DIN EN 14587-3-2013 Railway applications Track Flash butt welding of rails Part 3 Welding in association with crossing construction German version EN 14587-3 2012《轨道交通 轨道 导轨闪光对焊 第3.pdf

《DIN EN 14587-3-2013 Railway applications Track Flash butt welding of rails Part 3 Welding in association with crossing construction German version EN 14587-3 2012《轨道交通 轨道 导轨闪光对焊 第3.pdf》由会员分享，可在线阅读，更多相关《DIN EN 14587-3-2013 Railway applications Track Flash butt welding of rails Part 3 Welding in association with crossing construction German version EN 14587-3 2012《轨道交通 轨道 导轨闪光对焊 第3.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、January 2013 Translation by DIN-Sprachendienst.English price group 19No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 25.160.10; 93.100!$uW“1938252www.din.deDDIN EN 14587-3Railway applications - Track Flash butt welding of rails Part 3: Welding in association with crossing construction;English version EN 14587-3:2012,English translation of DIN EN 14587-3:2013-01Bahnanwendungen - Oberbau Abbrennstumpfschweien von

3、Schienen Teil 3: Schweien im Zusammenhang mit Herzstckkonstruktionen;Englische Fassung EN 14587-3:2012,Englische bersetzung von DIN EN 14587-3:2013-01Applications ferroviaires - Voie Soudage des rails par tincelage Partie 3: Soudure associe la fabrication des coeurs de voie;Version anglaise EN 14587

4、-3:2012,Traduction anglaise de DIN EN 14587-3:2013-01www.beuth.deDocument comprises 44 pagesIn case of doubt, the German-language original shall be considered authoritative.01.13DIN EN 14587-3:2013-01 2 A comma is used as the decimal marker. National foreword This document (EN 14587-3:2012) has been

5、 prepared by Technical Committee CEN/TC 256 “Railway applications” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Fahrweg und Schienenfahrzeuge (Railway Standards Committee), Working Committee NA 087-00-01-01 UA Schienenschweien. EUROPEAN

6、 STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14587-3 September 2012 ICS 25.160.10; 93.100 English Version Railway applications - Track - Flash butt welding of rails - Part 3: Welding in association with crossing construction Applications ferroviaires - Voie - Soudage des rails par tincelage - Partie

7、 3: Soudure associe la fabrication des coeurs de voie Bahnanwendungen - Oberbau - Abbrennstumpfschweien von Schienen - Teil 3: Schweien im Zusammenhang mit Herzstckkonstruktionen This European Standard was approved by CEN on 6 July 2012. CEN members are bound to comply with the CEN/CENELEC Internal

8、Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

9、member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official version

10、s. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pol

11、and, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form

12、 and by any means reserved worldwide for CEN national Members. Ref. No. EN 14587-3:2012: EContents Page Foreword 4Introduction .51 Scope 62 Normative references 63 Terms and definitions .64 Information to be supplied for approval of procedure.84.1 By the purchaser84.2 By the manufacturer 85 Approval

13、 of the manufacturer 85.1 General 85.2 Welding procedure 85.3 Operators 95.4 Supervision 95.5 Weld Inspection .95.6 Equipment 95.7 Quality assurance 96 Requirements for the welding process .96.1 General 96.2 Workpiece preparation 96.3 Clamping force 106.4 Initial burn-off 106.5 Preheating . 106.6 Fi

14、nal flashing . 106.7 Upsetting . 106.8 Post-weld treatment 116.8.1 Before unclamping . 116.8.2 After removal from machine 116.9 Welding parameters . 116.10 Removal of upset and correction of weld alignment 117 Profile finishing of the weld . 118 Weld geometry and dimensions 128.1 General . 128.2 Ali

15、gnment and flatness across the weld 128.3 Foot dimensions . 139 Weld identification 1310 Procedure approval 1310.1 General . 1310.2 Test weld specimen preparation . 1410.3 Number of specimens 1410.4 Approval tests . 1410.4.1 General . 1410.4.2 Weld geometry and dimensions 1410.4.3 Visual inspection

16、1410.4.4 Surface finish 1410.4.5 Liquid penetrant testing and magnetic particle testing 1410.4.6 Internal soundness . 1510.4.7 Bend testing 1510.4.8 Fatigue testing 1510.4.9 Macro-examination . 15DIN EN 14587-3:2013-01 EN 14587-3:2012 (E) 210.4.10 Micro-examination . 1610.4.11 Hardness testing 1610.

