DIN EN 14595-2016 Tanks for transport of dangerous goods - Service equipment - Breather device German version EN 14595 2016《危险物品运输罐 辅助设备 通气装置 德文版本EN 14595-2016》.pdf

《DIN EN 14595-2016 Tanks for transport of dangerous goods - Service equipment - Breather device German version EN 14595 2016《危险物品运输罐 辅助设备 通气装置 德文版本EN 14595-2016》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 14595-2016 Tanks for transport of dangerous goods - Service equipment - Breather device German version EN 14595 2016《危险物品运输罐 辅助设备 通气装置 德文版本EN 14595-2016》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、October 2016 English price group 10No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 13.300; 23.020.20!%5“2579918www.

2、din.deDIN EN 14595Tanks for transport of dangerous goods Service equipment Breather device;English version EN 14595:2016,English translation of DIN EN 14595:2016-10Tanks fr die Befrderung gefhrlicher Gter Bedienungsausrstung Belftungseinrichtung;Englische Fassung EN 14595:2016,Englische bersetzung v

3、on DIN EN 14595:2016-10Citernes destines au transport de matires dangereuses quipements de service pour citernes Dispositif de respiration;Version anglaise EN 14595:2016,Traduction anglaise de DIN EN 14595:2016-10SupersedesDIN EN 14595:200506www.beuth.deDocument comprises 15 pagesDTranslation by DIN

4、-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.10.16 DIN EN 14595:2016-10 2 A comma is used as the decimal marker. National foreword This document (EN 14595:2016) has been prepared by Technical Committee CEN/TC 296 “Tanks for the transport of dangero

5、us goods” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was DIN-Normenausschuss Tankanlagen (DIN Standards Committee Tank Installations), Working Committee NA 104-02-07 AA Ausrstungen fr Transporttanks. The DIN Standard corresponding to the International Stand

6、ard referred to in this document is as follows: ISO 2859-1 DIN ISO 2859-1 Amendments This standard differs from DIN EN 14595:2005-06 as follows: a) the device name has been changed to align it with ADR; b) the Introduction has been revised to clarify the combination of breather and safety device as

7、requirements for compliance with this standard and to include reference to EN 16522; c) EN 12266-2 has been removed from the normative reference list; d) the requirement for secondary positive means of security has been clarified; e) the below atmospheric relieving pressure rating has been clarified

8、; f) electrical resistance requirements have been refined; g) the keeping period for test results has been clarified; h) the dimensions of sand boxes for the drop test rig have been improved (Annex A). Previous editions DIN EN 14595: 2005-06 National Annex NA (informative) Bibliography DIN ISO 2859-

9、1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14595 August 2016 ICS 13.300; 23.020.20 Supersedes EN 14595:2005English Version Tanks for transport of

10、 dangerous goods - Service equipment - Breather device Citernes destines au transport de matires dangereuses - quipement de service pour citernes - Dispositif de respiration Tanks fr die Befrderung gefhrlicher Gter - Bedienungsausrstung - Belftungseinrichtung This European Standard was approved by C

11、EN on 25 June 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards

12、may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notifie

13、d to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Icela

14、nd, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Managem

15、ent Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14595:2016 EEN 14595:2016 (E) 2 Contents Page European foreword 3 Introduction 5 1 Scope . 6 2 Normative references 6 3 Terms and de

16、finitions . 6 4 Functions . 6 5 Design characteristics . 6 5.1 General . 6 5.2 Ingress protection 7 5.3 Pressure ratings 7 5.3.1 Above atmospheric relieving pressure (pressure relief). 7 5.3.2 Below atmospheric relieving pressure (vacuum) 7 5.3.3 Tank overturn 7 5.4 Flow capacity 7 5.5 Temperature r

