DIN EN 13160-5-2016 Leak detection systems - Part 5 Requirements and test assessment methods for in-tank gauge systems and pressurised pipework systems German version EN 13160-5 20.pdf

《DIN EN 13160-5-2016 Leak detection systems - Part 5 Requirements and test assessment methods for in-tank gauge systems and pressurised pipework systems German version EN 13160-5 20.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13160-5-2016 Leak detection systems - Part 5 Requirements and test assessment methods for in-tank gauge systems and pressurised pipework systems German version EN 13160-5 20.pdf（77页珍藏版）》请在麦多课文档分享上搜索。

1、December 2016 English price group 27No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 23.020.10; 23.040.99!%h7“259692

2、0www.din.deDIN EN 13160-5Leak detection systems Part 5: Requirements and test/assessment methods for intank gauge systems and pressurised pipework systems;English version EN 131605:2016,English translation of DIN EN 13160-5:2016-12Leckanzeigesysteme Teil 5: Anforderungen und Prf/Bewertungsmethoden f

3、r Tankinhaltsmesssysteme und druckbeaufschlagte Rohrleitungen;Englische Fassung EN 131605:2016,Englische bersetzung von DIN EN 13160-5:2016-12Systmes de dtection de fuites Partie 5: Exigences et mthodes dessai/dvaluation des systmes de dtection de fuites en citernes et des systmes de tuyauterie sous

4、 pression;Version anglaise EN 131605:2016,Traduction anglaise de DIN EN 13160-5:2016-12SupersedesDIN EN 131605:200412See start of applicationwww.beuth.deDocument comprises 77 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.12.1

5、6 DIN EN 13160-5:2016-12 2 A comma is used as the decimal marker. Start of application The start of application of this standard is 2016-12-01. It should be noted that, in Germany, CE conformity marking of construction products will be permitted once this standard has been listed in the Official Jou

6、rnal of the European Union and/or the Bundesanzeiger (German Federal Gazette) and from the date given therein. For further information, users of this standard should refer to the websites of the European Commission or of the relevant building authority. The standard which this document replaces, DIN

7、 EN 13160-5:2004-12, may be used in parallel with this standard during a specified transition period where such has been laid down in the Official Journal of the European Union and/or the Bundesanzeiger (German Federal Gazette). National foreword This document (EN 13160-5:2016) has been prepared by

8、Technical Committee CEN/TC 393 “Equipment for storage tanks and for filling stations” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was DIN-Normenausschuss Tankanlagen (DIN Standards Committee Tank Installations), Working Committee NA 104-02-03 AA Leckanzeigege

9、rte. It should be noted that the original English reference version contains an error in C.1. In the German version; a correction is given in a national footnote. The corresponding English text should correctly read as follows: “C.1 Preparation This equipment is then used throughout the duration of

10、testing to ensure that all tests are conducted within the range of environmental conditions specified in 4.1 of EN 13352:2012, as appropriate to the location in which the components of the system under test are installed.” Amendments This standard differs from DIN EN 13160-5:2004-12 as follows: a) t

11、he requirement for a device for simulating a leak has been deleted; b) requirements that were included in the September 2003 edition of DIN EN 13160-1 but that have been omitted from the December 2016 edition have been adopted in this part of DIN EN 13160; c) pressure line leak detection kits have b

12、een included. The DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 8601 DIN ISO 8601 DIN EN 13160-5:2016-12 3 Previous editions DIN EN 13160-5: 2004-12 National Annex NA (informative) Bibliography 1 DIN ISO 8601, Data elements and interchange f

13、ormats Information interchange Representation of dates and times DIN EN 13160-5:2016-12 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13160-5 July 2016 ICS 23.020.10; 23.040.99 Supersedes EN 13160-5:2004English Version Leak detection systems - Part 5: Requir

14、ements and test/assessment methods for in-tank gauge systems and pressurised pipework systems Systmes de dtection de fuites - Partie 5: Exigences et mthodes dessai/dvaluation des systmes de dtection de fuites en citernes et des systmes de tuyauterie sous pression Leckanzeigesysteme - Teil 5: Anforde

15、rungen und Prf-/Bewertungsverfahren fr Tankinhaltsmesssysteme und druckbeaufschlagte Rohrleitungen This European Standard was approved by CEN on 8 April 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard th

16、e status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, Fren

17、ch, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria,

18、 Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey

19、and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref.

