DIN EN 14318-1-2013 Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1 Specification fo.pdf

《DIN EN 14318-1-2013 Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1 Specification fo.pdf》由会员分享，可在线阅读，更多相关《DIN EN 14318-1-2013 Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1 Specification fo.pdf（66页珍藏版）》请在麦多课文档分享上搜索。

1、April 2013 Translation by DIN-Sprachendienst.English price group 24No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、91.100.60!$|E“1988934www.din.deDDIN EN 14318-1Thermal insulating products for buildings In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate(PIR) foam products Part 1: Specification for the rigid foam dispensed system beforeinstallation;English version EN 14318-1:2013,English trans

3、lation of DIN EN 14318-1:2013-04Wrmedmmstoffe fr das Bauwesen An der Verwendungsstelle hergestellter Wrmedmmstoff aus dispensiertem Polyurethan(PUR)- und Polyisocyanurat (PIR)-Hartschaum Teil 1: Spezifikation fr das Schaumsystem vor dem Einbau;Englische Fassung EN 14318-1:2013,Englische bersetzung v

4、on DIN EN 14318-1:2013-04Produits isolants thermiques destins aux applications du btiment Produits en mousse rigide de polyurthanne (PUR) ou de polyisocyanurate (PIR) injecte,forms en place Partie 1: Spcifications relatives aux systmes dinjection de mousse rigide avant mise enoeuvre;Version anglaise

5、 EN 14318-1:2013,Traduction anglaise de DIN EN 14318-1:2013-04Together with DIN EN 14315-1:2013-04, DIN EN 14315-2:2013-04, DIN EN 14318-2:2013-04,DIN EN 14319-1:2013-04, DIN EN 14319-2:2013-04, DIN EN 14320-1:2013-04 and DIN EN 14320-2:2013-04supersedes DIN 18159-1:1991-12See start of applicationSu

6、persedes: see belowwww.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 66 pages 03.13 DIN EN 14318-1:2013-04 2 A comma is used as the decimal marker. Start of application It should be noted that, in Germany, CE conformity marking of constru

7、ction products will be permitted once this standard has been listed in the Official Journal of the European Union and/or the Bundesanzeiger (German Federal Gazette) and from the date given therein. For further information, users of this standard should refer to the websites of the European Commissio

8、n or of the relevant building authority. The standard which this document replaces, DIN 18159-1:1991-12, may be used in parallel with this standard during a specified transition period where such has been laid down in the Official Journal of the European Union and/or the Bundesanzeiger (German Feder

9、al Gazette). National foreword This document (EN 14318-1:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products” (Secretariat: DIN, Germany), Working Group WG 15 “In situ formed insulation products” (lead-management: BSI, United Kingdom). The responsible

10、German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-56-60 AA Wrmedmmstoffe. This document is part of a package of interrelated standards for the specification of factory made thermal insulation produc

11、ts. Amendments This standard differs from DIN 18159-1:1991-12 as follows: a) EN 14318-1 supersedes DIN 18159-1:1991-12 covering in-situ polyurethane (PUR) foam applied by pouring. Previous editions DIN 18159-1: 1978-06, 1991-12 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14318-1 January 201

12、3 ICS 91.100.60 English Version Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam dispensed system before installation Produits isolants thermiques destins aux applications

13、 du btiment - Produits en mousse rigide de polyurthanne (PUR) ou de polyisocyanurate (PIR) injecte, forms en place - Partie 1 : Spcifications relatives aux systmes dinjection de mousse rigide avant mise en uvre Wrmedmmstoffe fr das Bauwesen - An der Verwendungsstelle hergestellter Wrmedmmstoff aus d

14、ispensiertem Polyurethan (PUR)- und Polyisocyanurat (PIR)-Hartschaum - Teil 1: Spezifikation fr das Schaumsystem vor dem Einbau This European Standard was approved by CEN on 17 November 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for

15、 giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three

16、 official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodi

17、es of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Sp

18、ain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN n

19、ational Members. Ref. No. EN 14318-1:2013: EEN 14318-1:2013 (E) 2 Contents Page Foreword . 4 1 Scope 5 2 Normative references . 5 3 Terms, definitions, symbols and abbreviations 6 3.1 Terms and definitions 6 3.2 Symbols and abbreviations . 8 4 Requirements . 9 4.1 General . 9 4.2 For all application

20、s . 10 4.3 Specific applications 12 5 Test methods 14 5.1 Sampling and test specimen preparation . 14 5.2 Conditioning . 14 5.3 Testing 14 6 Designation code . 16 7 Evaluation of conformity 16 7.1 General . 16 7.2 Initial type testing . 17 7.3 Factory production control 17 8 Marking, labelling and t

21、echnical information 17 8.1 Marking and labelling . 17 8.2 Technical information 17 Annex A (normative) Determination of declared aged thermal conductivity and aged thermal resistance . 19 A.1 Introduction 19 A.2 Input data 19 A.3 Declared values 19 Annex B (normative) Determination of substrate adh

22、esion strength perpendicular to faces . 21 B.1 Principle 21 B.2 Apparatus . 21 B.3 Test specimen 21 B.4 Procedure . 21 B.5 Report . 22 Annex C (normative) Determination of the aged values of thermal resistance and thermal conductivity 23 C.1 General . 23 C.2 Sampling and test specimen preparation .

