DIN EN 15048-1-2016 Non-preloaded structural bolting assemblies - Part 1 General requirements German version EN 15048-1 2016《非预加载荷结构的螺栓连接组件 第1部分 一般要求 德文版本EN 15048-1-2016》.pdf

《DIN EN 15048-1-2016 Non-preloaded structural bolting assemblies - Part 1 General requirements German version EN 15048-1 2016《非预加载荷结构的螺栓连接组件 第1部分 一般要求 德文版本EN 15048-1-2016》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 15048-1-2016 Non-preloaded structural bolting assemblies - Part 1 General requirements German version EN 15048-1 2016《非预加载荷结构的螺栓连接组件 第1部分 一般要求 德文版本EN 15048-1-2016》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、September 2016 English price group 15No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 21.060.01!%3q“2561678www.din.d

2、eDIN EN 15048-1Nonpreloaded structural bolting assemblies Part 1: General requirements;English version EN 150481:2016,English translation of DIN EN 15048-1:2016-09Garnituren fr nicht vorgespannte Schraubverbindungen im Metallbau Teil 1: Allgemeine Anforderungen;Englische Fassung EN 150481:2016,Engli

3、sche bersetzung von DIN EN 15048-1:2016-09Boulonnerie de construction mtallique non prcontrainte Partie 1: Exigences gnrales;Version anglaise EN 150481:2016,Traduction anglaise de DIN EN 15048-1:2016-09SupersedesDIN EN 150481:200707See start of applicationwww.beuth.deDocument comprises 34 pagesDTran

4、slation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.09.16 DIN EN 15048-1:2016-09 2 A comma is used as the decimal marker. Start of application The start of application of this standard is 2016-09-01. It should be noted that, in Germany, CE c

5、onformity marking of construction products will be permitted once this standard has been listed in the Official Journal of the European Union and/or the Bundesanzeiger (German Federal Gazette) and from the date given therein. For further information, users of this standard should refer to the websit

6、es of the European Commission or of the relevant building authority. The standard which this document replaces, DIN EN 15048-1:2007-07, may be used in parallel with this standard during a specified transition period where such has been laid down in the Official Journal of the European Union and/or t

7、he Bundesanzeiger (German Federal Gazette). National foreword This document (EN 15048-1:2016) has been prepared by Technical Committee CEN/TC 185 “Fasteners” (Secretariat: BSI, United Kingdom). The responsible German body involved in its preparation was DIN-Normenausschuss Mechanische Verbindungsele

8、mente (DIN Standards Committee Fasteners), Working Committee NA 067-00-07 AA Verbindungselemente fr den Metallbau. The European Standards referred to in this document have been published as DIN EN or DIN EN ISO Standards with the same number. The DIN Standards corresponding to the International Stan

9、dards referred to in this document are as follows: ISO 965-1 DIN ISO 965-1 ISO 965-2 DIN ISO 965-2 ISO 965-3 DIN ISO 965-3 ISO 965-4 DIN ISO 965-4 ISO 965-5 DIN ISO 965-5 Amendments This standard differs from DIN EN 15048-1:2007-07 as follows: a) the word “planmig” has been deleted from the title of

10、 the German version; b) based upon the Regulation (EC) No. 305/2011, the standard has been completely revised; c) the requirements of this standard are only related to the product characteristics of bolting assemblies which are necessary for CE marking; the assembly now comprises bolt and nut, but n

11、o washer. Previous editions DIN EN 15048-1: 2007-07 DIN EN 15048-1:2016-09 3 National Annex NA (informative) Bibliography DIN ISO 965-1, ISO general purpose metric screw threads Tolerances Part 1: Principles and basic data DIN ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Li

12、mits of sizes for general purpose external and internal screw threads Medium quality DIN ISO 965-3, ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional threads DIN ISO 965-4, ISO general purpose metric screw threads Tolerances Part 4: Limits of sizes for hot-dip

13、 galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing DIN ISO 965-5, ISO general purpose metric screw threads Tolerances Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads

14、with maximum size of tolerance position h before galvanizing DIN EN 15048-1:2016-09 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15048-1 July 2016 ICS 21.060.01 Supersedes EN 15048-1:2007English Version Non-preloaded structural bolting assemblies - Part 1:

15、General requirements Boulonnerie de construction mtallique non prcontrainte - Partie 1: Exigences gnrales Garnituren fr nicht vorgespannte Schraubverbindungen im Metallbau - Teil 1: Allgemeine Anforderungen This European Standard was approved by CEN on 19 March 2015. CEN members are bound to comply

16、with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Ma

17、nagement Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same

18、status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, M

19、alta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 C

20、EN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15048-1:2016 EEN 15048-1:2016 (E) 2 Contents Page European foreword . 3 Introduction 5 1 Scope 6 2 Normative references 6 3 Terms and definitions . 7 4 Product characteristics . 8 4.1

21、General 8 4.2 Type (bolting assemblies) 8 4.3 Property class (bolting assemblies) 11 4.4 Product grade (bolts and nuts) . 13 5 Testing and assessment methods . 14 5.1 General . 14 5.2 Type (bolting assemblies) - Axial load (bolting assemblies) . 14 5.3 Property class (bolting assemblies) 14 5.4 Prod

22、uct grade (bolts and nuts) . 15 6 Assessment and Verification of Constancy of Performance (AVCP) 16 6.1 General . 16 6.2 Type-testing . 17 6.3 Factory production control (FPC) 18 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Regula

23、tion 24 ZA.1 Scope and relevant characteristics 24 ZA.2 Procedure for Assessment and Verification of Constancy of Performance (AVCP) of Non-preloaded structural bolting assemblies . 24 ZA.3 CE marking and labelling 28 Bibliography . 30 DIN EN 15048-1:2016-09EN 15048-1:2016 (E) 3 European foreword Th