20、 No. EN 13160-5:2016 EEN 13160-5:2016 (E) 2 Contents Page European foreword . 5 1 Scope 6 2 Normative references 6 3 Terms, definitions, symbols and abbreviated terms 7 3.1 Terms and definitions . 7 3.2 Symbols and abbreviated terms 7 4 Requirements . 7 4.1 Effectiveness of leak detection kits 7 4.1

21、.1 General 7 4.1.2 Electrical or signal cable of the measuring device 8 4.1.3 Leak detection kit 8 4.1.4 Measures volumetric loss . 8 4.1.5 Requirements for software 9 4.1.6 Mechanical construction . 10 4.1.7 Effects of thermal contraction . 10 4.1.8 Alarm device 10 4.2 Durability of effectiveness 1

22、0 4.2.1 Durability of effectiveness against temperature 10 4.2.2 Durability of effectiveness against chemical attack 10 4.2.3 Durability of effectiveness against hydraulic shock (only for measuring devices used on pressurized line) 10 4.2.4 Durability of effectiveness against fatigue and mechanical

23、weardegradation, (only for measuring devices used on pressurized line) 10 4.2.5 Durability of effectiveness against microbiological growth on critical surfaces involved in the measurement process . 10 5 Testing, assessment and sampling methods 11 5.1 Effectiveness of leak detection kits . 11 5.1.1 G

24、eneral . 11 5.1.2 Disconnection of the electrical or signal cable of the measuring device . 11 5.1.3 Leak detection kit. 11 5.1.4 Measures volumetric loss 11 5.1.5 Software . 25 5.1.6 Mechanical construction . 25 5.1.7 Effects of thermal contraction . 26 5.1.8 Alarm Device 26 5.2 Durability of Effec

25、tiveness 26 5.2.1 Durability of effectiveness against temperature 26 5.2.2 Durability of effectiveness against chemical attack 26 5.2.3 Durability of effectiveness against hydraulic shock (only for measuring devices used on pressurized line) 28 5.2.4 Durability of effectiveness against fatigue and m

26、echanical weardegradation, (only for measuring devices used on pressurized line) 28 5.2.5 Durability of effectiveness against microbiological growth on critical surfaces involved in the measurement process . 29 6 Assessment and verification of constancy of performance AVCP . 29 DIN EN 13160-5:2016-1

27、2 EN 13160-5:2016 (E) 3 6.1 General . 29 6.2 Type testing 29 6.2.1 General . 29 6.2.2 Test samples, testing and compliance criteria . 30 6.2.3 Test reports 30 6.2.4 Shared other party results 31 6.2.5 Cascading determination of the product type results . 31 6.3 Factory production control (FPC) . 32

28、6.3.1 General . 32 6.3.2 Requirements . 33 6.3.3 Product specific requirements 35 6.3.4 Procedure for modifications . 36 6.3.5 One-off products, pre-production products (e.g. prototypes) and products produced in very low quantity . 36 7 Marking, labelling and packaging . 37 Annex A (normative) Acqui

29、sition of field data to provide a standard database for testing software leak detection systems Category A 38 A.1 Objective 38 A.2 Requirements . 39 A.3 Equipment . 40 A.4 Method 41 A.5 Data up-loading and verification 43 A.6 Induced leak rates quantitative systems 44 A.7 Induced leak rates qualitat

30、ive systems . 44 A.8 Test sequence . 44 A.9 Simulated leak test results 45 A.10 Qualification for use 45 A.11 Statistical analysis 46 Annex B (informative) Acquisition of field data to provide a standard database for testing software leak detection systems Category B(2) 51 B.1 General . 51 B.2 File

31、sorting and selection . 51 B.3 Data set Requirements . 51 B.4 Induced leak rates quantitative systems 52 B.5 Induced leak rates qualitative systems . 52 B.6 Test sequence . 52 B.7 Evaluation of simulated leak test results . 53 B.8 Qualification for use 53 B.9 Statistical analysis 53 B.10 Comparison

