DIN EN 13553-2015 Resilient floor coverings - Polyvinyl chloride floor coverings for use in special wet areas - Specification German version EN 13553 2015《弹性地板覆盖物 用于特别潮湿地区的聚氯乙烯地板覆盖.pdf

《DIN EN 13553-2015 Resilient floor coverings - Polyvinyl chloride floor coverings for use in special wet areas - Specification German version EN 13553 2015《弹性地板覆盖物 用于特别潮湿地区的聚氯乙烯地板覆盖.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13553-2015 Resilient floor coverings - Polyvinyl chloride floor coverings for use in special wet areas - Specification German version EN 13553 2015《弹性地板覆盖物 用于特别潮湿地区的聚氯乙烯地板覆盖.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、June 2015 Translation by DIN-Sprachendienst.English price group 10No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 9

2、7.150!%Bo“2319876www.din.deDDIN EN 13553Resilient floor coverings Polyvinyl chloride floor coverings for use in special wet areas Specification;English version EN 13553:2015,English translation of DIN EN 13553:2015-06Elastische Bodenbelge Polyvinylchlorid-Bodenbelge zur Anwendung in besonderen Nassr

3、umen Spezifikation;Englische Fassung EN 13553:2015,Englische bersetzung von DIN EN 13553:2015-06Revtements de sol rsilients Revtements de sol base de polychlorure de vinyle pour zones humides spciales Spcification;Version anglaise EN 13553:2015,Traduction anglaise de DIN EN 13553:2015-06SupersedesDI

4、N EN 13553:2002-07www.beuth.deDocument comprises 1 pagesIn case of doubt, the German-language original shall be considered authoritative.404.15DIN EN 13553:2015-06 2 A comma is used as the decimal marker. National foreword This document (EN 13553:2015) has been prepared by Technical Committee CEN/TC

5、 134 “Resilient, textile and laminate floor coverings” (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was the DIN-Normenausschuss Kunststoffe (DIN Standards Committee Plastics), Working Committee NA 054-04-05 AA Elastische Bodenbelge. Amendments This standard di

6、ffers from DIN EN 13553:2002-07 as follows: a) normative references have been updated. Previous editions DIN EN 13553: 2002-07 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13553 April 2015 ICS 97.150 Supersedes EN 13553:2002English Version Resilient floor coverings - Polyvinyl chloride floor

7、 coverings for use in special wet areas - Specification Revtements de sol rsilients - Revtements de sol base de polychlorure de vinyle pour zones humides spciales - Spcification Elastische Bodenbelge - Polyvinylchlorid-Bodenbelge zur Anwendung in besonderen Nassrumen - Spezifikation This European St

8、andard was approved by CEN on 1 February 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerni

9、ng such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into i

10、ts own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germ

11、any, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR

12、 NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13553:2015 EEN 13553:2015 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and

13、definitions .4 4 Requirements .4 4.1 General requirements 4 4.2 Additional performance requirements 5 4.3 Installation 5 5 Marking .5 Annex A (normative) Water tightness test .6 A.1 Scope 6 A.2 Apparatus .6 A.3 Test specimen 6 A.4 Conditioning .7 A.5 Testing 7 A.6 Test report 8 Annex B (informative)

14、 Choice of floor covering category 9 Annex C (informative) Installation . 10 Annex D (informative) Determination of elongation at break (optional property) 11 D.1 Apparatus, sampling and preparation of test pieces 11 D.2 Procedure 11 D.3 Calculation and expression of result 11 D.4 Requirement 11 D.5

15、 Test report . 11 DIN EN 13553:2015-06 EN 13553:2015 (E) 3 Foreword This document (EN 13553:2015) has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN. This European Standard shall be given the status of a nati

16、onal standard, either by publication of an identical text or by endorsement, at the latest by October 2015 and conflicting national standards shall be withdrawn at the latest by October 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of paten

17、t rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13553:2002. Significant changes compared to the previous edition are: Superseded EN standards were replaced by corresponding EN ISO standards. According to the CEN-CE

