DIN EN 131-7-2013 Ladders - Part 7 Mobile ladders with platform German version EN 131-7 2013《梯子 第7部分 带平台的移动梯子 德文版本EN 131-7-2013》.pdf

《DIN EN 131-7-2013 Ladders - Part 7 Mobile ladders with platform German version EN 131-7 2013《梯子 第7部分 带平台的移动梯子 德文版本EN 131-7-2013》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 131-7-2013 Ladders - Part 7 Mobile ladders with platform German version EN 131-7 2013《梯子 第7部分 带平台的移动梯子 德文版本EN 131-7-2013》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、September 2013 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).

2、ICS 97.145!%(q“2059478www.din.deDDIN EN 131-7Ladders Part 7: Mobile ladders with platform;English version EN 131-7:2013,English translation of DIN EN 131-7:2013-09Leitern Teil 7: Mobile Podestleitern;Englische Fassung EN 131-7:2013,Englische bersetzung von DIN EN 131-7:2013-09chelles Partie 7: chell

3、es mobiles avec plate-forme;Version anglaise EN 131-7:2013,Traduction anglaise de DIN EN 131-7:2013-09www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 22 pages 08.13 DIN EN 131-7:2013-09 2 A comma is used as the decimal marker. Start of

4、application The start of application of this standard is 2013-09-01. National foreword This standard includes safety requirements within the meaning of the Produktsicherheitsgesetz (ProdSG) (German Product Safety Act). This document (EN 131-7:2013) has been prepared by Technical Committee CEN/TC 93

5、“Ladders” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Holzwirtschaft und Mbel (Timber and Furniture Standards Committee), Working Committee NA 042-04-20 AA Spiegelausschuss zu CEN/TC 93 Leitern. Where this standard has been identified

6、by the Ausschuss fr Produktsicherheit (German Committee for Product Safety) and reference to it has been published in the Gemeinsames Ministerialblatt (German Joint Ministerial Gazette) by the Bundesanstalt fr Arbeitsschutz und Arbeitsmedizin (BAuA) (German Federal Institute for Occupational Safety

7、and Health), it is to be presumed that mobile ladders with platform which comply with this standard fulfil the relevant health and safety requirements. Where they comply with the provisions laid down in Section 5 of the Product Safety Act, such products may then be marked with the GS mark (German “s

8、afety tested” mark) as awarded to the manufacturer by an authorized “GS organization”. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 131-7 July 2013 ICS 97.145 English Version Ladders - Part 7: Mobile ladders with platform chelles - Partie 7: chelles mobiles avec plate-forme Leitern - Teil 7:

9、 Mobile Podestleitern This European Standard was approved by CEN on 15 May 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and b

10、ibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the res

11、ponsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav R

12、epublic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NO

13、RMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 131-7:2013: EEN 131-7:2013 (E) 2 Contents Page Foreword 3 1 Scope 3 2 Normative re

14、ferences 3 3 Terms and definitions .3 4 Requirements .6 4.1 General 6 4.2 Surface finishes .6 4.3 Materials .6 4.4 Stabiliser .7 4.5 Ballast .7 5 Dimensional requirements 7 5.1 Ascending legs 7 5.2 Supporting legs 8 5.3 Platform and toe board .8 5.4 Working area 8 5.5 Wheels and castors .9 5.6 Preve

15、ntion of falls: Guardrails, Middle rails .9 5.7 Handrails 10 6 Testing . 11 6.1 General . 11 6.2 Torsion test of steps, rungs, wide rungs . 11 6.3 Bending test for steps, rungs, wide rungs . 11 6.4 Platform and complete product test . 12 6.5 Protection bending test 14 6.6 Side handrail testing 14 6.