32、of variable and constant leak rate pairs . 56 B.11 Validation of conditions of use 57 DIN EN 13160-5:2016-12 EN 13160-5:2016 (E) 4 Annex C (normative) Leak detection systems Category B(1) 59 C.1 Preparation 59 C.2 Stabilization and trial run . 59 C.3 Procedure 59 C.4 Test results . 62 C.5 Evaluation

33、 . 63 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive Construction Products Regulation 305/2011/EU 65 ZA.1 Scope and relevant characteristics 65 ZA.2 Procedure for AVCP of leak detection systems based on volumetric loss from within th

34、e tank and/or pipework system . 66 ZA.2.1 System(s) of AVCP 66 ZA.2.2 Declaration of performance (DoP) 67 ZA.2.2.1 General 67 ZA.2.2.2 Content. 67 ZA.2.2.3 Example of DoP . 68 ZA.3 CE marking and labelling 70 Bibliography . 73 DIN EN 13160-5:2016-12 EN 13160-5:2016 (E) 5 European foreword This docum

35、ent (EN 13160-5:2016) has been prepared by Technical Committee CEN/TC 393 “Equipment for storage tanks and for filling stations”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorse

36、ment, at the latest by January 2017, and conflicting national standards shall be withdrawn at the latest by April 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifyi

37、ng any or all such patent rights. This document supersedes EN 13160-5:2004. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s),

38、see informative Annex ZA, which is an integral part of this document. According to EN 13160-5:2004 the following fundamental changes are given: Requirement for a device for simulating a leak deleted; requirements from EN 13160-1:2003 included, which are no longer contained in EN 13160-1:2016; Pressu

39、re line leak detection kits included. This European Standard, Leak detection systems, consists of 7 parts: Part 1: General principles Part 2: Requirements and test/assessment methods for pressure and vacuum systems Part 3: Requirements and test/assessment methods for liquid systems for tanks Part 4:

40、 Requirements and test/assessment methods for sensor based leak detection systems Part 5: Requirements and test/assessment methods for in-tank gauge systems and pressurized pipework systems Part 6: Sensors in monitoring wells Part 7: Requirements and test/assessment methods for leak detection lining

41、s According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, G

42、ermany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 13160-5:2016-12 EN 13160-5:2016 (E) 6 1 Scope This European Standard gives req

43、uirements and corresponding testassessment methods applicable to leak detection kits, based on volumetric loss from within the tank and/or pipework system. The kits usually comprise: Measuring Device Evaluation Device Alarm Device Intended use: Leak Detection kits are intended to be used inwith sing

44、le or double skin underground tanks or single or double skin underground and/or aboveground pipework designed for flammable liquids having a flash point not exceeding 100 C. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indis

45、pensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 228, Automotive fuels Unleaded petrol Requirements and test methods EN 590, Automotive fuels Diesel Require

46、ments and test methods EN 976-1, Underground tanks of glass-reinforced plastics (GRP) Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels Part 1: Requirements and test methods for single wall tanks EN 981:1996+A1:2008, Safety of machinery System of auditory and

47、visual danger and information signals EN 12285-1, Workshop fabricated steel tanks Part 1: Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and non-flammable water polluting liquids EN 13160-1:2016, Leak detection systems Part 1: General principles EN

48、13160-2, Leak detection systems Part 2: Requirements and test/assessment methods for pressure and vacuum systems EN 13352:2012, Specification for the performance of automatic tank contents gauges EN 14879-4:2007, Organic coating systems and linings for protection of industrial apparatus and plants a

49、gainst corrosion caused by aggressive media Part 4: Linings on metallic components EN 60296, Fluids for electrotechnical applications Unused mineral insulating oils for transformers and switchgear (IEC 60296) EN 60529, Degrees of protection provided by enclosures (IP Code) (IEC 60529) EN 61672-1, Electroacoustics Sound level meters Part 1: Specifications (IEC 61672-1) DIN EN 13160-5:2016-12