DIN EN 14910-2009 Garden equipment - Walk-behind combustion engine powered trimmers - Safety (includes Amendment A1 2009) English version of DIN EN 14910 2009-08《园艺设备 步行式内燃机驱动的修剪机 .pdf

《DIN EN 14910-2009 Garden equipment - Walk-behind combustion engine powered trimmers - Safety (includes Amendment A1 2009) English version of DIN EN 14910 2009-08《园艺设备 步行式内燃机驱动的修剪机 .pdf》由会员分享，可在线阅读，更多相关《DIN EN 14910-2009 Garden equipment - Walk-behind combustion engine powered trimmers - Safety (includes Amendment A1 2009) English version of DIN EN 14910 2009-08《园艺设备 步行式内燃机驱动的修剪机 .pdf（50页珍藏版）》请在麦多课文档分享上搜索。

1、August 2009DEUTSCHE NORM English price group 18No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 65.060.70!$Y(r“1540579w

2、ww.din.deDDIN EN 14910Garden equipment Walk-behind combustion engine powered trimmers Safety (includes Amendment A1:2009)English version of DIN EN 14910:2009-08Gartengerte Handgefhrte Trimmer mit Verbrennungsmotor Sicherheit (enthlt nderung A1:2009)Englische Fassung DIN EN 14910:2009-08SupersedesDIN

3、 EN 14910:2007-08See start of validitywww.beuth.deDocument comprises pages50DIN EN 14910:2009-08 Start of validity This standard takes effect on 1 August 2009. DIN EN 14910:2007-08 may be used in parallel until 28 December 2009. National foreword This standard includes safety requirements within the

4、 meaning of the Gerte- und Produktsicherheitsgesetz (GPSG) (German Equipment and Product Safety Act). This standard has been prepared by Technical Committee CEN/TC 144 “Tractors and machinery for agriculture and forestry” (Secretariat: AFNOR, France), Working Group WG 7 “Garden equipment” (Secretari

5、at: BSI, United Kingdom). The responsible German body involved in its preparation was the Normenausschuss Eisen, Blech- und Metall-waren (Hardware, Tinware and Metal Products Standards Committee), Technical Committee NA 020-00-11 AA Garten- und Rasenpflegegerte. This standard contains specifications

6、 meeting the essential requirements set out in Annex I of the “Machinery Directive”, Directive 98/37/EC, (valid until 28 December 2009) and the “revised Machinery Directive”, Directive 2006/42/EC, which takes effect on 29 December 2009, and which apply to machines that are either first placed on the

7、 market or commissioned within the EEA. This standard serves to facilitate proof of compliance with the essential requirements of the directives. Once this standard is cited in the Official Journal of the European Union, it is deemed a “harmonized” standard and thus, a manufacturer applying this sta

8、ndard may assume compliance with the requirements of the Machinery Directive (“presumption of conformity”). Amendments This standard differs from DIN EN 14910:2007-08 as follows: a) In subclause 6.1, a NOTE has been included relating to information on noise emission in the sales literature. b) In su

9、bclause 6.2.1, the marking requirements have been brought in line with the Machinery Directive. c) Annex ZA (informative) “Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC” has been revised. d) Annex ZB (informative) “Relationship between this Europ

10、ean Standard and the Essential Requirements of EU Directive 2006/42/EC” has been included. Previous editions DIN EN 14910: 2007-08 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14910:2007+A1 April 2009 ICS 65.060.70 Supersedes EN 14910:2007English Version Garden equipment - Walk-behind comb

11、ustion engine powered trimmers - Safety Matriel de jardinage - Coupe-gazon moteur combustion interne et conducteur pied - Scurit Gartengerte - Handgefhrte Trimmer mit Verbrennungsmotor - Sicherheit This European Standard was approved by CEN on 22 March 2007 and includes Amendment 1 approved by CEN o

12、n 14 March 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may

13、 be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CE

14、N Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlan

15、ds, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in a

16、ny form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14910:2007+A1:2009: EEN 14910:2007+A1:2009 (E) 2 Contents Page Foreword . 4Introduction 51 Scope 62 Normative references . 63 Terms and definitions . 74 List of significant hazards 85 Safety requirements and/or measure

17、s and means of verification . 105.1 General . 105.2 Guards 105.2.1 General . 105.2.2 Power driven components (other than the cutting means) 105.2.3 Guarding of cutting means 105.2.4 Hot surfaces 125.3 Protection from exhaust fumes . 135.4 Liquid spillage . 135.5 Tank openings . 135.6 Controls . 135.

