DIN EN 13709-2010 Industrial valves - Steel globe and globe stop and check valves German version EN 13709 2010《工业用阀 钢制球阀、球状截止阀和止回阀 德文版本EN 13709-2010》.pdf

《DIN EN 13709-2010 Industrial valves - Steel globe and globe stop and check valves German version EN 13709 2010《工业用阀 钢制球阀、球状截止阀和止回阀 德文版本EN 13709-2010》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13709-2010 Industrial valves - Steel globe and globe stop and check valves German version EN 13709 2010《工业用阀 钢制球阀、球状截止阀和止回阀 德文版本EN 13709-2010》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、October 2010 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 23.060.10!$kTj“1724971www.din.deDDIN EN 13709Industrial valves Steel globe and globe stop and check valvesEnglish translation of DIN EN 13709:2010-10Industriearmaturen Absperrventile und absperrbare Rckschlagventile aus StahlEnglische bersetzung von DIN EN 13709:2010-10Robinetterie industrielle Ro

3、binets soupape et robinets clapet libre blocable en acierTraduction anglaise de DIN EN 13709:2010-10SupersedesDIN EN 13709:2003-01www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.180 .109 DIN EN 13709:2010-10 A comma is used as the

4、decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 69 “Industrial valves” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Armaturen (Valves Standards Committee), Working Committee NA 003-01-03

5、AA Ventile. Amendments This standard differs from DIN EN 13709:2003-01 as follows: a) normative references in Clause 2 and in Subclauses 4.1.1, 4.1.2, 4.1.3, 4.1.7.1, 4.2.1, 4.2.4 and 5.1 have been updated; b) in Table ZA.1, reference is made to Subclause 4.1 (instead of Clause 4) to take into accou

6、nt Directive 97/23/EC (Pressure Equipment Directive PED), Annex I, Subclause 2.1. Previous editions DIN 3332: 1943-12, 1951x-09 DIN 3356-3: 1982-05 DIN 3356-4: 1982-05 DIN 3356-5: 1982-05 DIN 3790: 1958-04 DIN 3791: 1958-04 DIN EN 13709: 2003-01 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN

7、 13709 May 2010 ICS 23.060.10 Supersedes EN 13709:2002English Version Industrial valves Steel globe and globe stop and check valves Robinetterie industrielle Robinets soupape et robinets clapet libre blocable en acier Industriearmaturen Absperrventile und absperrbare Rckschlagventile aus Stahl This

8、European Standard was approved by CEN on 9 April 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

9、concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into i

10、ts own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, L

11、atvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brus

12、sels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13709:2010: EEN 13709:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions . 54 Requirements . 64.1 Design . 64.1.1 Materials . 64.1.2

13、 Pressure/temperature ratings . 64.1.3 Dimensions . 64.1.4 Operation 84.1.5 Auxiliary connections . 84.1.6 Obturator 104.1.7 Permanent joining 104.2 Functional characteristics 104.2.1 Shell design strength 104.2.2 Flow characteristics 104.2.3 Allowable differential pressure 114.2.4 Seat tightness 11

14、4.2.5 Sizing the operating element 125 Test procedures . 126 Declaration of compliance 127 Designation 128 Marking and preparation for storage and transportation 138.1 Marking . 138.2 Preparation for storage and transportation 13Annex A (informative) Information to be supplied by the purchaser 14Ann

15、ex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC . 15Bibliography 16DIN EN 13709:2010-10 EN 13709:2010 (E) 3 Foreword This document (EN 13709:2010) has been prepared by Technical Committee CEN/TC 69 “Industrial valves”, the secre

16、tariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2010, and conflicting national standards shall be withdrawn at the latest by November 2010. Attention is

17、drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13709:2002. This document has been prepared under a mandate given to CE

18、N by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 97/23/EC. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. This document supersedes EN 13709:2002 where the following mod

