DIN EN 13567-2007 Protective clothing - nHand arm chest abdomen leg genital and face protectors for fencers - nRequirements and test methods (includes Amendment A1 2007) English ve.pdf

《DIN EN 13567-2007 Protective clothing - nHand arm chest abdomen leg genital and face protectors for fencers - nRequirements and test methods (includes Amendment A1 2007) English ve.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13567-2007 Protective clothing - nHand arm chest abdomen leg genital and face protectors for fencers - nRequirements and test methods (includes Amendment A1 2007) English ve.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、September 2007DEUTSCHE NORM English price group 16No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 13.340.10!$H|y“13789

2、86www.din.deDDIN EN 13567Protective clothing Hand, arm, chest, abdomen, leg, genital and face protectors forfencers Requirements and test methods (includes Amendment A1:2007)English version of DIN EN 13567:2007-09Schutzkleidung Hand-, Arm-, Brustkorb-, Unterleibs-, Bein-, Genital- und Gesichtsschtze

3、r fr Fechter Anforderungen und Prfverfahren (enthlt nderung A1:2007)Englische Fassung DIN EN 13567:2007-09SupersedesDIN EN 13567:2002-10www.beuth.deDocument comprises 46 pages 11.07DIN EN 13567:2007-09 2 Start of validity This standard is valid from 1 September 2007. National foreword This standard

4、has been prepared by Technical Committee CEN/TC 162 “Protective clothing including hand and arm protection and lifejackets”, the Secretariat of which is held by DIN (Germany). The responsible German body involved in its preparation was the Normenausschuss Sport- und Freizeitgert (Sports Equipment St

5、andards Committee), Technical Committee NA 112-04-03 AA Krperschutz. The DIN Standards corresponding to the International Standards referred to in clause 2 of the EN are as follows: ISO 3758 DIN EN ISO 3758 ISO 6330 DIN EN ISO 6330 ISO 7500-1 DIN EN ISO 7500-1 Amendments This standard differs from D

6、IN EN 13567:2002-10 as follows: a) Fencing masks shall now be sized against the users vertical head circumference. b) In clause 3, the term “vertical circumference of the head” has been added. c) The requirements for testing the zones of protection of socks have been dropped. d) The requirements for

7、 the examination of zones of protection, for restraint testing of masks, for bib attachment testing, penetration testing and burst testing have been modified. Previous editions DIN EN 13567: 2002-10 National Annex NA (informative) Bibliography DIN EN ISO 3758, Textiles Care labelling code using symb

8、ols DIN EN ISO 6330, Textiles Domestic washing and drying procedures for textile testing DIN EN ISO 7500-1, Metallic materials Verification of static uniaxial testing machines Part 1: Tension/ compression testing machines Verification and calibration of the force-measuring system EUROPEAN STANDARD N

9、ORME EUROPENNE EUROPISCHE NORM EN 13567:2002+A1 June 2007 ICS 13.340.10 Supersedes EN 13567:2002English Version Protective clothing - Hand, arm, chest, abdomen, leg, genital and face protectors for fencers - Requirements and test methods Vtements de protection - Protection des mains, des bras, face

10、pour les escrimeurs - Exigences et mthodes dessaiSchutzkleidung - Hand-, Arm-, Brustkorb-, Unterleibs-, Bein-, Genital- und Gesichtsschtzer fr Fechter - Anforderungen und Prfverfahren This European Standard was approved by CEN on 25 March 2002 and includes Amendment 1 approved by CEN on 10 May 2007.