18、7 Electrical requirements for battery circuits and high tension ignition circuits 135.7.1 Electrical cables 135.7.2 Battery installation 135.7.3 Overload protection 145.7.4 Terminals and un-insulated electrical parts . 145.7.5 High voltage parts . 145.8 Engine stopping and starting 145.9 Handle cons

19、truction . 145.10 Vibration . 155.10.1 Reduction by design and protective measures . 155.10.2 Reduction by information. 155.10.3 Vibration measurement 155.11 Noise. 155.11.1 Reduction as a safety requirement . 155.11.2 Noise emission measurement . 165.12 Cutting means . 165.12.1 General . 165.12.2 C

20、utting elements . 165.13 Mechanical strength and rigidity . 175.13.1 General . 175.13.2 Cutting means guard (mechanical strength and rigidity) . 175.13.3 Mechanical strength of cutting head 186 Information for use . 186.1 Instructions for use . 186.2 Marking 196.2.1 Minimum marking . 196.2.2 Warning

21、s 206.2.3 Cutting head 206.2.4 Marking durability . 206.2.5 Test . 21Annex A (normative) Vibration (see 5.10) 28DIN EN 14910:2009-08 EN 14910:2007+A1:2009 (E) 3 A.1 Quantities to be measured . 28A.2 Instrumentation . 28A.2.1 General . 28A.2.2 Fastening of transducer . 28A.2.3 Calibration . 28A.3 Mea

22、surement direction and measurement location 28A.3.1 Measurement direction . 28A.3.2 Measurement location 28A.4 Test procedure 29A.4.1 Determination of working procedure 29A.4.2 Test method . 29A.5 Measurement procedure 29A.6 Determination of the measurement result 29Annex B (normative) Noise test co

23、de Engineering method (grade 2) (see 5.11) 32B.1 General . 32B.2 Scope 32B.3 Sound power level determination . 32B.4 A-weighted emission sound pressure level determination 34B.5 Requirements for test floor 34B.5.1 Artificial surface 34B.5.2 Natural grass . 35B.6 Installation, mounting and operating

24、conditions 35B.7 Information to be recorded and reported . 36B.8 Measurement uncertainties and declaration of noise emission values 36Annex C (informative) Example of a material and construction fulfilling the requirements for an artificial surface as required by B.5.1 37C.1 Material . 37C.2 Constru

25、ction 37Annex D (normative) Calculation of kinetic energy (see 5.12.1) . 39Annex E (normative) Safety signs for use on trimmers (see 6.2.2) . 40Annex F (informative) Safety instructions . 43F.1 Introduction . 43F.2 General provisions 43F.3 Safe operating practices 43F.3.1 Training 43F.3.2 Preparatio

26、n 43F.3.3 Operation . 44F.3.4 Maintenance and storage . 45Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC“ . 46Annex ZB (informative) !Relationship between this European Standard and the Essential Requirements of EU Directiv

27、e 2006/42/EC“ . 47Bibliography . 48DIN EN 14910:2009-08 EN 14910:2007+A1:2009 (E) 4 Foreword This document (EN 14910:2007+A1:2009) has been prepared by Technical Committee CEN/TC 144 “Tractors and machinery for agriculture and forestry”, the secretariat of which is held by AFNOR. This European Stand

28、ard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This document includes Amendment 1, approved by CEN on 2009-03-14.

