DIN EN 14159-2015 Textile floor coverings - Requirements for tolerances on (linear) dimensions of rugs runners carpet tiles and wall-to-wall carpet and for tolerances on pattern re.pdf

《DIN EN 14159-2015 Textile floor coverings - Requirements for tolerances on (linear) dimensions of rugs runners carpet tiles and wall-to-wall carpet and for tolerances on pattern re.pdf》由会员分享，可在线阅读，更多相关《DIN EN 14159-2015 Textile floor coverings - Requirements for tolerances on (linear) dimensions of rugs runners carpet tiles and wall-to-wall carpet and for tolerances on pattern re.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、March 2015 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 5

2、9.080.60!%AR9“2304722www.din.deDDIN EN 14159Textile floor coverings Requirements for tolerances on (linear) dimensions of rugs, runners,carpet tiles and wall-to-wall carpet and for tolerances on pattern repeat;English version EN 14159:2014,English translation of DIN EN 14159:2015-03Textile Bodenbelg

3、e Anforderungen an Toleranzen der (linearen) Mae von abgepassten Bodenbelgen,Lufern, Fliesen und Bahnenware und des Musterrapports;Englische Fassung EN 14159:2014,Englische bersetzung von DIN EN 14159:2015-03Revtements de sol textiles Exigences relatives aux tolrances sur les dimensions (linaires) d

4、es tapis, passages,dalles de moquette et moquettes et aux tolrances sur le raccord de dessin;Version anglaise EN 14159:2014,Traduction anglaise de DIN EN 14159:2015-03SupersedesDIN CEN/TS 14159:2007-07www.beuth.deDocument comprises 14 pagesIn case of doubt, the German-language original shall be cons

5、idered authoritative.03.15 DIN EN 14159:2015-03 2 A comma is used as the decimal marker. National foreword This document (EN 14159:2014) has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” (Secretariat: NBN, Belgium). The responsible German body invo

6、lved in its preparation was the DIN-Normenausschuss Kunststoffe (DIN Standards Committee Plastics), Working Committee NA 054-04-09 AA Textile Bodenbelge. Amendments This standard differs from DIN CEN/TS 14159:2007-07 as follows: a) in the German version, the terms Teppich-Auslegware (wall-to-wall ca

7、rpet) and Teppichrolle (carpet roll) have been replaced by Bahnenware (wall-to-wall carpet); b) in the German version, the terms Teppich (carpet) and Webteppich (woven carpet) have been replaced by Bodenbelag (rug) and gewebter Bodenbelag (woven carpet); c) in the German version, the term Teppichfli

8、ese (carpet tile) has been replaced by Fliese (carpet tile); d) the figures have been allocated to the relevant clauses; e) the standard has been editorially revised. Previous editions DIN CEN/TS 14159: 2005-03, 2007-07 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14159 December 2014 ICS 59.

9、080.60 Supersedes CEN/TS 14159:2007English Version Textile floor coverings - Requirements for tolerances on (linear) dimensions of rugs, runners, carpet tiles and wall-to-wall carpet and for tolerances on pattern repeat Revtements de sol textiles - Exigences relatives aux tolrances sur les dimension

10、s (linaires) des tapis, passages, dalles de moquette et moquettes et aux tolrances sur le raccord de dessin Textile Bodenbelge - Anforderungen an Toleranzen der (linearen) Mae von abgepassten Bodenbelgen, Lufern, Fliesen und Bahnenware und des Musterrapports This European Standard was approved by CE

11、N on 16 November 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standar

12、ds may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and noti

13、fied to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Ic

14、eland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Man

15、agement Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14159:2014 EEN 14159:2014 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definiti

16、ons .5 4 Apparatus .6 4.1 Length measuring device .6 4.2 Dividers .6 4.3 Drawing device .6 5 Procedure .6 5.1 Measurement of dimensions 6 5.2 Measurement of pattern distortion 6 5.2.1 General 6 5.2.2 Distortion in pattern repeat .6 5.2.3 Bowing 7 5.2.4 Linear pattern distortion .8 5.2.5 Skewing of p