18、NELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary,

19、Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 13553:2015-06 EN 13553:2015 (E) 4 1 Scope This European standard specifies the minimum additional chara

20、cteristics which are necessary for: polyvinyl chloride floor coverings in roll form according to EN ISO 10581 or EN ISO 10582 and polyvinyl chloride floor coverings with foam backing in roll form to EN 651 to be installed satisfactorily in special wet areas to form a watertight installation with a l

21、ong life. It specifies two categories (A and B) for use on different substrates. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undat

22、ed references, the latest edition of the referenced document (including any amendments) applies. EN 651, Resilient floor coverings - Polyvinyl chloride floor coverings with foam layer - Specification EN 661, Resilient floor coverings - Determination of the spreading of water EN 684, Resilient floor

23、coverings - Determination of seam strength EN 12466, Resilient floor coverings - Vocabulary EN ISO 10581, Resilient floor coverings - Homogeneous poly(vinyl chloride) floor covering - Specifications (ISO 10581) EN ISO 10582, Resilient floor coverings - Heterogeneous poly(vinyl chloride) floor coveri

24、ngs - Specification (ISO 10582) EN ISO 24340, Resilient floor coverings - Determination of thickness of layers (ISO 24340) EN ISO 24344, Resilient floor coverings - Determination of flexibility and deflection (ISO 24344) EN ISO 24346, Resilient floor coverings - Determination of overall thickness (I

25、SO 24346) 3 Terms and definitions For the purposes of this document the terms and definitions of EN 12466 and the following term and definition apply: 3.1 special wet area area where floors are designed to be frequently or permanently wet and equipped with a floor-based drain EXAMPLE Bathrooms with

26、free-standing tubs and shower rooms without partitions. 4 Requirements 4.1 General requirements Products covered by this standard shall conform to the requirements of EN ISO 10581, EN ISO 10582 or EN 651. DIN EN 13553:2015-06 EN 13553:2015 (E) 5 4.2 Additional performance requirements Floor covering

27、s conforming to the requirements of EN ISO 10581, EN ISO 10582 or EN 651 are suitable for special wet areas when they meet the additional requirements specified in Table 1. Table 1 Products suitable for special wet areas Characteristic Identity code W1 Identity code W2 Identity code W3 Test method F

28、loor covering type a)Floor coverings conforming to EN ISO 10581 or EN ISO 10582 Floor coverings conforming to EN ISO 10581 or EN ISO 10582 Floor coverings conforming to EN 651 Substrate type b)Category A Category B Category A Nominal overall thickness (in mm) 1,5 2,0 EN ISO 24346 Total thickness of

29、compact layers (in mm) as for overall thickness as for overall thickness 1,0 EN ISO 24340 Spreading of water (in days) - - 7 EN 661 Seam strength, when welded in accordance with the manufacturersinstructions (in N/50 mm) 240 400 240 EN 684 Flexibility When bent around a mandrel of 10 mm diameter, no

30、 cracking or other surface deterioration shall be visible with the naked eye For heterogeneous materials the test shall be made with the surface side as well as with the reverse side outwards. EN ISO 24344 Water tightness The welded product shall be classified watertight. Annex A a)For installation

31、see Annex C b)For choice of category see Annex B 4.3 Installation See Annex C. 5 Marking Floor coverings covered by this standard and/or their packaging shall bear the following marking in addition to the marking according to EN ISO 10581, EN ISO 10582 or EN 651; a) number and year of publication of

32、 this European Standard (EN 13553:2015); b) identity code W1, W2 or W3; c) category A or B. DIN EN 13553:2015-06 EN 13553:2015 (E) 6 Annex A (normative) Water tightness test A.1 Scope This annex describes a method for testing the water tightness of floor coverings. A.2 Apparatus A.2.1 A base of non-

33、porous material such as metal or glass, on which the sample rests during testing. NOTE If the base is transparent and suitably supported, it will enable any leakage to be observed from below. A.2.2 A watertight, bottomless box-frame, to be placed on top of the test specimen. The box-frame shall have

