DIN EN 13677-3-2003 Reinforced thermoplastic moulding compounds - Specification for GMT - Part 3 Specific requirements German version EN 13677-3 2003《增强的热塑性模塑复合材料 GMT规范 第3部分 特殊要求》.pdf

《DIN EN 13677-3-2003 Reinforced thermoplastic moulding compounds - Specification for GMT - Part 3 Specific requirements German version EN 13677-3 2003《增强的热塑性模塑复合材料 GMT规范 第3部分 特殊要求》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13677-3-2003 Reinforced thermoplastic moulding compounds - Specification for GMT - Part 3 Specific requirements German version EN 13677-3 2003《增强的热塑性模塑复合材料 GMT规范 第3部分 特殊要求》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、ICS 83.120Verstrkte Thermoplast-Formmassen Spezifikation fr GMT Teil 3: Besondere AnforderungenEuropean Standard EN 13677-3 : 2003 has the status of a DIN Standard.A comma is used as the decimal marker.National forewordThis standard has been prepared by CEN/TC 249 Plastics (Secretariat: Belgium).The

2、 responsible German body involved in its preparation was the Normenausschuss Kunststoffe (PlasticsStandards Committee), Technical Committee Rieselfhige Duroplaste und langfaserverstrkte Kunststoffe.DIN 53479 and DIN 53464 are the standards corresponding to International Standards ISO 1183 andISO 257

3、7, respectively, referred to in clause 2 of the EN.National Annex NAStandards referred to(and not included in Normative references and Bibliography)DIN 53464 Determination of shrinkage properties of mouldings from thermosetting moulding materialsDIN 53479 Determination of density of plastics and ela

4、stomersRef. No. DIN EN 13677-3 : 2003-07English price group 06 Sales No. 110611.03DEUTSCHE NORM July 2003EN 13677-3EN comprises 6 pages. No part of this standard may be reproduced without the prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany

5、,has the exclusive right of sale for German Standards (DIN-Normen).Reinforced thermoplastic moulding compounds Specification for GMTPart 3: Specific requirementsEnglish version of DIN EN 13677-3February 2003English versionICS 83.120Management Centre: rue de Stassart 36, B-1050 BrusselsEuropean Commi

6、ttee for StandardizationComit Europen de NormalisationEuropisches Komitee fr NormungReinforced thermoplastic moulding compounds Specification for GMTPart 3: Specific requirements 2003. CEN All rights of exploitation in any form and by any meansreserved worldwide for CEN national members.Ref. No. EN

7、13677-3 : 2003 EPrimprgns renforcs thermoplasti-ques Spcifications des GMT Partie 3: Exigences particuliresVerstrkte Thermoplast-Formmas-sen Spezifikation fr GMT Teil 3:Besondere AnforderungenThis European Standard was approved by CEN on 2002-11-28.CEN members are bound to comply with the CEN/CENELE

8、C Internal Regulationswhich stipulate the conditions for giving this European Standard the status of anational standard without any alteration.Up-to-date lists and bibliographical references concerning such national stand-ards may be obtained on application to the Management Centre or to any CENmemb

9、er.The European Standards exist in three official versions (English, French, German).A version in any other language made by translation under the responsibility of aCEN member into its own language and notified to the Management Centre hasthe same status as the official versions.CEN members are the

10、 national standards bodies of Austria, Belgium, the CzechRepublic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland,Ireland, Italy, Luxembourg, Malta, the Netherlands, Norway, Portugal, Slovakia,Spain, Sweden, Switzerland, and the United Kingdom.EN 13677-3Page 2EN 13677-3 : 200323334456Page 3EN 13677-3 : 2003Page 4EN 13677-3 : 2003Page 5EN 13677-3 : 2003Page 6EN 13677-3 : 2003