DIN EN 13476-1-2007 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U) polypr.pdf

《DIN EN 13476-1-2007 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U) polypr.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13476-1-2007 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U) polypr.pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、August 2007DEUTSCHE NORM English price group 14No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 93.030!,zjI“9877138www.

2、din.deDDIN EN 13476-1Plastics piping systems for non-pressure underground drainage andsewerage Structured-wall piping systems of unplasticized poly(vinyl chloride)(PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: General requirements and performance characteristicsEnglish version of DIN EN 1

3、3476-1:2007-08Kunststoff-Rohrleitungssysteme fr erdverlegte drucklose Abwasserkanle und-leitungen Rohrleitungssysteme mit profilierter Wandung aus weichmacherfreiem Polyvinylchlorid(PVC-U), Polypropylen (PP) und Polyethylen (PE) Teil 1: Allgemeine Anforderungen und LeistungsmerkmaleEnglische Fassung

4、 DIN EN 13476-1:2007-08www.beuth.deDocument comprises 31 pages10.07DIN EN 13476-1:2007-08 2 National foreword This standard has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” (Secretariat: NEN, the Netherlands). The responsible German bodies involved in

5、 its preparation were the Normenausschuss Wasserwesen (Water Practice Standards Committee) and the Normenausschuss Kunststoffe (Plastics Standards Committee), Joint Committee NA 119-05-28 GA (GA NAW/FNK) Kunststoffrohre in der Abwassertechnik. According to Annex B (informative) “Structural design ba

6、sed on a design calculation” the method described in DIN EN 1295-1 should be used when designing underground systems subject to loading conditions other than those given in Table B.1. In Germany, the method specified in ATV DWK A 127 (Code of practice for structural analysis of drains and sewers) is

7、 usually used in such conditions. EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13476-1May 2007ICS 93.030English VersionPlastics piping systems for non-pressure underground drainageand sewerage - Structured-wall piping systems of unplasticizedpoly(vinyl chloride) (PVC-U), polypropylene (PP) andp

8、olyethylene (PE) - Part 1: General requirements andperformance characteristicsSystmes de canalisations en plastique pour lesbranchements et les collecteurs dassainissements sanspression enterrs - Systmes de canalisation paroisstructures en poly(chlorure de vinyle) non plastifi (PVC-U), polypropylne

9、(PP) et polythylne (PE) - Partie 1:Exigences gnrales et caractristiques de performanceKunststoff-Rohrleitungssysteme fr erdverlegte druckloseAbwasserkanle und -leitungen - Rohrleitungssysteme mitprofilierter Wandung aus weichmacherfreiemPolyvinylchlorid (PVC-U), Polypropylen (PP) undPolyethylen (PE)

10、 - Teil 1: Allgemeine Anforderungen undLeistungsmerkmaleThis European Standard was approved by CEN on 5 March 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any a

11、lteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by tr

12、anslationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany

13、, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagem

14、ent Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13476-1:2007: EEN 13476-1:2007 (E) 2 Contents Page Foreword 4 Introduction 5 1 Scope 6 2 Normative references 6 3 Terms and definiti

15、ons, symbols and abbreviations 7 3.1 Definitions 7 3.1.1 General definitions 7 3.1.2 Geometrical definitions 8 3.2 Symbols and abbreviations 9 4 Material 10 4.1 General 10 4.2 Utilisation of non-virgin material 10 4.3 Sealing ring retaining components 10 4.4 Sealing rings 10 4.5 Fused or welded join

16、ts 10 5 Designation of wall construction 10 6 Appearance and colour 10 6.1 Appearance 10 6.2 Colour 11 7 Geometrical characteristics 11 8 Types of fittings 11 8.1 General 11 8.2 Design length of fittings 14 9 System performance related test methods and characteristics 14 10 Marking, general 16 10.1

17、Presentation 16 10.2 Marking process 16 10.3 Size 16 Annex A (informative) Characteristics of PVC-U, PP and PE pipes and fittings 17 A.1 General 17 A.2 Material characteristics 17 A.3 Chemical resistance 17 A.4 Abrasion resistance 18 A.5 Hydraulic roughness 18 Annex B (informative) Structural design

18、 19 B.1 General 19 B.2 Structural design based on practical experience 19 B.3 Structural design based on a design calculations 21 B.4 Selection of fitting stiffness or class 21 Annex C (informative) Designation of pipes and corresponding fittings 23 Annex D (informative) Guidance in cleaning plastic

19、s pipes 24 D.1 Introduction 24 D.2 Cleaning and unblocking 24 EN 13476-1:2007 (E) 3 D.2.1 Choosing the right equipment 24 D.2.2 Comparing techniques 24 D.3 Conclusions from independent jetting tests 25 D.3.1 Assessing efficiency and impact 25 D.3.2 Testing of plastic pipes 25 D.3.3 Clearing tests 25

20、 D.4 Supplementary cleaning techniques 26 D.5 Recommended practice principles for jetting 26 Bibliography 28 EN 13476-1:2007 (E) 4 Foreword This document (EN 13476-1:2007) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is h

21、eld by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2007, and conflicting national standards shall be withdrawn at the latest by November 2007. This standard is a part of a System

22、 Standard for plastics piping systems of particular materials for specified applications. There are a number of such System Standards. System Standards are based on the results of the work being undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, which is a Te

