板制通风管道和异型.pdf

《DIN EN 1506-2007 Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-section - Dimensions English version of DIN EN 1506 2007-09《建筑物通风 圆形截面薄板制通风管道和异型.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1506-2007 Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-section - Dimensions English version of DIN EN 1506 2007-09《建筑物通风 圆形截面薄板制通风管道和异型.pdf（23页珍藏版）》请在麦多课文档分享上搜索。

1、September 2007DEUTSCHE NORM English price group 12No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.140.30!$I16“13814

2、19www.din.deDDIN EN 1506Ventilation for buildings Sheet metal air ducts and fittings with circular cross-section DimensionsEnglish version of DIN EN 1506:2007-09Lftung von Gebuden Luftleitungen und Formstcke aus Blech mit rundem Querschnitt MaeEnglische Fassung DIN EN 1506:2007-09SupersedesDIN EN 15

3、06:1998-02www.beuth.deDocument comprises 23 pages 11.07DIN EN 1506:2007-09 2 National foreword This standard has been prepared by Technical Committee CEN/TC 156 “Ventilation for buildings”, the Secretariat of which is held by BSI (United Kingdom). The responsible German body involved in its preparat

4、ion was the Normenausschuss Heiz- und Raumluft-technik (Heating and Ventilation Technology Standards Committee). Amendments This standard differs from DIN EN 1506:1998-02 as follows: a) This standard has been brought in line with the state of the art and has been prepared under a mandate. Previous e

5、ditions DIN 24145: 1975-10, 1992-12 DIN 24147-1: 1982-05, 1993-06 DIN 24147-2: 1982-05, 1993-06 DIN 24147-3: 1982-05, 1993-06 DIN 24147-4: 1982-05, 1993-06 DIN 24147-5: 1982-05 DIN 24147-6: 1982-05, 1993-06 DIN 24147-7: 1982-05, 1993-06 DIN 24147-8: 1982-05, 1993-06 DIN 24147-9: 1982-05 DIN 24147-10

6、: 1982-05 DIN 24147-11: 1982-05 DIN 24147-12: 1982-05 DIN 24147-13: 1982-05, 1993-06 DIN 24151: 1966-07 DIN 24151-1: 1990-04 DIN 24151-2: 1990-04 DIN 24152: 1966x-07, 1988-12, 1990-04 DIN 24153: 1966-07 DIN EN 1506: 1998-02 EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1506June 2007ICS 91.140.30

7、 Supersedes EN 1506:1997 English VersionVentilation for buildings - Sheet metal air ducts and fittings withcircular cross-section - DimensionsVentilation des btiments - Conduits en tle et accessoires section circulaire - DimensionsLftung von Gebuden - Luftleitungen und Formstcke ausBlech mit rundem

8、Querschnitt - MaeThis European Standard was approved by CEN on 24 May 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliogr

9、aphical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a C

10、EN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Ita

11、ly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 B

12、russels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1506:2007: EEN 1506:2007 (E) 2 Contents Page Foreword. 3 Introduction 4 1 Scope 6 2 Normative references . 6 3 Terms, definitions and symbols 6 4 Dimensions and values for

13、ducts 7 5 Dimensions for fittings. 8 5.1 General. 8 5.2 Joints 8 5.3 Bends . 9 5.4 Branches and T-pieces. 10 5.4.5 Transformation pieces 13 5.4.6 Closures. 14 6 Tolerances and clearances 15 Annex A (informative) Examples of alternative designs of ends and connectors 18 Bibliography . 21 EN 1506:2007

14、 (E) 3 Foreword This document (EN 1506:2007) has been prepared by Technical Committee CEN/TC 156 “Ventilation for buildings”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement

15、, at the latest by December 2007, and conflicting national standards shall be withdrawn at the latest by December 2007. This document supersedes EN 1506:1997. This standard is one of a series of standards for ductwork used for ventilation and air conditioning of buildings for human occupancy, and it

16、 has a parallel standard referring to dimensions of rectangular ducts. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estoni

17、a, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 1506:2007 (E) 4 The position of this standard in the field of mechanical

18、building services is shown in Figure 1. Mechanical Building Services Control systems Ventilation and air conditioning Heating systems systems Air handling units Ductwork Installation Circular sheet metal ducts Dimensions Circular sheet metal ducts Strength and leakage Rectangular sheet metal ducts S

19、trength and leakage Hangers and supports Rectangular sheet metal ducts. Dimensions Measurement of duct surface area Requirements for ductwork components to facilitate maintenance Flanges Identification Flexible ducts Determination of mechanical energy loss Ductwork made of insulation ductboards Figu

20、re 1 Position of EN 1506 in the field of mechanical building servicesIntroduction EN 1506:2007 (E) 5 Introduction This revised standard has been prepared by CEN/TC 156 to specify standardized dimensions and tolerances for ducts and duct fittings with circular cross-section, used in ventilation syste