17、ange 7 5.6 Materials of construction . 7 5.7 Dimensional characteristics . 7 5.8 Electrical resistance . 7 6 Tests 7 6.1 General . 7 6.2 Production tests 8 6.2.1 General . 8 6.2.2 Seat tightness test . 8 6.2.3 Overturn seat tightness test 9 6.3 Type test . 9 6.3.1 General . 9 6.3.2 Seat tightness te

18、st . 9 6.3.3 Overturn seat tightness test 9 6.3.4 Drop test 10 6.3.5 Test results . 11 7 Marking . 11 8 Installation, operating and maintenance instructions 11 Annex A (normative) Drop test apparatus 12 DIN EN 14595:2016-10Bibliography . 13 EN 14595:2016 (E) 3 European foreword This document (EN 145

19、95:2016) has been prepared by Technical Committee CEN/TC 296 “Tanks for transport of dangerous goods”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Fe

20、bruary 2017, and conflicting national standards shall be withdrawn at the latest by February 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. Th

21、is document supersedes EN 14595:2005. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. The following significant changes were made in this new edition of EN 14595: device name changed to align with ADR, Introduction revi

22、sed to clarify the combination of breather and safety device as requirements for compliance with this standard and to include reference to EN 16522, EN 12266-2 removed from the normative reference list, requirement for secondary positive means of security clarified, below atmospheric relieving press

23、ure rating clarified, electrical resistance requirements refined, the keeping period for test results clarified, drop test rig, (Annex A), dimensions of sand boxes improved. This document forms part of a coherent standards programme (i.e. Tanks for transport of liquid dangerous goods with vapour pre

24、ssure not exceeding 110 kPa (absolute) at 50 C and petrol Service equipment). This standards programme comprises the following standards: EN 13082, Tanks for transport of dangerous goods Service equipment for tanks Vapour transfer valve; EN 13083, Tanks for transport of dangerous goods Service equip

25、ment for tanks Adaptor for bottom loading and unloading; EN 13308, Tanks for transport of dangerous goods Service equipment for tanks Non pressure balanced footvalve; EN 13314, Tanks for transport of dangerous goods Service equipment for tanks Fill hole cover; EN 13315, Tanks for transport of danger

26、ous goods Service equipment for tanks Gravity discharge coupler; DIN EN 14595:2016-10EN 14595:2016 (E) 4 EN 13316, Tanks for transport of dangerous goods Service equipment for tanks Pressure balanced footvalve; EN 13317, Tanks for transport of dangerous goods Service equipment for tanks Manhole cove

27、r assembly; EN 14595, Tanks for transport of dangerous goods Service equipment Breather device; EN 14596, Tanks for transport of dangerous goods Service equipment for tanks Emergency pressure relief valve; EN 16249, Tanks for the transport of dangerous goods Service equipment Cap for the adaptor for

28、 bottom loading and unloading; EN 16257, Tanks for the transport of dangerous goods Service equipment Footvalve sizes other than 100 mm dia (nom); EN 16522, Tanks for transport of dangerous goods Service equipment for tanks Flame arresters for breather devices. According to the CEN-CENELEC Internal

29、Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Irelan

30、d, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 14595:2016-10EN 14595:2016 (E) 5 Introduction The breather device as specified includes a safety device to prevent the

31、 contents from spilling out if the tank overturns. The breather may be a separate device, or an integral part of another device. Where the breather device is separate from the safety device (to prevent the contents from spilling out of the tank), the functional performance of these elements in combi

32、nation is required in order to comply with this standard. Where a flame arrestor is required, EN 16522, Flame arrestors for breather devices, specifies requirements. DIN EN 14595:2016-10EN 14595:2016 (E) 6 1 Scope This European Standard covers the breather device used to ensure normal tank compartme

33、nt breathing. It specifies the performance requirements and the critical dimensions of the breather device. It also specifies the tests necessary to verify compliance of the equipment with this document. The service equipment specified by this document is suitable for use with liquid petroleum produ