16、7 Stability test . 14 6.8 Stiffness test . 16 6.9 Test for products equipped with spring wheels 17 6.10 Kick-up test of the platform . 18 6.11 Test of opening restraint devices . 18 6.12 Test of hooks . 18 6.13 Bottom stile end test 18 6.14 Feet pull test 18 6.15 Test method for plastic ladders 18 6

17、.16 Marking durability . 18 7 Marking, User and safety instruction . 19 7.1 Marking 19 7.2 User Instruction 19 Bibliography . 20 DIN EN 131-7:2013-09 EN 131-7:2013 (E) 3 Foreword This document (EN 131-7:2013) has been prepared by Technical Committee CEN/TC 93 “Ladders”, the secretariat of which is h

18、eld by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2014, and conflicting national standards shall be withdrawn at the latest by January 2014. Attention is drawn to the possibility

19、 that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This European Standard is one of a series about ladders. The other Standards of this series are listed in Clause 2 and in t

20、he Bibliography. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Maced

21、onia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. 1 Scope This European Standard defines terms and specifies the general

22、 design characteristics of mobile ladders with platform. It applies to mobile ladders with a working platform, with a maximum area of 1 m2, and a maximum platform height of 5 m, to be used only by one person at the time. The maximum load is 150 kg which includes a maximum combined load of the user a

23、nd any tools, equipment and materials It does not apply to portable ladders according to EN 131-1, to portable ladders according to EN 131-4, to portable ladders for fire service use according to EN 1147, to loft ladders according to EN 14975, to step stools according to EN 14183, to Stairs, steplad

24、ders and guard-rails according to EN ISO 14122-3 and to insulating ladders according to EN 50528. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited a

25、pplies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 131-2, Ladders Part 2: Requirements, testing, marking EN 131-3, Ladders - Part 3: User Instructions 3 Terms and definitions For the purposes of this document, the following terms and

26、definitions apply. DIN EN 131-7:2013-09 EN 131-7:2013 (E) 4 Table 1 Terms and definitions Dimensions in millimetres No Term Definition Figure 3.1 ascending leg leg of a ladder with climbing supports Figure 1 3.2 supporting leg leg of a ladder without climbing supports 3.3 stile lateral part of a lad

27、der which supports the rungs or steps as well as cross struts of supporting legs 3.4 preventions from falls 3.4.1 guard rail device to hold and protect from falls, installed on the platform of mobile platform ladders 3.4.2 middle rail element of the guard rail, placed between the top rail and the pl

28、atform 3.4.3 gate at the ascending leg rigid or flexible device, parallel to the platform, to hold and to protect from falls 3.5 platform topmost standing surface which is different from a step Figure 2 3.6 toe board side protection fixed at the platform or the guard rail 3.7 handrail device for mob

29、ile ladders parallel to the ascending leg, which allows a secure grip during the ascending/descending 3.8 wheel device to facilitate the movement of the mobile platform ladder Note 1 to entry: Wheels can be: used only use for transportation; or used for transportation and as load bearing element; fi

30、tted with brakes. 3.9 stabiliser device to increase the stability of the mobile platform ladder DIN EN 131-7:2013-09 EN 131-7:2013 (E) 5 3.10 ballast permanent/fixed load applied to the mobile platform ladder used to increase its resistance to overturning 3.11 angle of inclination of the ascending l

31、eg angle between the floor and the imaginary line joining the upper edges of the sides of the front steps Figure 3 3.12 distance between the bottom end and the lowest rung/wide rung/ step l4distance from the lower end of the ladder to the upper edge of the lowest rung/wide rung/step, measured in the

32、 middle line between the stiles 3.13 distance between rungs/wide rungs/steps l5distance between the rungs/wide rungs/steps and between the top rung/wide rung/step and the platform measured in the middle line between the stiles at the upper edges 3.14 climbing height h vertical distance between the g

33、round and the top of the platform measured vertically when all feet are in contact with the ground 3.15 inner width of ascending leg b1usable distance between the inner sides of the stiles measured at the level of the platform 3.16 Rung (g) climbing support with a standing surface from front to back

34、 of less than 50 mm and at least 20 mm Figure 4 3.17 wide rung (g) climbing support with a standing surface from front to back equal to or greater than 50 mm and less than 80 mm Figure 5 3.18 Step (g) climbing support with a standing surface from front to back equal to or greater than 80 mm DIN EN 1