17、attern .9 5.2.6 Arcing 9 6 Required tolerances and deviations . 10 6.1 Dimensions 10 6.2 Pattern repeat and distortion . 11 6.3 Arcing of the carpet roll . 11 Bibliography . 12 DIN EN 14159:2015-03 EN 14159:2014 (E) 3 Foreword This document (EN 14159:2014) has been prepared by Technical Committee CE

18、N/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2015 and conflicting national standards sh

19、all be withdrawn at the latest by June 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TS 14159:200

20、7. In comparison with CEN/TS 14159:2007, the document has been revised editorially. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Rep

21、ublic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN

22、 EN 14159:2015-03 EN 14159:2014 (E) 4 Introduction Owing to influences of the production process on the structure, textile floor coverings may show variations in size and distortion. However, in many cases, certain discrepancies can be eliminated by professional and careful installation. By open com

23、munication between manufacturer and installer, an agreement can be found between what is technically possible in manufacturing, and at the same time technically workable during installation. The maximum distortions in pattern repeat specified in this European Standard are applicable only to carpets

24、with certain design styles ex-factory. DIN EN 14159:2015-03 EN 14159:2014 (E) 5 1 Scope This European Standard specifies the maximum accepted tolerances on the dimensions and distortions in pattern, of rugs, runners, carpet tiles and wall-to-wall carpet. NOTE These tolerances do not affect the funct

25、ional characteristics of the textile floor covering. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest ed

26、ition of the referenced document (including any amendments) applies. ISO 2424:2007, Textile floor coverings Vocabulary ISO 3018, Textile floor coverings Rectangular textile floor coverings Determination of dimensions 3 Terms and definitions For the purposes of this document, the terms and definition

27、s given in ISO 2424:2007 and the following apply. 3.1 arcing arcing of the carpet roll itself in the production direction when unrolled Note 1 to entry: See Figure 5. 3.2 linear pattern distortion displacements of the pattern widthways so that alignment of repeated design features in the production

28、direction are not parallel with the edge of the carpet Note 1 to entry: See Figure 3. 3.3 bowing displacement of the pattern alignment across the width of the carpet so that repeated design features are displaced from a line at right angles to the direction of production Note 1 to entry: This displa

29、cement is usually at its greatest extent in the centre of the carpet width. Note 2 to entry: See Figure 2. 3.4 length linear dimension of the longest side 3.5 length linear dimension parallel to the direction of production 3.6 pattern repeat smallest part of the pattern that contains all its charact

30、eristics DIN EN 14159:2015-03 EN 14159:2014 (E) 6 3.7 skewing situation in which lines drawn through repeated design features both parallel to and perpendicular to the production direction are not at right angles to each other Note 1 to entry: See Figure 4. 3.8 width linear dimension of the shortest

31、 side 3.9 width linear dimension at right angles to the production direction 4 Apparatus 4.1 Length measuring device The device shall be capable of measuring to an accuracy of for dimensions 1,0 m: 1 mm. for dimensions 1,0 m and 5,0 m: 5 mm. for dimensions 5,0 m: 10 mm. 4.2 Dividers 4.3 Drawing devi

32、ce The device shall be capable of describing a datum line across the width of the carpet at 90 to the edge of the carpet. 5 Procedure 5.1 Measurement of dimensions Lay the rug or carpet roll out flat, use surface uppermost. Use the length measuring device (4.1) and the dividers (4.2), if appropriate

33、, to measure the length (Ix) and the width, (ly), in accordance with ISO 3018. 5.2 Measurement of pattern distortion 5.2.1 General Each of the following measurements can be made either on the face (tufted carpet) or back (woven carpet) of the unrolled carpet. 5.2.2 Distortion in pattern repeat Measu

34、re the distortion in pattern repeat length as the distance between a line drawn across the carpet at the maximum extent of the pattern (l1), and an equivalent line drawn across the carpet at the minimum extent of the corresponding pattern (l2). Figure 1 shows an example of measurement of the distort

35、ion in pattern repeat length. Measure the maximum deviation to the appropriate accuracy (see 4.1) over n pattern repeats and over a length of at least 1 m. DIN EN 14159:2015-03 EN 14159:2014 (E) 7 The distortion (mm) is given by (l2- l1). The measurements should be repeated in a number of positions