23、23 C.3 Determination of the initial value of thermal conductivity . 24 C.4 Determination of the accelerated aged value of thermal conductivity 25 C.5 Fixed increment procedure 27 C.6 Declaration of the aged values of thermal resistance and aged thermal conductivity . 29 Annex D (normative) Initial t

24、ype testing (ITT) and Factory production control (FPC) . 31 Annex E (normative) Determination of the reaction profile and free-rise density 33 E.1 Introduction 33 E.2 Principle 33 E.3 Apparatus . 33 E.4 Procedure . 33 DIN EN 14318-1:2013-04 EN 14318-1:2013 (E) 3 E.5 Free-rise density . 34 Annex F (n

25、ormative) Sample preparation method for the test specimens for the thermal conductivity test . 35 Annex G (normative) Sample preparation method for the test specimens other than thermal conductivity 36 G.1 Principle 36 G.2 Procedure . 36 Annex H (normative) Testing for reaction to fire of products .

26、 37 H.1 Scope 37 H.2 Product and installation parameters . 37 H.3 Mounting and fixing . 38 H.4 Field of application . 40 Annex I (normative) Testing for reaction to fire of products in standardised assemblies simulating end-use application(s) . 42 I.1 Scope 42 I.2 Product and installation parameters

27、 . 42 I.3 Mounting and fixing . 43 I.4 Field of application . 46 Annex J (informative) Example for the determination of the declared aged values of thermal conductivity and thermal resistance for a product . 48 Case where both thermal conductivity and thermal resistance are declared 48 Annex K (norm

28、ative) Instructions for compiling thermal resistance performance charts. 50 K.1 Introduction 50 K.2 General . 50 K.3 Procedure for the manufacturer to create the performance charts . 52 Annex ZA (informative) Clause of this European Standard addressing the provisions of the provisions of the EU Cons

29、truction Products Directive 57 ZA.1 Scope and relevant characteristics . 57 ZA.2 Procedure for attestation of conformity of in-situ formed dispensed rigid polyurethane (PUR) and rigid polyisocyanurate foam (PIR) products 59 ZA.3 CE marking and labelling . 62 Bibliography 64 DIN EN 14318-1:2013-04 EN

30、 14318-1:2013 (E) 4 Foreword This document (EN 14318-1:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an i

31、dentical text or by endorsement, at the latest by July 2013, and conflicting national standards shall be withdrawn at the latest by July 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held re

32、sponsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Ann

33、ex ZA, which is an integral part of this document. This European Standard consists of two parts which form a package. The first part is the harmonised part satisfying the mandate and the CPD and is the basis for the CE marking covering the products, which are placed on the market. The second part, w

34、hich is the non-harmonised part, covers the specification for the installed products. Both parts need to be used for the application of the insulation product in the end-use applications covered by EN 14318. This European Standard is one of a series for mineral wool, expanded clay, expanded perlite,

35、 exfoliated vermiculite, polyurethane/polyisocyanurate, cellulose, bound expanded polystyrene and expanded polystyrene in-situ formed insulation products used in buildings, but this standard may be used in other areas where appropriate. The reduction in energy used and emissions produced during the

36、installed life of insulation products exceeds by far the energy used and emissions made during the production and disposal processes. This European Standard, EN 14318-1, Thermal insulating products for buildings In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam produc

37、ts, consists of the following parts: Part 1: Specification for the rigid foam dispensed system before installation (the present document) Part 2: Specification for the installed insulation products According to the CEN/CENELEC Internal Regulations, the national standards organisations of the followi

38、ng countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Nor

39、way, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 14318-1:2013-04 EN 14318-1:2013 (E) 5 1 Scope This European Standard specifies requirements for in-situ formed dispensed rigid polyurethane (PUR) and rigid polyisocyanurate (PIR) foa

40、m products when installed into cavity walls. This Part 1 of this European Standard is a specification for the rigid foam dispensing system before installation. Part 1 of this European Standard describes the product characteristics and includes procedures for testing, marking and labelling and the ru

41、les for evaluation of conformity. This European Standard does not specify the required levels of all properties that should be achieved by a product to demonstrate fitness for purpose in a particular end-use application. The required levels are to be found in regulations or non-conflicting standards

42、. This European Standard does not cover factory made rigid polyurethane (PUR) or polyisocyanurate (PIR) foam insulation products or in-situ products intended to be used for the insulation of building equipment and industrial installations. NOTE Foam products are either called flexible or rigid. The

43、flexible products are used in upholstery and mattresses and are characterised by their ability to deflect, support and recover to their original thickness continually during their in-use phase. Those that are not flexible are termed rigid and do not possess these flexible characteristics. They are m

44、ostly used for thermal insulation purposes and vary widely in their compression strength values. Once the cell structure is crushed in a rigid foam, it does not recover its thickness fully. Some of these rigid foams are very low in density with very low compression strengths and are sometimes descri

45、bed “commercially” as “soft foams” or “semi-rigid” foams. This note has been included to clarify that all foams with such descriptions are covered by this standards used of the term rigid foam. 2 Normative references The following documents, in whole or in part, are normatively referenced in this do

46、cument and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 312, Particleboards Specifications EN 508-1, Roofing products from metal sheet Specific

47、ation for self-supporting products of steel, aluminium or stainless steel sheet Part 1: Steel EN 520, Gypsum plasterboards Definitions, requirements and test methods EN 823, Thermal insulating products for building applications Determination of thickness EN 1602, Thermal insulating products for buil

48、ding applications Determination of the apparent density EN 1604, Thermal insulating products for building applications Determination of dimensional stability under specified temperature and humidity conditions EN 1609, Thermal insulating products for building applications Determination of short term water absorption by partial immersion EN 12086:1997, Thermal insulating products for building applications Determination of water vapour transmission properties EN 12667:2001, Thermal performance of bui