DIN EN 14898-2007 Water conditioning equipment inside buildings - Active media filters - nRequirements for performance safety and testing(includes Amendment A1 2007) nEnglish versi.pdf

《DIN EN 14898-2007 Water conditioning equipment inside buildings - Active media filters - nRequirements for performance safety and testing(includes Amendment A1 2007) nEnglish versi.pdf》由会员分享，可在线阅读，更多相关《DIN EN 14898-2007 Water conditioning equipment inside buildings - Active media filters - nRequirements for performance safety and testing(includes Amendment A1 2007) nEnglish versi.pdf（33页珍藏版）》请在麦多课文档分享上搜索。

1、September 2007DEUTSCHE NORM English price group 14No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 13.060.20; 91.140.60

2、!$HA“1378830www.din.deDDIN EN 14898Water conditioning equipment inside buildings Active media filters Requirements for performance, safety and testing (includes AmendmentA1:2007)English version of DIN EN 14898:2007-09Anlagen zur Behandlung von Trinkwasser innerhalb von Gebuden Filter mit aktiven Sub

3、stanzen Anforderungen an Ausfhrung, Sicherheit und Prfung (enthlt nderung A1:2007)Englische Fassung DIN EN 14898:2007-09SupersedesDIN EN 14898:2006-08www.beuth.deDocument comprises 33 pages 11.07DIN EN 14898:2007-09 2 National foreword This standard has been prepared by Technical Committee CEN/TC 16

4、4 “Water supply” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Wasserwesen (Water Practice Standards Committee), Technical Committee NA 119-04-07-01 UA Wasserbehandlung. Amendments This standard differs from DIN EN 14898:2006-08 as foll

5、ows: a) A new Annex D has been included. b) Terms and chemical formulae have been made more precise. Previous editions DIN EN 14898: 2006-08 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14898:2006+A1 June 2007 ICS 13.060.20; 91.140.60 Supersedes EN 14898:2006English Version Water conditionin

6、g equipment inside buildings - Active media filters - Requirements for performance, safety and testing Appareils de traitement deau lintrieur des btiments - Filtres substance active - Exigences de performance, de scurit et essais Anlagen zur Behandlung von Trinkwasser innerhalb von Gebuden - Filter

7、mit aktiven Substanzen - Anforderungen an Ausfhrung, Sicherheit und Prfung This European Standard was approved by CEN on 27 April 2006 and includes Amendment 1 approved by CEN on 10 May 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for

8、 giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three officia

9、l versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, B

10、elgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE F

11、OR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14898:2006+A1:2007: EEN 14898:2006+A1:2007

12、 (E) 2 Contents Page Foreword. 4 1 Scope . 5 2 Normative references . 5 3 Terms and definitions. 6 4 System design requirements. 8 4.1 Materials of construction . 8 4.2 Working conditions. 8 4.2.1 Working temperature 8 4.2.2 Working flow 8 4.3 Filter cartridge replacement. 8 4.4 End connections . 8

13、4.5 Backflow prevention. 8 4.6 Exchange indicator. 8 5 Performance requirements 9 5.1 Pressure strength of the filter housing 9 5.2 Dynamic pressure test of housing 9 5.3 Dynamic pressure test of cartridge. 9 5.4 Pressure drop 9 5.5 Substance reduction performance 9 5.5.1 Performance claims 9 5.5.2

14、Chlorine reduction 9 5.5.3 Organic chemical reduction. 9 5.5.4 Odour and flavour reduction . 10 5.5.5 Inorganic chemical reduction 10 6 Test methods. 10 6.1 Static pressure test of filter housing 10 6.1.1 Principle . 10 6.1.2 Procedure 10 6.2 Dynamic water pressure test of housing . 11 6.2.1 Princip

15、le . 11 6.2.2 Procedure 11 6.3 Dynamic pressure test of cartridge. 12 6.3.1 Principle . 12 6.3.2 Procedure 12 6.4 Pressure drop 13 6.4.1 Principle . 13 6.4.2 Procedure 13 6.5 Chlorine reduction 15 6.5.1 Test equipment 15 6.5.2 Reagents 15 6.5.3 Analytical methods . 15 6.5.4 Test conditions 15 6.5.5

16、Procedure 16 6.5.6 Sampling 16 6.5.7 Acceptance criteria. 17 6.5.8 Expression of results . 17 6.6 Chemical and odour/flavour reduction. 17 6.6.1 Test equipment 17 6.6.2 Reagents 17 EN 14898:2006+A1:2007 (E) 3 6.6.3 Analytical methods18 6.6.4 Test conditions 18 6.6.5 Procedure.21 6.6.6 Sampling 21 6.