11、 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on

12、application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Cen

13、tre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pola

14、nd, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by

15、 any means reserved worldwide for CEN national Members. Ref. No. EN 13567:2002+A1:2007: Ede la p trine, de labdomen, des jambes, gnitales et de la ioEN 13567:2002+A1:2007 (E) Contents page Foreword3 Introduction .4 1 Scope 4 2 Normative references 4 3 Terms and definitions .5 4 Requirements.9 4.1 Ge

16、neral9 4.2 Innocuousness.9 4.3 Ergonomic requirements 9 4.4 Restraint requirements .9 4.5 Sizing 9 4.6 Minimum dimensions of zones of protection .10 4.7 Construction materials and construction details.18 4.8 Penetration resistance 20 4.9 Burst strength of seams .22 5 Test methods22 5.1 Instruments 2

17、2 5.2 Products for testing.22 5.3 Conditioning of products23 5.4 Innocuousness.23 5.5 Ergonomic testing .23 5.6 Sizing 24 5.7 Examination of zones of protection.24 5.8 Restraint testing of masks24 5.9 Bib attachment testing 25 5.10 Penetration testing 26 5.11 Burst testing.35 6 Marking .36 7 Informa

18、tion to be supplied by the manufacturer36 Annex A (informative) Information about determining the chemical innocuousness of protective clothing and equipment 38 A.1 General38 A.2 Evidence of innocuousness .38 A.3 Possible specific innocuousness testing .38 Annex B (informative) Levels of protection.

19、40 B.1 Performance levels40 B.2 Performance of combinations40 B.3 Fencing jackets, breeches and underpants40 B.4 Masks - bibs .41 Annex C (informative) Visors and masks made of material other than steel wire mesh 42 Annex ZA (informative) Clauses of this European Standard addressing essential requir

20、ements or other provisions of EU Directives43 Bibliography44 2 EN 13567:2002+A1:2007 (E) Foreword This document (EN 13567:2002+A1:2007) has been prepared by Technical Committee CEN/TC 162 “Protective clothing including hand and arm protection and lifejackets“, the secretariat of which is held by DIN

21、. This document shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2007 and conflicting national standards shall be withdrawn at the latest by December 2007. This document includes Amendment 1, approved by CEN on

22、2007-05-10. This document supersedes EN 13567:2002. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports esse

23、ntial requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European

24、Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

25、 3 EN 13567:2002+A1:2007 (E) Introduction Fencing by virtue of being a combat sport in which body contact by the weapon occasionally (but usually inadvertently) occurs outside the zones of protection, is by its nature dangerous. Protective clothing and equipment for fencers is intended as far as pos

26、sible to prevent injuries, or in the worst cases to reduce the severity of injuries, particularly by the point of the weapon. Broken blades pose a particular threat. The circumstances of the breakage of blades may result in high tip velocities and consequent high energy impacts by the broken blade.

27、Broken blades have been known to penetrate protective equipment with fatal consequences. No practical clothing is capable of withstanding all broken blade impacts. In this standard the concept of the optimum level of protection has been taken into account. This concept is that the level of protectio

28、n specified should be as high as it can be, without causing such unacceptable discomfort or impediment to fencing movements that fencers would not use the protective clothing. The clothing specified in this standard provides two levels of protection perceived by the organisers and participants in th

29、e sport to be appropriate. Its use is expected to reduce risks of injuries to fencers to a tolerable level. 1 Scope This European Standard specifies the general requirements for ergonomics, sizing, coverage and performance of protective clothing and equipment for use in the sport of fencing. Require

30、ments for the marking of clothing and equipment and the information to be supplied by the manufacturer are given. Test methods are described and performance levels are defined. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publication

31、s. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. Fo

32、r undated references the latest edition of the publication referred to applies (including amendments). EN 166:2001, Personal eye-protection Specifications. EN 388, Protective gloves against mechanical risks. EN 420, General requirements for gloves. EN 1082-1:1996, Protective clothing Gloves and arm

33、guards protecting against cuts and stabs by hand knives Part 1: Chain mail gloves and arm guards. EN ISO 5084:1996, Textiles Determination of thickness of textiles and textile products (ISO 5084:1996). EN 13546:2002, Protective clothing Hand, arm, chest, abdomen, leg, foot and genital protectors for

34、 field hockey goal keepers, and shin protectors for field players Requirements and test methods. EN 13595-3:2002, Protective clothing for professional motorcycle riders Jackets, trousers and one-piece or divided suits Part 3: Test method for determination of burst strength. EN ISO 13938-1:1999, Text