19、ifications were made: the normative references were updated in Clause 2, in 4.1.1, in 4.1.2, in 4.1.3, in 4.1.7.1, in 4.2.1, in 4.2.4 and in 5.1; in Table ZA.1, sub-clause 4.1 (instead of Clause 4) was correlated to PED Annex I, section 2.1. According to the CEN/CENELEC Internal Regulations, the nat

20、ional standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands

21、, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 13709:2010-10 EN 13709:2010 (E) 4 1 Scope This European Standard specifies the requirements for steel globe and globe stop and check valves which are wrought, cast or fabricated in stra

22、ight, angle or oblique pattern with end connections flanged, butt welding, socket welding or threaded. This standard is applicable to steel globe and globe stop and check valves mainly used for industrial and general purpose applications. However, they can be used for other applications provided the

23、 requirements of the relevant performance standards are met. The range of nominal sizes covered is: DN 8; DN 10; DN 12; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400. DN 8 and DN 12 are not used for PN designated flanged end co

24、nnections. DN 8, DN 10 and DN 12 are not used for Class designated flanged end connections. Socket welding end valves and threaded end valves are limited to the range DN 8 to DN 65. The range of pressure designations covered is: a) for flanged and butt welding end valves: 1) PN 10; PN 16; PN 25; PN

25、40; PN 63; PN 100; 2) Class 150; Class 300; Class 600. b) for socket welding end valves and threaded end valves: 3) PN 40; PN 63; PN 100; 4) Class 600; Class 800. NOTE Class 800 is a Class designation widely used for socket welding and threaded end valves. 2 Normative references The following refere

26、nced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 19, Industrial valves Marking of metallic valves EN 287-1:2004, Qu

27、alification test of welders Fusion welding Part 1: Steels EN 558, Industrial valves Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems PN and Class designated valves EN 736-1:1995, Valves Terminology Part 1: Definition of types of valves EN 736-2:1997, Valves

28、Terminology Part 2: Definition of components of valves EN 736-3:2008, Valves Terminology Part 3: Definition of terms DIN EN 13709:2010-10 EN 13709:2010 (E) 5 EN 1092-1:2007, Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, PN designated Part 1: Steel flanges EN

29、1418, Welding personnel Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials EN 1759-1, Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, Class designated Part 1: Ste

30、el flanges, NPS to 24 EN 10045-1, Metallic materials Charpy impact test Part 1: Test method EN 12266-1:2003, Industrial valves Testing of valves Part 1: Pressure tests, test procedures and acceptance criteria Mandatory requirements EN 12266-2:2002, Industrial valves Testing of valves Part 2: Tests,

31、test procedures and acceptance criteria Supplementary requirements EN 12351, Industrial valves Protective caps for valves with flanged connections EN 12516-1, Industrial valves Shell design strength Part 1: Tabulation method for steel valve shells EN 12516-2, Industrial valves Shell design strength

32、Part 2: Calculation method for steel valve shells EN 12516-3, Industrial valves Shell design strength Part 3: Experimental method EN 12570, Industrial valves Method for sizing the operating element EN 12627, Industrial valves Butt welding ends for steel valves EN 12760, Valves Socket welding ends fo

33、r steel valves EN 12982, Industrial valves End-to-end and centre-to-end dimensions for butt welding end valves EN ISO 228-1:2003, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) EN ISO 5210, Industrial valves Multi-

34、turn valve actuator attachments (ISO 5210:1991) EN ISO 15607, Specification and qualification of welding procedures for metallic materials General rules (ISO 15607:2003) ISO 7-1:1994, Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation ASME

35、 B1.20.1-1983, Pipe Threads, General Purpose (Inch) 3 Terms and definitions For the purposes of this document, the definitions of types of valves and components and the terms and definitions given in EN 736-1:1995, EN 736-2:1997 and EN 736-3:2008 apply. NOTE The terms maximum allowable pressure, PS,

36、 and test pressure, PT, defined in EU Directive 97/23/EC (PED) are equivalent to the terms allowable pressure, ps, and test pressure, pt, defined in EN 736-3:2008. DIN EN 13709:2010-10 EN 13709:2010 (E) 6 4 Requirements 4.1 Design 4.1.1 Materials 4.1.1.1 The body and bonnet materials shall be select