34、 vertical sides at least 300 mm and shall cover a surface area of at least 300 mm x 500 mm. The box-frame will be supporting water pressure and should therefore be held in place by clamps or weights. The box-frame shall be sealed to achieve water tightness between the floor covering and the box-fram

35、e. A.2.3 Indicator paper, sensitive to moisture. A.3 Test specimen The test specimen shall be flat or capable of being flattened so that it lies flat on the base. The base may be covered by polyethylene foil or similar material. When preparing test specimens the manufacturers instructions shall be o

36、bserved. The size of the specimen shall be at least 500 mm x 800 mm and it shall be provided with seams welded in accordance with manufacturers recommendations (see Figure A.1). DIN EN 13553:2015-06 EN 13553:2015 (E) 7 Dimensions in mm Key 1 welded seam Figure A.1 Specimen with welded seams A.4 Cond

37、itioning Special conditioning is not required. The test specimen shall be dry on visual inspection and be at a temperature of 15 C to 25 C. A.5 Testing The temperature of the water during testing shall be 15 C to 25 C. Cover the supporting base with the indicator paper. Place the test specimen on th

38、e indicator paper with the use surface upwards. Place the box-frame over the test specimen and press the support towards the box-frame to ensure water tightness (see A.2 and Figure A.2). Fill the box-frame with water to a level of 200 mm 10 mm above the upper surface of the test specimen. This water

39、 level is maintained for 24 h 1 h after which the water is drained off. The moisture indicator and the test specimen are examined for any signs of water penetrating the specimen. The test specimen is considered watertight if there is no sign of penetrating water. DIN EN 13553:2015-06 EN 13553:2015 (

40、E) 8 Dimensions in mm Key 1 position of box-frame on specimen Figure A.2 Position of box-frame on specimen A.6 Test report The test report shall contain the following information: a) reference to this method i.e. EN 13553, Annex A; b) the material tested (type, source, colour and manufacturers refer

41、ence numbers); c) preparation of the sample for testing; d) result of inspection according to A.5. DIN EN 13553:2015-06 EN 13553:2015 (E) 9 Annex B (informative) Choice of floor covering category The choice of category should be made according to national codes of practice. If a code of practice doe

42、s not exist the criteria of choice should be the following: Category A: For use on all substrates where traffic intensity or risk of mechanical damage is normal. Category B: For use on all substrates where traffic intensity or risk of mechanical damage is higher than normal. DIN EN 13553:2015-06 EN

43、13553:2015 (E) 10 Annex C (informative) Installation Products according to this standard should be installed according to manufacturers instructions for wet area installation for the product, and any national codes of practice. The installations should be carried out by an installer skilled in wet a

44、rea installations and in a manner that ensures a correct installation DIN EN 13553:2015-06 EN 13553:2015 (E) 11 Annex D (informative) Determination of elongation at break (optional property) D.1 Apparatus, sampling and preparation of test pieces As specified in EN 684 D.2 Procedure The procedure des

45、cribed in EN 684 shall be used. Additionally the length of the test specimen at break shall be measured. D.3 Calculation and expression of result Calculate the elongation at break for each test specimen as follows: 100( ) 100LLL= (D.1) where is the elongation at break in %; L0is the initial test len

46、gth between jaws, i.e. (100 0,5) mm; L1is the test length at break. Calculate the mean value of the five tests and express the result to the nearest 1% of the distance between jaws. Also record the minimum of the individual values. D.4 Requirement Elongation at break shall be 15% for each specimen.

47、DIN EN 13553:2015-06 EN 13553:2015 (E) 12 h) any deviation from this standard which may have affected the results. DIN EN 13553:2015-06 D.5 Test report The test report shall contain the following information: a) reference to this test method, EN 13553 Annex D; b) complete identification of the produ

48、ct tested, including type, source, colour and manufacturers reference numbers; c) previous history of the sample; d) description of the welding process; e) mean value of the elongation at break; f) minimum value of the elongation at break; g) type of failure if not in the seam, e.g. failure due to breaking of test specimen;