35、iles Bursting properties of fabrics Part 1: Hydraulic method for determination of bursting strength and bursting distension (ISO 13938-1:1999). 4 EN 13567:2002+A1:2007 (E) EN ISO 13938-2:1999, Textiles Bursting properties of fabrics Part 2: Pneumatic method for determination of bursting strength and

36、 bursting distension (ISO 13938-2:1999). !deleted text“ ISO 3758, Care labelling code using symbols. ISO 6330:2000, Textiles Domestic washing and drying procedures for textile testing. ISO 7500-1:1999, Metallic materials Verification of static uniaxial testing machines Part 1: Torsion/compression te

37、sting machines Verification and calibration of the force-measuring system. ISO 8559:1989, Garment construction and anthropometric surveys Body dimensions. 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 protective clothing and equipm

38、ent clothing and specific devices worn on the body, arms, hands and legs and over the face and neck, that are intended to reduce the severity of injuries from fencing weapons 3.2 zone of protection area of protective equipment that is intended to provide protection, and is subject to specific testin

39、g 3.3 coverage area of the fencers body covered by the whole item of protective clothing or equipment and its attachments 3.4 garment unit of clothing which itself has an integral zone of protection replacing or in addition to an article of non-protective clothing 3.5 handedness designs and the mark

40、ings on equipment that relate to its intended use by fencers holding their weapons in the right hands or left hands or whether the equipment is for ambidextrous use by right or left handed fencers 3.6 performance level number designating the level of the protection that it is intended the product sh

41、ould provide. This number is used in designating the test severity to which the product is to be subjected. For non-normative guidance on performance levels and the choice of equipment see annex B 3.7 fencing International and Olympic sport based on European duelling with swords and embracing discip

42、lines characterised by the relevant weapons 3.8 weapon collective term covering the following specific swords used in fencing 5 EN 13567:2002+A1:2007 (E) 3.8.1 foil rectangular section blade conventional duelling weapon with which hits are scored with the point only. The target is the anterior of th

43、e torso including the abdomen and the posterior torso down to the waist. The head, arms and legs are excluded, but are often hit 3.8.2 epee traditional duelling weapon of V section blade with which hits are scored only with the point, and for which the target is the whole body, including the head an

44、d feet 3.8.3 sabre weapon derived from the Cavalry sabre with a blunt cutting edge. Hits are scored with any part of the blade. The target is the whole body above the waist with the exception of the hands 3.9 point expanded and/or flattened end of the blade of a weapon so designed as to reduce the p

45、ossibility of the perforation of the protective clothing 3.10 fencing mask protective device covering the face and sides of the head and the front of the neck. The parts are illustrated in Key ! a) Front view b) Side view “ 1 Hard shell 2 Lateral protection 3 Bib 4 Visor (optional) Figure 1 Componen

46、t parts of a fencing mask 6 EN 13567:2002+A1:2007 (E) 3.10.1 hard shell framework, part of which is see-through covering the face of the head 3.10.2 lateral protection framework, part of which can be see-through covering the sides of the head and meeting over the top of the head 3.10.3 mask bib prot

47、ective element covering the front of the neck 3.10.4 visor optional transparent area of the mask replacing part or all of the hard shell 3.10.5 join any junction between the hard shell and visor, or hard shell or visor and the lateral protection 3.10.6 see-through area region of the hard shell throu

48、gh which a fencer is able to see their opponent 3.11 fencing clothing clothing designed specifically for the sport of fencing 3.11.1 fencing jacket garment covering the full length of both arms from the wrist to the shoulder, the chest and at least the upper part of the abdomen 3.11.2 fencing breech

49、es (trousers) garment covering the abdomen, thighs and knees (and occasionally the lower leg) 3.11.3 fencing underpants protective garment covering the abdomen and upper half of the thigh. If used, this garment is worn inside the trousers 3.11.4 (fencing) under plastron one armed garment worn under a jacket covering at least part of the weapon arm, the axilla (armpit) of the weapon arm and part of the chest wall on the same side NOTE There are two-armed under plastrons which cover both of the fencers arms. Th