36、throughout the carpet and all results quoted. Figure 1 Pattern repeat 5.2.3 Bowing Use the device described in 4.3 to draw a line perpendicular to the machine direction edge of the carpet. The line should be drawn perpendicular to the edge at a convenient reference point, i.e. one particular part of

37、 the pattern repeat that can be traced across the width of the carpet. Use the length measuring device (4.1) and dividers (4.2) to measure the maximum deflection (aq) to the appropriate accuracy (see 4.1), as shown in Figure 2. The measurements should be repeated in a number of positions throughout

38、the carpet and all results quoted. DIN EN 14159:2015-03 EN 14159:2014 (E) 8 Figure 2 Bowing 5.2.4 Linear pattern distortion Repeat the method given in 5.2.3 across the width of the carpet, i.e. measure the deflection from a line drawn parallel to the machine direction edge of the carpet. Measure the

39、 maximum deflection (a) of the pattern to the appropriate accuracy (see 4.1), as shown in Figure 3. The measurements should be repeated in a number of positions throughout the carpet and all results quoted. Figure 3 Linear pattern distortion DIN EN 14159:2015-03 EN 14159:2014 (E) 9 5.2.5 Skewing of

40、pattern Use the device described in 4.3 to draw a line perpendicular to the production direction from a specific point on the pattern at one machine edge of the carpet to the opposite machine edge of the carpet. Use the length measuring device to measure the pattern deviation (ad) to the appropriate

41、 accuracy (see 4.1), as shown in Figure 4. The measurements should be repeated in a number of positions throughout the carpet and all results quoted. Figure 4 Skewing 5.2.6 Arcing Draw a perpendicular to one of the cross machine directions of the carpet and continue for the full length of the carpet

42、. Draw a line to continue to the opposite cross machine width until it dissects the perpendicular. Measure the maximum deviation (awo) as shown in Figure 5, to the nearest 1,0 mm. DIN EN 14159:2015-03 EN 14159:2014 (E) 10 Figure 5 Maximum deviations of the arcing of the carpet roll 6 Required tolera

43、nces and deviations 6.1 Dimensions Tolerances on the dimensions of textile floor coverings (rugs, runners, tiles and carpet roll) shall conform to those specified in Table 1. Table 1 Tolerances on dimensions Textile floor covering type Width Length a) Rugs and runners nominal width 2,0 % nominal len

44、gth 2,0 % b) Wall-to-wall carpets 1) stock products i) woven carpets ii) other carpets 2) special order nominal width 1,25 % nominal width 1,0 % By mutual agreement between producer and customer nominal length 1,0 % nominal length 1,0 % By mutual agreement between producer and customer c) Tiles 0,3

45、% on nominal dimensions 0,2 % within the same batch 0,3 % on nominal dimensions 0,2 % within the same batch DIN EN 14159:2015-03 EN 14159:2014 (E) 11 6.2 Pattern repeat and distortion Table 2 Tolerances for deviations in pattern repeat and distortion Type Deviations on individual measurement Pattern

46、 repeat (Figure 1) Pattern shift between pieces from the same production lot a pattern repeat length between 0 cm and 10,0 cm pattern repeat length between 10,0 cm and 100,0 cm pattern repeat length 100,0 cm accumulated pattern shift max. 2,0 % of the pattern repeat max. 1,0 % of the pattern repeat

47、as quoted by manufacturer max. 0,5 % Bowing (Figure 2) woven carpet 100 cm woven carpet 100 cm and 200 cm woven carpet 200 cm tufted carpet max. 10 mm max. 20 mm max. 30 mm 1,0 % of roll width with a maximum of 10 mm per m of roll width Linear pattern distortion (Figure 3) woven or tufted carpet max

48、imum 10 mm for 2 m nominal length Skewing (Figure 4) woven or tufted carpet maximum 1,0 % of width with a maximum of 10 mm per m of roll width aRolls from different lots with the same pattern should not be installed next to each other. 6.3 Arcing of the carpet roll Maximum deviations of the arcing of the carpet roll (Figure 5) shall conform to those specified in Table 3. Table 3 Deviation of arcing Carpet type Deviation Woven maximum 0,5 % of the piece length