35、31-7:2013-09 EN 131-7:2013 (E) 6 Figure 6 3.19 distance between the bottom end and the lowest rung/ wide rung/ step h1vertical distance between the floor and the top of the first rung/wide rung/step Figure 7 3.20 distance between rungs/ wide rungs/ steps h2vertical distance between the rungs/wide ru

36、ngs/steps and between the top rung/wide rung/step and the platform measured in the middle line between the stiles at the upper edges 3.21 clearance e clearance between two rungs of consecutive ascending legs 4 Requirements 4.1 General A mobile platform ladder shall be designed and manufactured to pr

37、event accidental slips of product and/or user. The marking shall be legible and durable. The durability of the marking shall be verified. Wide rungs/steps and platforms shall be designed to be horizontal when the product is used on a flat floor. Wide rungs, rungs, steps and platforms made of metal o

38、r plastics shall have a textured surface on the working face to reduce slipping. The contact surface of the coverings shall adhere firmly to the rungs or steps. 4.2 Surface finishes This requirement shall be according EN 131-2. The coating of wooden parts shall be transparent and permeable to water

39、vapour. This does not apply to platform components manufactured from plywood materials. 4.3 Materials 4.3.1 General The requirements on materials shall be according to EN 131-2 apply unless otherwise stated. 4.3.2 Wood Wood used for the platform should be of durable quality and be suitable for both

40、indoor and outdoor use. The coating shall be transparent and permeable to water vapour. DIN EN 131-7:2013-09 EN 131-7:2013 (E) 7 Coatings applied to platform components manufactured from plywood materials shall be permeable to water but may be opaque. The surface of the platform shall be slip resist

41、ant. 4.4 Stabiliser If the design makes stabilisers necessary to fulfil the stability test requirements, they shall be supplied with the ladder. It shall be clear that the product is meant to be used with stabilisers. Specific safety instruction shall be visible on the ladder and may be repeated on

42、the stabilisers. 4.5 Ballast If the design makes ballasts necessary to fulfil the stability test requirements, they shall be supplied with the ladder. It shall be clear that the product is meant to be used with a ballast. Specific safety instruction shall be visible on the ladder and may be repeated

43、 on the ballast. 5 Dimensional requirements 5.1 Ascending legs 5.1.1 Ascending legs with angle 60 75 The dimensional requirements for ascending legs angle 60 75are shown in Table 2. Table 2 Dimensional requirements for ascending legs with angle 60 75 Dimensions in millimetres b1h g l4l5min. 400 20 0

44、,5 l5230 max. 5 000 l5+ 15 300 This product is ascended and descended facing the ladder. Handrails can be added to this product. 5.1.2 Ascending legs with angle 45 0,5 m2This test shall be carried out in addition to the previous test described in 6.4.1.1. If the platform area is more than 0,5 m2, pu

45、t 2 loads of each 2 600 N on two plates of max. 100 mm 100 mm distributed equally in the middle of the platform (see Figure 13). Requirement: no disassembly, cracking or rupture shall occur. NOTE This load is applied for the foreseeable misuse of the platform by two people. Figure 13 Platform test f

46、or platform area 0,5 m26.4.2 Complete product test The product is placed in the use position. The stability devices/ ballast shall be fitted in position. Place the test load F = 3 500 Nin the middle of the ascending leg uniformly distributed on the surface of the rung/wide rung/step for a period of

47、1 min (see Figure 14). Requirement: no disassembly, cracking or rupture shall occur. DIN EN 131-7:2013-09 EN 131-7:2013 (E) 14 Figure 14 Complete product test 6.5 Protection bending test 6.5.1 Tests on guardrails (principal guardrails and top handrail of the gate) To eliminate the free movements app

48、ly a preload of 20 N horizontally for a period of 1 min. The position of the handrail under the preload is the starting point for the measurement of bending. Apply the test load of 300 N horizontally for one minute distributed over a length of 100 mm and a depth equal to the principal guardrail in the most unfavourable position and direction, and then measure the deflection. Requirement: maximum deflection under load 35 mm. Apply the test load of 1 250N vertically for one minute distributed over