17、5 Test result report . 1710.6 Validity of approval 1711 Approval of other rail profiles or grades . 1711.1 General 1711.2 Sample preparation . 1711.3 Approval tests 1711.4 Test result report . 1812 Track trials 1812.1 General 1812.2 Track trial test result report 1813 Weld production following proce

18、dure approval . 1813.1 Weld production 1813.2 Weld parameter monitoring 1813.3 Visual inspections . 1813.4 Weld geometry and dimensions 1913.5 Liquid penetrant testing and magnetic particle testing . 1913.6 Internal soundness 1913.7 Bend Testing 1913.7.1 General 1913.7.2 Additional test requirements

19、 1913.7.3 Bend test procedure 1913.7.4 Interpretation of results 2013.7.5 Retesting 2013.7.6 Documentation . 20Annex A (informative) Example of Flat spot and Bright spot . 21Annex B (normative) Bend test requirements 22Annex C (normative) Test weld fracture faces Recording of defects . 24Annex D (no

20、rmative) Fatigue test method for flash butt welds . 26D.1 Scope 26D.2 Test equipment 26D.3 Calibration procedure . 28D.3.1 General 28D.3.2 Test piece . 28D.3.3 Test piece preparation 28D.3.4 Instrumentation 28D.3.5 Procedure . 28D.4 Fatigue test method . 32D.4.1 General 32D.4.2 Staircase testing met

21、hod 32D.4.3 Example of the data analysis of a fatigue strength determination by the staircase method 35D.4.4 Past-the-post testing method . 35Annex E (normative) Macro-examination and micro-examination. 37E.1 Macro examination 37E.2 Micro examination . 37Annex F (normative) Hardness testing . 39Anne

22、x G (normative) Ultrasonic testing non-austenitic materials . 40G.1 Reference line (DAC) generation Reference block . 40G.2 Reference line (DAC) generation and acceptance criteria 40Bibliography 42DIN EN 14587-3:2013-01EN 14587-3:2012 (E) 3 Foreword This document (EN 14587-3:2012) has been prepared

23、by Technical Committee CEN/TC 256 “Railway applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2013, and conflicting national standards sh

24、all be withdrawn at the latest by March 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a

25、mandate given to CEN by the European Commission and the European Free Trade Association. This document is one of a series of three parts of the EN 14587 “Railway applications Track Flash butt welding of rails”. The list of parts is as follows: Part 1: New R220, R260, R260Mn and R350HT grade rails in

26、 a fixed plant Part 2: New R220, R260, R260Mn and R350HT grade rails by mobile welding machines at sites other than a fixed plant Part 3: Welding in association with crossing construction (the present standard) According to the CEN/CENELEC Internal Regulations, the national standards organisations o

27、f the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Net

28、herlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 14587-3:2013-01 EN 14587-3:2012 (E) 4Introduction This part of EN 14587 has four main topics: requirements of a welding process; procedure approval for a fixed plant; ap

29、proval of other rail profiles or grades; weld production following approval. This European Standard satisfies the needs of the railway authority. The manufacturer should achieve the specified requirements of this European Standard. DIN EN 14587-3:2013-01EN 14587-3:2012 (E) 5 1 Scope This European St

30、andard specifies requirements for the approval of a welding process in a fixed plant, together with the requirements for subsequent welding production. This European Standard applies to new Vignole rails welded by flash butt welding to crossing components in a fixed plant, and intended for use on ra

31、ilway infrastructures. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docume

32、nt (including any amendments) applies. EN 571-1, Non-destructive testing Penetrant testing Part 1: General principles EN 1371-1, Founding Liquid penetrant testing Part 1: Sand, gravity die and low pressure die castings EN 13674-1, Railway applications Track Rail Part 1: Vignole railway rails 46 kg/m

33、 and above EN 13674-2, Railway applications Track Rail Part 2: Switch and crossing rails used in conjunction with Vignole railway rails 46 kg/m and above EN 13674-4, Railway applications Track Rail Part 4: Vignole railway rails from 27 kg/m to, but excluding 46 kg/m EN 14587-1:2007, Railway applicat

