DIN EN 1334-1996 Domestic furniture - Beds and mattresses - Methods of measurement and recommended tolerances German version EN 1334 1996《居室家具 床和床垫 测量方法和公差建议》.pdf

《DIN EN 1334-1996 Domestic furniture - Beds and mattresses - Methods of measurement and recommended tolerances German version EN 1334 1996《居室家具 床和床垫 测量方法和公差建议》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1334-1996 Domestic furniture - Beds and mattresses - Methods of measurement and recommended tolerances German version EN 1334 1996《居室家具 床和床垫 测量方法和公差建议》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、DEUTSCHE NORM Julv 1996 Beds and mattresses English version of DIN EN 1334 Methods of measurement and recommeded tolerances c o m .- - L s o U a F z L p - c 3 o) o) - o c o P B - o c o Y) Y) .- .- E Q o Q al L .- 6 o 5 3 +. 3 .- u o o 3 U 2 t m n z ? U c m c Y) c r .- c m o o z o - DIN EN 1334 - ICs

2、 97.140 Descriptors: Beds, mattresses, dimensions, measurement. Wohnmbel; Betten und Matratzen; Meverfahren und Toleranzempfehlungen European Standard EN 1334:1996 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been prepared by CEN/TC 207

3、. The responsible German body involved in its preparation was the Normenausschu Holzwirtschaft und Mbel (Timber and Furniture Standards Committee), Technical Committee Betten und Matratzen. EN comprises 4 pages. Eeuih Verlag GmbH, Berlin, has the exclusive right of sale for German Standards (DIN-Nor

4、men). 04.97 DIN EN 1334 Engl. Price group 5 Sales No. 11 05 EUROPEAN STANDARD NORME EUROPEENNE EUROPISCHE NORM EN 1334 March 1996 ICs 97.140 Descriptors: Beds, mattresses, dimensions, measurement. English version Domestic furniture Beds and mattresses Methods of measurement and recommeded tolerances

5、 Ameublement domestique; lits et matelas; mthodes de mesure et tolrances recom- mandes Wohnmbel; Betten und Matratzen; Me- verfahren und Toleranzempfehlungen This European Standard was approved by GEN on 1996-02-09. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipu

6、late the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard ex

7、ists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards b

8、odies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Se

9、cretariat: rue de Stassart 36, B-IO50 Brussels O 1996. CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN 1334:1996 E Page 2 EN 1334 : 1996 Contents Paga O Introduction 2 1 Scope . 2 2 Normative references 2 3 Definitions . 2 4 Gene

10、ral test conditions 3 5 Test equipment . 3 6 Methods of measurement 3 7 Recommended tolerances 3 8 Test report . 4 Foreword This European Standard has been prepared by Technical Committee CEN/TC 207 Furniture, the Secretariat of which is held by IBN. The text forms part of a series of standards spec

11、ifying requirements and the performance of beds and mattresses. This European Standard shall be given the status of a national Standard, either by publication of an identical text or by endorsement, and conflicting national standards withdrawn, by September 1996 at the latest. In accordance with the

12、 CENKENELEC Internal regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland

13、, and the United Kingdom. O Introduction This European Standard has been prepared in order to establish a method for the determination of the essential dimensions of mattresses, bed frames, divans and bed bases. Given the fact that a large variety of bed designs exists in Europe, in order to help ma

14、nufacturers, retailers and con- sumers to get the correct fit between the bed components, a nominal dimension, D, has been introduced and toler- ances on nominal dimension are recommended. 1 Scope This European Standard describes a method of measure- ment for determining the dimensions of all types

15、of dornes- tic mattresses, bed frames, divans and bed bases intended for use by adults. It does not apply to air beds and water beds nor to mattress pads that are placed on top of the main support mattress. It also includes recommended tolerances based on any nominal dimension in order to ensure the

16、 correct fit be- tween the bed components. However, specific requirements apply to the dimensions of bed bases for bunkbeds and single beds for use at a height of the upper face of the bed base of 800mm and more above floor level (EN 747-1). 2 Normative references This European Standard incorporates

17、, by dated or undated reference, provisions from other publications. These nor- mative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European

18、 Standard only when incorporated in it by amendment or revision. For un- dated references, the latest edition of the publication re- ferred to applies. EN 747-1 Bunkbeds for domestic use. Part 1: Safety re- quirements 3 Definitions For the purposes of this standard, the following definitions apply:

19、3.1 facturer to describe the size of an item. nominal dimension: Dimension used by the manu- 3.2 unframed slat base: Bed base consisting of sepa- rate slats flexibly held together normally by means of tex- tile, rubber or plastic tape. NOTE: When loading one slat, the load is trans- ferred to the su