24、is document (EN 15048-1:2016) has been prepared by Technical Committee CEN/TC 185 “Fasteners“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2017

25、, and conflicting national standards shall be withdrawn at the latest by April 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. T

26、his document supersedes EN 15048-1:2007. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports basic work requirements of Regulation (EU) No 305/2011. For relationship with Regulation (EU) No 305/2011 see informa

27、tive Annex ZA, which is an integral part of this document. EN 15048 consists of the following parts, under the general title Non-preloaded structural bolting assemblies: Part 1: General requirements; Part 2: Fitness for purpose. Compared to the previous version, the modifications are the following:

28、the standard was revised to meet the new format for harmonized standards and in relation to the Regulation (EU) No. 305/2011 (CPR); the requirements of this standard only relate to the product characteristics of bolting assemblies which are necessary for CE marking; all clauses dealing with further

29、technical or other requirements have been transferred to EN 15048-2; washers are not considered as part of the non-preloaded bolting assemblies, however they can be used as relevant; addition of bolting assemblies made in aluminum and aluminum alloys; addition of nominal diameters M5 to M10; Railway

30、 rail fasteners have been excluded. DIN EN 15048-1:2016-09EN 15048-1:2016 (E) 4 According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republi

31、c, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN

32、15048-1:2016-09EN 15048-1:2016 (E) 5 Introduction Rules for design and execution of bolted connections with non-preloaded structural bolts are defined for instance in EN 1993-1-8 and EN 1090-2 for steel structures or EN 1999-1-1 and EN 1090-3 for aluminium or aluminium alloy structures. The parts of

33、 this European Standard on structural bolting assemblies specify the general requirements which ensure that bolting assemblies comprising bolts and nuts are suitable for use as non-preloaded structural bolting in structural metallic works. They can be used in shear connections and/or in tension conn

34、ections if no preload is required. Structural bolting assemblies which meet the requirements of this part of this European Standard have been designed to allow tensile resistance of at least fub As. For this purpose the tensile test of bolting assemblies specified in EN 15048-2 is a mean to check wh

35、ether the function of the assembly is fulfilled. Washers or other elements can be used additionally if necessary. DIN EN 15048-1:2016-09EN 15048-1:2016 (E) 6 1 Scope This part of this European Standard specifies the general requirements for bolting assemblies for non-preloaded structural bolting. Bo

36、lting assemblies in accordance with this European Standard are designed to be used in structural bolting connections for shear and/or tensile loading. The intended use of bolting assemblies in accordance with this European standard is structural metallic works. It applies to bolts (the term used whe

37、n bolts partially threaded, screws, studs and stud-bolts are considered all together) and nuts made of carbon steel, alloy steel, stainless steel or aluminium or aluminium alloy with the following property classes: bolts made of carbon steel or alloy steel: 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, 10.9 (in acc

38、ordance with EN ISO 898-1); nuts made of carbon steel or alloy steel: 5, 6, 8, 10, 12 (in accordance with EN ISO 898-2); bolts made of austenitic stainless steel: 50, 70, 80 (in accordance with EN ISO 3506-1); nuts made of austenitic stainless steel: 50, 70, 80 (in accordance with EN ISO 3506-2); bo

39、lts made of aluminium or aluminium alloy: AL1 to AL6 (in accordance with EN 28839); nuts made of aluminium or aluminium alloy: AL1 to AL6 (in accordance with EN 28839). This European Standard applies to bolting assemblies with ISO metric coarse pitch thread from sizes M12 to M39 for use in steel str

40、uctures according to EN 1090-2, and from M5 to M39 for use in aluminium or aluminium alloy structures according to EN 1090-3. The use of thread sizes larger than M39 is not precluded provided all applicable requirements of this standard are met. WARNING Only bolting assemblies are covered by this ha

41、rmonized standard: separate bolts or nuts, not tested as part of an assembly lot of bolting assemblies in accordance with EN 15048-2, are not covered by this harmonized standard and cannot be CE marked. NOTE 1 The property classes 4.8, 5.8 and 6.8 may be subjected to limitations of use. NOTE 2 High-

42、strength structural bolting assemblies for preloading which meet the requirements of EN 143991 are not within the scope of this European Standard but they are also suitable for use in non-preloaded structural bolting. NOTE 3 Bolts and nuts made of aluminium or aluminium alloys are not designed to be

43、 used in steel structures, see EN 10902. Bolting assemblies in accordance with this European Standard are not designed to be welded. Railway rail fasteners are not covered by this European Standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in th

44、is document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1090-2, Execution of steel structures and aluminium structures Part 2: Technical r

45、equirements for steel structures DIN EN 15048-1:2016-09EN 15048-1:2016 (E) 7 EN 15048-2, Non-preloaded structural bolting assemblies Part 2: Suitability test EN 28839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals (ISO 8839) EN ISO 225, Fasteners Bolts,

46、screws, studs and nuts Symbols and descriptions of dimensions (ISO 225) EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread (ISO 898-1) EN ISO 898-2, Mechanical prope

47、rties of fasteners made of carbon steel and alloy steel Part 2: Nuts with specified property classes Coarse thread and fine pitch thread (ISO 898-2) EN ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs (ISO 3506-1) EN ISO 3506-2, Mecha

48、nical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts (ISO 3506-2) EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C (ISO 4759-1) EN ISO 10684:2004, Fasteners Hot dip galvanized coatings (ISO 10684:2004) ISO 965-1, ISO ge

49、neral purpose metric screw threads Tolerances Part 1: Principles and basic data ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality ISO 965-3, ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional screw threads ISO 965-4, ISO general