34、cts and other dangerous substances of Class 3 of ADR 1 which have a vapour pressure not exceeding 110 kPa (absolute) at 50 C and petrol, and which have no sub-classification as toxic or corrosive. 2 Normative references The following documents, in whole or in part, are normatively referenced in this

35、 document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12266-1:2012, Industrial valves - Testing of metallic valves - Part 1: Pressure test

36、s, test procedures and acceptance criteria - Mandatory requirements EN 14564, Tanks for transport of dangerous goods - Terminology EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1) EN 60529, Degrees of prot

37、ection provided by enclosures (IP Code) ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 14564 app

38、ly. 4 Functions The breather device: shall provide pressure and vacuum breathing for a tank compartment, may provide venting where a specific venting device is not fitted, and shall prevent the spilling out of the contents of the tank in the event of an overturn. 5 Design characteristics 5.1 General

39、 Breather devices shall be of the re-sealing type and may or may not breathe or vent directly to atmosphere. They shall be designed to prevent unauthorized adjustment of the relieving pressure settings. The functions described in Clause 4 may be provided by one combined device or by separate indepen

40、dent devices. Discrete devices that are not mounted externally shall have a secondary positive means for being secured. DIN EN 14595:2016-10EN 14595:2016 (E) 7 5.2 Ingress protection The breather device shall be designed, or provision made, to meet the requirements of IP31 in accordance with EN 6052

41、9. 5.3 Pressure ratings 5.3.1 Above atmospheric relieving pressure (pressure relief) Breather devices shall have a relieving pressure of not more than 12 kPa(gauge) in their normally installed attitude. 5.3.2 Below atmospheric relieving pressure (vacuum) The relieving pressure of breather devices sh

42、all be between 0,4 kPa (gauge) and 2,5 kPa (gauge) in their normally installed attitude. 5.3.3 Tank overturn The breather device shall be designed to prevent the spilling out of the contents of the tank in the event of an overturn. 5.4 Flow capacity The flow capacity shall be the flow rate (in m3/h)

43、 of air (at 20 C) achieved by the breather device at the following pressures: pressure flow capacity: 30 kPa above pressure relieving pressure; vacuum flow capacity: 3 kPa below vacuum relieving pressure. 5.5 Temperature range Unless otherwise specified, the design temperature range shall be 20 C to

44、 +50 C. Where the breather device is subjected to more severe conditions, the design temperature range shall be extended to 40 C or +70 C as applicable. 5.6 Materials of construction The manufacturer shall provide, with the equipment, a full material specification for those parts that may come into

45、contact with the substances described in Clause 1. 5.7 Dimensional characteristics When the breather device is provided with threaded connections, the threads shall conform to EN ISO 228-1. 5.8 Electrical resistance The electrical resistance between any conductive part of the device which may come i

46、nto contact with the dangerous goods and its mounting shall not exceed 1 M. 6 Tests 6.1 General Two classes of tests are required: production tests and type tests. Testing methods and procedures shall conform to EN 12266-1 except as specified within this document. DIN EN 14595:2016-10EN 14595:2016 (

47、E) 8 Unless otherwise specified, test fluids shall be air or other suitable gas. The choice of the fluid is the responsibility of the manufacturer. Tests shall be performed on the complete breather device. 6.2 Production tests 6.2.1 General The number, frequency and sampling methods of production te

48、st samples shall be not less than those specified within ISO 2859-1 (AQL of 2,5). Production tests shall comprise the following: seat tightness test (EN 12266-1:2012, A.4); and overturn seat tightness test (EN 12266-1:2012, A.4). 6.2.2 Seat tightness test 6.2.2.1 Test procedure With the device under

49、 test positioned in its normally installed attitude, and closed in a leak -tight condition, a steadily increasing differential test pressure from 0 kPa to the relieving pressure shall be applied. At the devices specified relieving pressure, the differential test pressure shall be held for a time period in accordance with EN 12266-1:2012, Table A.4. During