37、ed from the grades listed in EN 12516-1. 4.1.1.2 All the internal parts in contact with the fluid shall be made of a material whose corrosion resistance to the fluid being carried is at least equal to the body and bonnet material. 4.1.1.3 Trim materials shall have a chemical composition and mechanic

38、al properties, which ensure the mechanical integrity of the valve. The trim comprises the following: a) stem; b) obturator seat; c) body seat; d) backseat (for valves DN 50 and above, when fitted). 4.1.1.4 Stems shall be manufactured from forged, drawn or rolled material. They shall have a minimum c

39、orrosion resistance equivalent to a 13 % chromium content ferritic steel. 4.1.2 Pressure/temperature ratings 4.1.2.1 The pressure/temperature ratings shall be as specified in EN 12516-1 for the particular body/bonnet material group. 4.1.2.2 The pressure temperature ratings applicable to Class 800 so

40、cket welding and threaded end valves shall be the Class 600 rating for the applicable material group multiplied by the ratio of 800 : 600. 4.1.2.3 Restrictions of temperature and pressure below those specified in 4.1.2.1 and 4.1.2.2 for example, those imposed by soft seals, special trims and bellows

41、 seal shall be indicated on the valve (see 8.1.2). 4.1.2.4 For temperatures below the lowest temperature shown in the pressure/temperature rating tables in EN 12516-1 the maximum allowable pressure shall be no greater than the pressure corresponding to the lowest temperature in the rating tables. Th

42、e use of valves at lower temperatures than shown in the rating tables is permitted providing the bending rupture energy of the body and bonnet material measured on three 10 mm x 10 mm specimens, in accordance with EN 10045-1, shall be no less than an average of 27 J at a temperature no higher than t

43、he lowest scheduled operating temperature. 4.1.3 Dimensions 4.1.3.1 Face-to-face, centre-to-face, end-to-end and centre-to-end dimensions Face-to-face and centre-to-face dimensions for PN and Class designated flanged end valves shall be in accordance with EN 558. The end-to-end and centre-to-end dim

44、ensions of butt welding end valves shall be in accordance with EN 12982. The end-to-end and centre-to-end dimensions of socket welding and threaded end valves are at the choice of the manufacturer. DIN EN 13709:2010-10 EN 13709:2010 (E) 7 4.1.3.2 Body end 4.1.3.2.1 Flanged ends shall comply with the

45、 requirements of EN 1092-1 for PN designated flanges or EN 1759-1 for Class designated flanges. Flanged ends shall be cast or forged integral with the body except that flanges may be attached by welding in accordance with 4.1.7. A full penetration butt weld shall be used for the attachment of flange

46、s by welding on sizes larger than DN 50. 4.1.3.2.2 Butt welding end profiles shall be in accordance with EN 12627. 4.1.3.2.3 Socket welding end dimensions shall be in accordance with EN 12760. The minimum thickness of the pressure retaining material shall be in accordance with EN 12516-1 or EN 12516

47、-2. 4.1.3.2.4 Threaded ends shall be of the internal form in accordance with Type Rc and Rp to ISO 7-1:1994 or Type G to EN ISO 228-1:2003 or Type NPT to ASME B1.20.1-1983. 4.1.3.3 Body end port inside diameter The body end port shall be circular. For unlined valves, the body end port inside diamete

48、r shall be not less than the nominal inside diameter specified in Table 1. Table 1 Nominal inside diameter of the body end port Dimensions in millimetres DN PN 10 PN 16 Class 150 PN 25 PN 40 Class 300 PN 63 PN 100 Class 600 Class 800 8 8 8 6 8 8 6 8 6 6 6 10 10 10 9 10 10 9 10 9 9 9 12 12 12 12 12 12 12 12 11 11 11 15 15 15 13 13 13 13 13 13 13 12 20 20 20 19