23、chnical Committee of the International Organization for Standardization (ISO). They are supported by separate standards on test methods to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommende

24、d practice for installation. EN 13476 consists of the following Parts under the general title Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE): Part 1: Gen

25、eral requirements and performance characteristics (this standard); Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A; Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B;

26、Part 4: Assessment of conformity (CEN/TS); Part 5: Guidance for installation (CEN/TS).1For pipes and fittings which have conformed to the relevant national standard before May 2007, as shown by the manufacturer or by a certification body, the national standard may continue to be applied until May 20

27、09. National standards specifically for pipes and fittings for the transport of surface water are not considered to be conflicting with this standard and may thus be allowed to coexist. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries

28、 are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, S

29、weden, Switzerland and United Kingdom. 1The feasibility of this project is under study. EN 13476-1:2007 (E) 5 Introduction Due to the variety in materials, pipe constructions, application areas and classes, several combinations are possible. The purchaser or specifier may select between these possib

30、ilities by designating the pipe and fitting he or she prefers to use for each case, as described in Annex C, Designation of pipes and corresponding fittings, taking into account any particular requirements and relevant national regulations and installation practices or codes. EN 13476-1:2007 (E) 6 1

31、 Scope This European Standard, together with EN 13476-2 and EN 13476-3, specifies the definitions and general requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are to be us

32、ed for non-pressure underground drainage and sewerage systems. This standard is applicable to: a) structured-wall pipes and fittings, which are to be used buried in the ground outside a building structure only; reflected by the marking of products by “U”; b) structured-wall pipes and fittings, which

33、 are to be used buried in ground both outside (application area code “U”) and within a building structure (application area code “D”); reflected in the marking of products by “UD”. In conjunction with EN 13476-2 and EN 13476-3 it is applicable to structured-wall pipes and fittings with or without an

34、 integral socket with elastomeric ring seal joints, as well as welded and fused joints. This part specifies general aspects and gives guidance concerning a national selection of requirement levels and classes where part 2 and part 3 of this standard provide options. EN 13476-2 and EN 13476-3 specify

35、 material characteristics, dimensions and tolerances, test methods, test parameters and requirements for pipes with smooth internal and external surfaces, Type A, and pipes with smooth internal and profiled external surfaces, Type B. This standard, together with EN 13476-2 and EN 13476-3, covers a r

36、ange of pipe and fitting sizes, materials, pipe constructions, stiffness classes and tolerance classes and offers recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particu

37、lar requirements and any relevant national regulations and installation practices or codes. NOTE 2 Pipes, fittings and other components conforming to any plastic product standards referred to in clause 2 can be used with pipes and fittings conforming to this standard, when they conform to the requir

38、ements for joint dimensions given in part 2 and part 3 of this standard and to the performance requirements given in Clause 9. NOTE 3 For dimensions larger than DN 1200 OD/ID this document may serve as general guideline regarding appearance, colour, physical and mechanical characteristics as well as

39、 performance requirements. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

40、 EN 681-1, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber EN 681-2, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elastomers EN 681-4, Elasto

41、meric seals Materials requirements for pipe joint seals used in water and drainage applications Part 4: Cast polyurethane sealing elements EN 13476-2:2007, Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride

42、) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A EN 13476-1:2007 (E) 7 EN 13476-3:2007, Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall pip

43、ing systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B EN ISO 472:2001, Plastics Vocabulary (ISO 472:1999) EN ISO 1043-1:2001, Plasti

44、cs - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics (ISO 1043-1:2001) EN ISO 9969, Thermoplastics pipes Determination of ring stiffness (ISO 9969:1994) ISO 11922-1:1997, Thermoplastics pipes for the conveyance of fluids Dimensions and tolerances Part 1: Metr

45、ic series ISO 13967, Thermoplastics fittings Determination of ring stiffness 3 Terms and definitions, symbols and abbreviations For the purposes of this standard, the terms and definitions given in EN ISO 472:2001, EN ISO 1043-1:2001, ISO 11922-1:1997 and the following apply. 3.1 Definitions 3.1.1 G

46、eneral definitions 3.1.1.1 application area code code used to mark pipes and fittings to indicate the permitted application area(s) for which they are intended, as follows: U: code for the area more than 1 m from the building to which the buried piping system is connected; D: code for the area under

47、 and within 1 m from the building where the pipes and fittings are buried underground and are connected to the soil and waste discharge system of the building NOTE In the “D” application area, the existence of hot water discharge in addition to external forces from the surroundings is usual. 3.1.1.2

48、 structured-wall pipes and fittings products which have an optimised design with regard to material usage to achieve the physical, mechanical and performance requirements of this standard NOTE For a description of the particular designs covered by this standard, see clause 5 in EN 13476-2:2007 and E

49、N 13476-3:2007. 3.1.1.3 fabricated fitting fitting manufactured by heat forming and/or joining more than one piece of pipe and/or moulded component NOTE Sealed ring retaining components are not considered as a piece. EN 13476-1:2007 (E) 8 3.1.2 Geometrical definitions 3.1.2.1 nominal size, DN numerical designation of the size of a component, other than a component designated by thread size, which is approximately equal to the manufacturing dimension in mm 3.1.2.2 nominal size, DN/OD nominal size, related to the outside diamete