21、ms. Dimensions and tolerances for straight ducts given in this standard are in accordance with ISO 7807: 19833 concerning recommended sizes. It is intended that the additional sizes (A) which are in use in some countries will be phased out and may be removed from a future edition of the standard. Th

22、e dimensions given for duct fittings are based on document EUROVENT 2/4 4. EN 1506:2007 (E) 6 1 Scope This European Standard specifies dimensions of ducts and duct fittings with circular cross- section. It applies to ductwork used in ventilating and air conditioning systems in buildings, subject to

23、human occupancy. The wall thickness of ducts and fittings is not specified in this standard; strength and leakage are dealt with in EN 12237 2. The corresponding standard for rectangular ducts is EN 1505 1. 2 Normative references The following referenced documents are indispensable for the applicati

24、on of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12792:2003, Ventilation for buildings - Symbols, terminology and graphical symbols 3 Terms, definitions and symbols

25、For the purposes of this document, the terms and definitions given in EN 12792:2003 and the following apply. 3.1 nominal size (d, d1, d2, d3and d4) reference dimension used for designation, calculation and application of ducts and fittings d denotes the inner diameter of ducts and female ends. d1, d

26、2, d3and d4denote the outer diameters of male ends of fittings. 3.2 effective length of a fitting (l, l1, and l3) length by which a fitting contributes to the overall length of the air distribution system 3.3 effective length of a straight duct (L) length by which a straight duct contributes to the

27、overall length of the air distribution system 3.4 overlap (insertion) length (lp) length by which a fitting overlaps the duct EN 1506:2007 (E) 7 3.5 cross-sectional area (Ac) for ducts with circular cross-section the cross-sectional area Acis equal to Ac= d423.6 straight duct surface area (Ai) produ

28、ct of the internal perimeter and the duct length For ducts with circular cross-section the duct surface area per metre length is Ai= d 3.7 Deviation, tolerance, clearance (see Figure 10) 3.7.1 upper deviation algebraic difference between the maximum limit of size and the corresponding nominal size 3

29、.7.2 lower deviation algebraic difference between the minimum limit of size and the corresponding nominal size 3.7.3 tolerance difference between the upper deviation and the lower deviation. The tolerance is an absolute value without sign 3.7.4 clearance positive difference between the sizes of a fe

30、male connector or duct and of a male connector 4 Dimensions and values for ducts The nominal diameter d, cross-sectional area Acand duct surface area Aiare given in Table 1. The nominal diameters also apply to fittings. Tolerances, deviations and clearances are given in Clause 6. EN 1506:2007 (E) 8

31、Table 1 Ducts with circular cross-section: dimensions Nominal diameter, d mm Cross-sectional area, Ac m2Duct surface area, Ai m2/m Recommended sizes 63 3,12 10-30,197 80 5,03 10-30,251 100 7,85 10-30,314 125 12,3 10-30,393 160 20,1 10-30,502 200 31,4 10-30,628 250 49,1 10-30,785 315 77,9 10-30,990 4

32、00 0,126 1,26 500 0,19 1,57 630 0,312 1,98 800 0,503 2,51 1000 0,785 3,14 1250 1,23 3,93 Additional sizes 150 17,7 10-30,471 300 70,7 10-30,943 355 98,9 10-31,11 450 0,159 1,41 560 0,246 1,76 710 0,39 2,23 900 0,636 2,83 1120 0,985 3,52 NOTE Recommended sizes correspond to the sizes stated in ISO 78

33、07. 5 Dimensions for fittings 5.1 General The nominal diameters are given in Table 1. NOTE Pressed fittings are available in various forms and are normally limited to diameters not exceeding 315 mm. 5.2 Joints The overlap length of overlapping joints is given in Table 2. EN 1506:2007 (E) 9 Table 2 O

34、verlap length Nominal diameter in mm 63 to 315 315 to 800 800 to 1250 lpin mm 25 50 100 For butt joints (see Figure A.3d) the diameters of the ducts to be connected at the joints are equal. 5.3 Bends 5.3.1 General The radius of bends rmfor different nominal sizes is given in Table 3. Table 3 Radius

35、of bends diin mm rmin mm 100 100 100 d1The effective length is given by the formula:l = rm. tan (/2) Bends with 15 and 30 angle are also available. 5.3.2 Pressed bends Examples of pressed bends are shown in Figure 2. Key a) 90 bend, l = rmb) 45 bend, l = 0,41 rm c) 30 bend, l = 0,27 rmFigure 2 Dimen

36、sions for pressed bends EN 1506:2007 (E) 10 5.3.3 Segmented bends Examples of segmented bends are shown in Figure 3. Key a) 90 bend, l = rmb) 45 bend, l = 0,41 rm c) 30 bend, l = 0,27 rmminimum 3 segments minimum 2 segments minimum 2 segments Figure 3 Dimensions for segmented bends 5.4 Branches and