34、ions Track Flash butt welding of rails Part 1: New R220, R260, R260Mn and 350HT grade rails in a fixed plant EN ISO 6507-1, Metallic materials Vickers hardness test Part 1: Test method (ISO 6507-1) EN ISO 11666, Non-destructive testing of welds Ultrasonic testing Acceptance levels (ISO 11666) EN ISO

35、 17638, Non-destructive testing of welds Magnetic particle testing (ISO 17638) EN ISO 17640, Non-destructive testing of welds Ultrasonic testing Techniques, testing levels, and assessment (ISO 17640) EN ISO 23279, Non-destructive testing of welds Ultrasonic testing Characterization of indications in

36、 welds (ISO 23279) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 manufacturer company that joins rails to rails, rails to crossings and rails to crossing components by flash butt welding in a fixed plant 3.2 purchaser buyer of the flashbutt

37、 welded crossings working in accordance with the requirements of the railway authority 3.3 railway infrastructure permanent way of national or private railways DIN EN 14587-3:2013-01 EN 14587-3:2012 (E) 63.4 fixed plant stationary machine for flash butt welding of rails to rails, rails to crossings

38、and rails to crossing components 3.5 die burn damage caused by localised overheating on the electrode contact surfaces 3.6 upset metal extruded around the rail profile as a result of forging 3.7 specimen portion detached from a welded component or a welded joint and prepared as required for testing

39、3.8 profile finishing operation by which the rail or relevant part of the component at the weld is returned to original profile, by removal of upset material Note 1 to entry: This operation can be achieved by grinding, milling, planing or any other suitable means. 3.9 finished condition welded and p

40、rofile finished 3.10 flat spot feature having a localised smooth texture when viewed in a vertical transverse section (see Annex A) Note 1 to entry: When viewed longitudinally in macro this may appear as a lens-shaped feature. 3.11 bright spot localised bright area occurring at the stainless insert/

41、rail interface indicative of a possible martensitic area (see Annex A) 3.12 lack of bond area within the weld where there is no metal to metal contact (excluding flat spots and bright spots) Note 1 to entry: This may appear as a linear discontinuity at the interfaces when examined in the finished co

42、ndition or after sectioning. 3.13 welded zone areas of 50 mm on either side of the weld centreline 3.14 throat flare wing entry flare (front) machining or setting of wings to give an entry flare into the throat 3.15 foundry method system to produce casting compliant with the requirements of EN 15689

43、 3.16 workpiece crossing component, insert rail or rail leg-end extension DIN EN 14587-3:2013-01EN 14587-3:2012 (E) 7 3.17 railway authority (RA) either the railway regulator or the owner of the railway infrastructure or the custodian with a delegated responsibility for a railway infrastructure 3.18

44、 as welded condition rails that have been welded and trimmed only 4 Information to be supplied for approval of procedure 4.1 By the purchaser The following information shall be supplied by the purchaser, agreed upon by the manufacturer, and shall be fully documented: a) the rail profile and crossing

45、 geometrical details; b) the rail and crossing grades/materials; c) the profile class of the rail leg-end extension as specified in EN 13674-1, EN 13674-2 or EN 13674-4; d) alignment class/classes of the flash butt welds (see Table 1); e) the type of fatigue tests (if applicable) for approval; f) to

46、lerances at rail ends on the delivered crossing; g) minimum length of rail leg-end extension; h) rail profile, number and frequency of production bend tests (see 13.7); i) requirements of any track trials. 4.2 By the manufacturer The following information shall be supplied by the manufacturer, agree

47、d upon by the purchaser, and shall be fully documented: a) a qualified weld procedure; b) traceability system of the welds; c) type and identification number of machine being used. 5 Approval of the manufacturer 5.1 General The manufacturer shall meet the approval requirements as defined in 5.2 to 5

48、.7. The purchaser reserves the right to audit the manufacturer at any time. 5.2 Welding procedure The manufacturer shall use welding procedures and flash butt welding machines that are approved by the RA. DIN EN 14587-3:2013-01 EN 14587-3:2012 (E) 85.3 Operators The manufacturer shall maintain a system that ensures the competence of their welding operat