29、This document supersedes EN 14910:2007. The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential require

30、ments of EU Directive(s). !For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document.“ According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Sta

31、ndard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. DI

32、N EN 14910:2009-08 EN 14910:2007+A1:2009 (E) 5 Introduction This European Standard is a type C standard as stated in EN ISO 12100-1. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this European Standard. When provisi

33、ons of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard. DIN E

34、N 14910:2009-08 EN 14910:2007+A1:2009 (E) 6 1 Scope This European Standard deals with all significant hazards, hazardous situations and events relevant to walk-behind trimmers, powered by a combustion engine, with cutting means using non-metallic filament line or freely pivoting non-metallic cutter(

35、s), of which the cutting elements rely on centrifugal force to achieve cutting with the kinetic energy of a single cutting element not exceeding 10 J, designed for cutting grass or similar plant material, when they are used as intended and under conditions of misuse which are reasonably foreseeable

36、by the manufacturer (see Clause 4). This European Standard is not applicable to: a) walk-behind trimmers with cutting means other than those described above; b) self propelled walk-behind trimmers or walk-behind edge trimmers; c) lawnmowers using non-metallic filament line or freely pivoting non-met

37、allic cutting elements with greater than 10 J kinetic energy; NOTE 1 EN 836 applies for machines using non-metallic filament line or freely pivoting non-metallic cutting elements with greater than 10 J kinetic energy. d) motor mowers using metal or other solid cutting elements. NOTE 2 EN 12733 appli

38、es for machines using metal or other solid cutting elements. EMC and environmental hazards other than noise have not been considered in this European Standard. This European Standard is not applicable to walk-behind trimmers which are manufactured before the date of its publication as EN. NOTE 3 Law

39、n trimmers and lawn edge trimmers (electric powered) are dealt with in EN 786, grass trimmers (internal combustion engine powered) are dealt with in EN 11806 and lawn mowers (internal combustion engine powered) are dealt with in EN 836. 2 Normative references The following referenced documents are i

40、ndispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 294:1992, Safety of machinery Safety distance to prevent danger zones being r

41、eached by the upper limbs EN 1033:1995, Hand-arm vibration Laboratory measurement of vibration at the grip surface of hand-guided machinery General EN ISO 354:2003, Acoustics Measurement of sound absorption in a reverberation room (ISO 354:2003) EN ISO 3744:1995, Acoustics Determination of sound pow

42、er levels of noise sources using sound pressure Engineering method in an essentially free field over a reflecting plane (ISO 3744:1994) EN ISO 11201:1995, Acoustics Noise emitted by machinery and equipment Measurement of emission sound pressure levels at a work station and at other specified positio

43、ns Engineering method in an essentially free field over a reflecting plane (ISO 11201:1995) DIN EN 14910:2009-08 EN 14910:2007+A1:2009 (E) 7 EN ISO 11688-1:1998, Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning (ISO/TR 11688-1:1995) EN ISO 12100-1:2

44、003, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12100-2:2003) 3 Terms and definitions For the purp

45、ose of this document, the terms and definitions given in EN ISO 12100-1:2003 and the following apply. 3.1 walk-behind ground supported, possibly by wheels or air cushion and controlled by the operator walking behind (see Figure 1) 3.2 trimmer grass trimming machine where the cutting means operates i

46、n a plane approximately parallel to the ground (see Figure 1 for example of a walk-behind trimmer) NOTE Throughout the remainder of this European Standard, the term “trimmer” is used to refer to walk-behind trimmers. 3.3 cutting means mechanism used to provide the cutting action in which one or more

47、 cutting elements, cutting by impact, are supported by a cutting head and rotate about an axis normal to the cutting plane (see Figure 2 (a) 3.4 cutting element single non-metallic filament line or freely pivoting non-metallic cutter (see Figure 5) 3.5 cutting head support system for the cutting ele

48、ment (see Figures 2 (a) and 2 (b) 3.6 cutting means control device activated by the operators hand or finger, for controlling the cutting means movement 3.7 edge trimmer grass trimming machine where the cutting means operates in a plane approximately perpendicular to the ground 3.8 maximum operating

49、 engine speed highest engine speed obtainable when adjusted in accordance with the manufacturers specification and/or instructions with the cutting means engaged DIN EN 14910:2009-08 EN 14910:2007+A1:2009 (E) 8 3.9 operator presence control control designed so that it will automatically interrupt power to a drive when the operators actuating force is r