17、6.7 Acceptance criteria .21 6.6.8 Expression of results21 7 Technical documents, marking, labelling and packaging.22 7.1 Technical documents22 7.2 Marking.23 7.3 Labelling.23 7.3.1 Filter housing.23 7.3.2 Filter cartridge .23 7.4 Packaging.23 Annex A (informative) Example of test rig for substance r

18、eduction testing 24 Annex B (informative) Example test report 25 Annex C (informative) Substance-specific reduction claims .26 Bibliography31 EN 14898:2006+A1:2007 (E) 4 Foreword This document (EN 14898:2006+A1:2007) has been prepared by Technical Committee CEN/TC 164 “Water supply”, the secretariat

19、 of which is held by AFNOR. This document shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2007 and conflicting national standards shall be withdrawn at the latest by December 2007. This document includes Amendm

20、ent 1, approved by CEN on 2007-05-10. This document supersedes EN 14898:2006. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. With respect to potential adverse effects on the quality of water intended for human consumption caused by the product c

21、overed by this standard, the following is pointed out to the user: 1) This standard provides no information as to whether the product may be used without restriction in any of the Member States. 2) It should be noted that, while awaiting the adoption of verifiable European criteria, existing nationa

22、l regulation concerning the use and/or the characteristics of this product remain in force. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Repu

23、blic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 14898:2006+A1:2007 (E) 5 1 Scope This European Stand

24、ard specifies requirements relating to the construction, performance and methods of testing for active media filters for drinking water installations inside buildings, with a maximum working pressure of at least 1 000 kPa and a maximum working temperature of less than 30 C. It only concerns units, w

25、hich are permanently connected to the mains supply at the point of entry or point of use. This standard applies only to filter systems comprising a housing and filter media tested together. It includes capsule type units where both the element and its outer housing are disposable. NOTE Products inte

26、nded for use in water supply systems are to comply, when existing, with national regulations and testing arrangements that ensure fitness for contact with drinking water. The Member States relevant regulators and the EC Commission agreed on the principle of a future unique European Acceptance Scheme

27、 (EAS) which would provide a common testing and approval arrangement at European level. If and when the EAS is adopted, European Standards on products will be amended by the addition of an Annex Z/EAS under Mandate M/136 which will contain formal references to the testing, certification and product

28、marking requirements of the EAS. Until the EAS comes into force, the current national regulations remain applicable. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated ref

29、erences, the latest edition of the referenced document (including any amendments) applies. EN 1717, Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow EN 12903, Products used for treatment of water intended for hu

30、man consumption Powdered activated carbon EN 12904, Products used for treatment of water intended for human consumption Silica sand and silica gravel EN 12905, Products used for treatment of water intended for human consumption Expanded aluminosilicate EN 12906, Products used for treatment of water

31、intended for human consumption Pumice EN 12907, Products used for treatment of water intended for human consumption Pyrolyzed coal material EN 12909, Products used for treatment of water intended for human consumption Anthracite EN 12910, Products used for treatment of water intended for human consu

32、mption Garnet EN 12911, Products used for treatment of water intended for human consumption Manganese Greensand EN 12912, Products used for treatment of water intended for human consumption Barite EN 12913, Products used for treatment of water intended for human consumption Powdered diatomaceous ear

33、th EN 12914, Products used for treatment of water intended for human consumption Powdered perlite EN 12915-1, Products used for treatment of water intended for human consumption Granular activated carbon Part 1: Virgin granular activated carbon EN 13752, Products used for treatment of water intended

34、 for human consumption Manganese dioxide EN 14898:2006+A1:2007 (E) 6 EN 13753, Products used for treatment of water intended for human consumption Granular activated alumina EN 13754, Products used for treatment of water intended for human consumption Bentonite EN 14368, Products used for treatment