37、T-pieces 5.4.1 General Dimensions for branches and T-pieces are given in Table 4. Recommended sizes are indicated by an “R” and additional sizes by an “A”. Examples of branches and T-pieces are shown in Figures 4, 5 and 6. EN 1506:2007 (E) 11 5.4.2 Branches Key a) Pressed formed branch b) Conical br

38、anch r 10 m s 0,15 d3l3 0,5 d + r l3 0,5 d + s Figure 4 Examples of branches 5.4.3 T-pieces Key l1 0,5 d3+ r l3 0,5 d1+ r r 10 mm Figure 5 Example of T-piece with concentric pressed formed branch EN 1506:2007 (E) 12 Key a) Concentric branch b) Tangential branch l1 0,5 d3+ s l3 0,5 d1+ s s 0,15 d3Fig

39、ure 6 Examples of T-pieces with conical branch Table 4 Dimensions for branches and T-pieces d363 80 100 125 150 160 200 250 300 315 355 400 450 500 560 630 710 800 900 1000 1120 1250 d,d1mm 80 R R - - - - - - - - - - - - - - - - - - - 100 R R R - - - - - - - - - - - - - - - - - - 125 - R R R - - - -

40、 - - - - - - - - - - - - - 150 - A A A A - - - - - - - - - - - - - - - - - 160 - R R R A R - - - - - - - - - - - - - - - - 200 - R R R A R R - - - - - - - - - - - - - - - 250 - R R R A R R R - - - - - - - - - - - - - - 300 - - A A A A A A A - - - - - - - - - - - - - 315 - - R R A R R R A R - - - - -

41、 - - - - - - - 355 - - - - - A A A A A A - - - - - - - - - - - 400 - - - - - R R R A R A R - - - - - - - - - - 450 - - - - - - A A A A A A A - - - - - - - - - 500 - - - - - - R R A R A R A R - - - - - - - - 560 - - - - - - - A A A A A A A A - - - - - - - 630 - - - - - - - R A R A R A R A R - - - - -

42、 - 710 - - - - - - - - - A A A A A A A A - - - - - 800 - - - - - - - - - R A R A R A R A R - - - - 900 - - - - - - - - - - - A A A A A A A A - - - 1000 - - - - - - - - - - - R A R A R A R A R - - 1120 - - - - - - - - - - - - - A A A A A A A A - 1250 - - - - - - - - - - - - - R A R A R A R A R R - Re

43、commended sizes A - Additional sizes. EN 1506:2007 (E) 13 5.4.4 Special pieces Examples of special pieces are shown in Figure 7. Key a) T-piece with 45 branch b) Cross (X-piece) Figure 7 Special pieces 5.4.5 Transformation pieces Dimensions for transformation pieces are given in Table 5. Recommended

44、 sizes are indicated by an “R” and additional sizes by an “A”. Examples of transformation pieces with two male ends are shown in Figure 8. Transformation pieces with female ends and combinations of male and female ends are also available. Key a) Concentric b) Eccentric l = (d1- d2)/2 tan (/2) l = (d

45、1- d2)/tan For diameters up to and including 315 mm, transformation pieces are normally pressed. In these cases may be increased to a maximum of 90. Figure 8 Examples of tapered concentric and eccentric transformation pieces EN 1506:2007 (E) 14 Table 5 Dimensions for transformation pieces d3m d1mm 6

46、3 80 100 125 150 160 200 250 300 315 355 400 450 500 560 630 710 800 900 1000 1120 1250 80 R - - - - - - - - - - - - - - - - - - - - - 100 R R - - - - - - - - - - - - - - - - - - - - 125 R R R - - - - - - - - - - - - - - - - - - - 150 - A A A - - - - - - - - - - - - - - - - - - 160 - R R R A - - - -

47、 - - - - - - - - - - - - - 200 - - R R A R - - - - - - - - - - - - - - - - 250 - - - R A R R - - - - - - - - - - - - - - - 300 - - - - A A A A - - - - - - - - - - - - - - 315 - - - - - R R R - - - - - - - - - - - - - - 355 - - - - - - A A A A - - - - - - - - - - - - 400 - - - - - - - R A R A - - - -

48、 - - - - - - - 450 - - - - - - - - A A A A - - - - - - - - - - 500 - - - - - - - - - - A R A - - - - - - - - - 560 - - - - - - - - - - - A A A - - - - - - - - 630 - - - - - - - - - - - - A R A - - - - - - - 710 - - - - - - - - - - - - - A A A - - - - - - 800 - - - - - - - - - - - - - - A R A - - - -

49、 - 900 - - - - - - - - - - - - - - - A A A - - - - 1000 - - - - - - - - - - - - - - - - R R A - - - 1120 - - - - - - - - - - - - - - - - - A A A - - 1250 - - - - - - - - - - - - - - - - - - A R - - R - Recommended sizes. A - Additional sizes. 5.4.6 Closures The nominal diameter of the closures is given in Table 1. Examples of closures are shown in Figure 9. Key a) Plug end (for ducts and female ends) b) Cap