20、pport by that slat only. 3.3 framed base: Bed base consisting of slats, springs, etc. which are connected to a structural frame system. NOTE: When loading one component (e.g. a slat or a spring) only, the load is transmitted from the frame to the support. 3.4 framed sprung mattress: Upholstered bed

21、base consisting of springs, topped with fillings, on a rigid frame to be used in a bed frame or free-standing. 3.5 divan base: Upholstered bed base used without the need of any framework. It may be constructed with a spring filling or a solid top and may include drawers or storage facilities. Page 3

22、 EN 1334: 1996 4 General test conditions 4.1 Preparation The item shall be tested as delivered. If of the knock-down type, it shall be assembled according to the instructions supplied with the furniture. Assembly fittings shall be tightened before testing. Where items have been compressed by packagi

23、ng or stor- age, these shall be allowed to recover unconstrained for at least 24 hours or according to the manufacturers recom- mendations, whichever is the longest. 4.2 Measuring accuracy Forces shall be measured to an accuracy of *5% and di- mensions, to an accuracy of fl mm. 5 Test equipment 5.1

24、Support surface Rigid, horizontal, flat. For the mattress measurements, it shall have a smooth melamine surface. The dimensions of the support surface shall be greater than those of the item under test. 5.2 Lateral loading pads Rigid, rectangular and vertical: 300 mm in height and 500 mm in width. T

25、he loading pads shall be mounted on a horizontal force application device which can apply a force as specified in 6.1. Where dimensions, as the bottom of the item, are designed to be smaller than the top, the lower dimension can be measured using loading pads 50 mm in height and 500 mm in width. 5.3

26、 Square aluminium alloy tube 40 mm x 40 mm x 2 mm, approximately 3 m long, having a mass of 2,5 kg * 12,5 g. 6 Methods of measurement 6.1 External plan dimensions of mattresses and bed bases For measuring the length and width of mattresses, bed bases and divan bases, place the item on the support su

27、r- face (see 5.1). Position the loading pads (see 5.2) at as low a level as possible (in contact with the support surface) to opposite sides of the item and parallel to each other. Apply an horizontal inward force of 15 N to each pad and measure the distance between the loadings pads. For mattresses

28、 less than 50 mm in height, the force shall be 5 N. For the determination of width, three measurements shall be taken: - two with the centreline of the loading pads 250 mm from the end of the item, - one with the centreline of the loading pads coinciding with the centreline of the item. The width sh

29、all be the mean from three readings. For determination of length, the number of measurements depends on the width of the items as follows: - for width less than 1 O00 mm, one measurement shall be taken at the centreline of the item: - for width from 1 O00 to 1400 mm, measurements shall be taken with

30、 the centreline of the loading pads 250 mm from the edge of the item; - for width larger than 1400 mm, follow the procedure for width measurement. The length shall be the mean value (where relevant) of the two or three readings. The measurement positions for bed bases which fit into a bed frame shal

31、l always be those giving the maximum di- mensions. The length of unframed slat bases shall be measured with- out loading. 6.2 Internal plan demensions of bed frames Place the item on the support surface (see 5.1). Apply the same procedures as in 6.1 except that the loading pads are to be positioned

32、inside the frame and the forces applied outwards. The measurement positions relevant for the fit of bed bases shall always be those giving the minimum dimensions. NOTE: Owing to the design there may be different dimensions for the fit of the mattress and for the fit of the bed base. 6.3 Determinatio

33、n of the height of mattress and divan bases Place the item on the support surface (see 5.1). Rest the aluminium tube (see 5.3) diagonally on the mat- tress (or divan base) so that the centre of the tube coincides with the geometric centre of the top plane of the mattress or divan base. Measure the d

34、istances between the tube and the support surface at each corner of the item. Repeat on the other diagonal. The height shall be the mean of the four readings. 7 Recommended tolerances In order to ensure that the bed components fit together, the following tolerances to the nominal dimensions are reco

35、m- mended. 7.1 Internal frame dimension Width and length: DZ mm 7.2 Mattress to fit into a bed Width and length: mm Height: D: f10mm or lo%, whichever is lower 7.3 Framed bases and framed sprung mattress Width: mm Length: U:; mm 7.4 Divan bases Width and length: D k 20 mm Height: D f 10 mm 7.5 Mattr

36、esses to be placed on a divan base Width and length: D I20 mm Height: Df 10mm or lo%, whichever is lower 7.6 Unframed slat bases Width: D:yo mm Length: DI:;, mm Page 4 EN 1334 1996 8 Test report The test report shall include at least the following informa- tion: d) test results, in millimetres, according to clauses 6 and 7; e) information on any deviations from this standard; 9 the name and address of the test house; g) date of test. a) a reference to EN 1334; b) the unit tested (relevant data); c) description of condition of units on supply;