35、of water intended for human consumption Manganese dioxide coated limestone EN 14369, Products used for treatment of water intended for human consumption Iron-coated granular activated alumina EN 27888, Water quality Determination of electrical conductivity (ISO 7888:1985) EN ISO 3696, Water for anal

36、ytical laboratory use Specification and test methods (ISO 3696:1987) EN ISO 7027, Water quality Determination of turbidity (ISO 7072:1999) EN ISO 7393-1, Water quality Determination of free chlorine and total chlorine Part 1: Titrimetric method using N,N-diethyl-1,4-phenylenediamine (ISO 7393-1:1985

37、) ISO 10523, Water quality Determination of pH 3 Terms and definitions For the purposes of this document, the following terms and definitions apply: 3.1 active media adsorbent, ion exchange or chemically active material that removes or significantly reduces a component from water by chemical reactio

38、n or by virtue of ionic charge or other surface activity 3.2 capsule cartridge sealed cartridge, designed to be used in a support housing NOTE For this design, the housing may not be watertight. 3.3 capsule filter complete filter, for which the filter element and the filter housing are inseparable a

39、nd the housing is discarded with the spent element 3.4 cartridge replaceable filter element NOTE This includes any other components that the manufacturer specifies should be changed when the cartridge exchange is due. 3.5 cartridge exchange indicator means by which the need to change a cartridge is

40、indicated NOTE It may work by elapsed time, throughput of water or any other suitable method of indication. This indicator can only be regarded as a guide. EN 14898:2006+A1:2007 (E) 7 3.6 identification mark identification on the product and/or packaging that the product conforms to the requirements

41、 of this standard, e.g. “This product conforms to prEN 14898“ 3.7 filter element part of the filter that contains the active media 3.8 filter rated capacity volumetric capacity of the filter claimed by the manufacturer NOTE If more than one substance-specific reduction claim is made by the manufactu

42、rer, the filter rated capacity is the capacity for the substance with the lowest substance-specific rated capacity. 3.9 maximum working pressure manufacturers stipulated maximum water supply pressure above which the structural integrity of the system may be compromised 3.10 maximum working temperatu

43、re manufacturers stipulated maximum water supply temperature above which filter performance and/or structural integrity of the system may be compromised 3.11 minimum reduction rate minimum percentage reduction achieved by a filter with respect to a specified substance, as defined in the performance

44、requirements of this standard 3.12 minimum working pressure manufacturers stipulated minimum water supply pressure below which filter performance may be compromised 3.13 minimum working temperature manufacturers stipulated minimum water supply temperature below which filter performance and/or struct

45、ural integrity of the system may be compromised 3.14 substance-specific rated capacity volume of water, in litres, that the filter is capable of treating to the minimum reduction rate with respect to a specific substance 3.15 unit volume internal empty vessel volume of the complete system which is i

46、n contact with the drinking water 3.16 working flow range manufacturers stipulated maximum and minimum flow rates outside of which the performance of the filter may be compromised EN 14898:2006+A1:2007 (E) 8 4 System design requirements 4.1 Materials of construction Active media shall conform to the

47、 requirements for water extractable substances in EN 12903, EN 12904, EN 12905, EN 12906, EN 12907, EN 12909, EN 12910, EN 12911, EN 12912, EN 12913, EN 12914, EN 12915-1, EN 13752, EN 13753, EN 13754, EN 14368 or EN 14369, if and as appropriate. 4.2 Working conditions 4.2.1 Working temperature The

48、filter shall be designed to operate to the requirements of this standard at: minimum ambient air and water temperatures of not less than 5 C; maximum water temperature of at least 30 C; maximum ambient air temperature of at least 30 C. 4.2.2 Working flow Performance tests shall be performed at the m

49、aximum of the working flow range stipulated by the manufacturer. If the filter system is not fitted with a flow regulator, the manufacturer shall provide guidance in the operating instructions for adjusting the flow such that it does not exceed the maximum of the working flow range. 4.3 Filter cartridge replacement Any tools necessary for routine maintenance shall not come into contact with the water intended for human consumption. Any special tools shall be provided by the equipment supplier. The