DIN EN 1269-2016 Textile floor coverings - Assessment of impregnations in needled floor coverings by means of a soiling test German version EN 1269 2015《铺地织物 通过沾污试验评估针织地板覆盖物的渗透性 德文.pdf

《DIN EN 1269-2016 Textile floor coverings - Assessment of impregnations in needled floor coverings by means of a soiling test German version EN 1269 2015《铺地织物 通过沾污试验评估针织地板覆盖物的渗透性 德文.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1269-2016 Textile floor coverings - Assessment of impregnations in needled floor coverings by means of a soiling test German version EN 1269 2015《铺地织物 通过沾污试验评估针织地板覆盖物的渗透性 德文.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、February 2016 English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 59.080.60!%LS9“2414822www.din.de

2、DIN EN 1269Textile floor coverings Assessment of impregnations in needled floor coverings by means of a soiling test;English version EN 1269:2015,English translation of DIN EN 1269:2016-02Textile Bodenbelge Beurteilung von Ausrstungsmitteln in Nadelvliesbelgen durch die Anschmutzneigung;Englische Fa

3、ssung EN 1269:2015,Englische bersetzung von DIN EN 1269:2016-02Revtements de sol textiles valuation des imprgnations des revtements de sol aiguillets au moyen dun essai dencrassement;Version anglaise EN 1269:2015,Traduction anglaise de DIN EN 1269:2016-02SupersedesDIN EN 1269:2008-04www.beuth.deDocu

4、ment comprises 10 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.03.16 DIN EN 1269:2016-02 2 A comma is used as the decimal marker. National foreword This document (EN 1269:2015) has been prepared by Technical Committee CEN/TC

5、 134 “Resilient, textile and laminate floor coverings” (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was DIN-Normenausschuss Kunststoffe (DIN Standards Committee Plastics), Working Committee NA 054-04-09 AA Textile Bodenbelge. The DIN Standards corresponding to

6、 the International Standards referred to in this document are as follows: ISO 105-A02 DIN ISO 20105-A02 ISO 565 DIN ISO 565 Amendments This standard differs from DIN EN 1269:2008-04 as follows: a) Clause 2 “Normative references” has been updated; b) in Subclause 4.2.1, the “drum” inner diameter has

7、been changed to (205 5) mm (previously (200 10) mm) and an inner height of (200 10) mm has been specified (applies only to the German version); c) in Subclause 4.3.1 “Standard soil”, the composition of the soil and the colourimetric characteristics have been amended; d) the standard has been editori

8、ally revised. Previous editions DIN EN 1269: 1997-05, 2008-04 National Annex NA (informative) Bibliography DIN EN 20105-A02, Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour DIN ISO 565, Test sieves Metal wire cloth, perforated metal plate and electroformed shee

9、t Nominal sizes of openings EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1269 November 2015 ICS 59.080.60 Supersedes EN 1269:1997English Version Textile floor coverings - Assessment of impregnations in needled floor coverings by means of a soiling test Revtements de sol textiles - valuation

10、des imprgnations des revtements de sol aiguillets au moyen dun essai dencrassement Textile Bodenbelge - Beurteilung von Ausrstungsmitteln in Nadelvliesbelgen durch die Anschmutzneigung This European Standard was approved by CEN on 26 September 2015. CEN members are bound to comply with the CEN/CENEL

11、EC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or

12、 to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the offi

13、cial versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,

14、 Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of

15、exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1269:2015 EEN 1269:2015 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Principle . 4 4 Apparatus . 4 4.1 Method A. 4 4.1.1 Castor chair apparatus, . 4 4.1.2 Soil distrib

16、utor . 4 4.2 Method B. 5 4.2.1 Drum 5 4.2.2 Tetrapod . 5 4.2.3 Driving system . 5 4.3 Equipment common to both methods . 6 4.3.1 Standard soil . 6 4.3.2 Vacuum cleaner . 6 4.3.3 Large dimension grey scales . 6 4.3.4 Apparatus . 6 5 Sampling and preparation of the specimens . 6 5.1 Sampling and selec

17、tion of the specimens . 6 5.2 Preparation of the specimen . 7 5.2.1 Method A. 7 5.2.2 Method B. 7 6 Conditioning 7 7 Procedure. 7 7.1 Method A. 7 7.2 Method B. 8 8 Expression of results 8 9 Test report . 8 DIN EN 10303:2016-02 EN 1269:2015 (E) 3 European foreword This document (EN 1269:2015) has bee

18、n prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2016, a

19、nd conflicting national standards shall be withdrawn at the latest by May 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This d

20、ocument supersedes EN 1269:1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav R

21、epublic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 10303:2016-02 EN 1269:2015 (E) 4 1 Scope This E

22、uropean Standard specifies two methods for the evaluation of impregnations or other treatments in needled floorcoverings by means of a soiling test. There is no correlation known between the two soiling methods. 2 Normative references The following documents, in whole or in part, are normatively ref

23、erenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 985, Textile floor coverings Castor chair test EN 1471:1996, Textile

24、floor coverings Assessment of changes in appearance EN ISO 139, Textiles Standard atmospheres for conditioning and testing (ISO 139) ISO 105-A02, Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour ISO 565, Test sieves Metal wire cloth, perforated metal plate and e

25、lectroformed sheet Nominal sizes of openings ISO 1957, Machine-made textile floor coverings Selection and cutting of specimens for physical tests 3 Principle In both tests a fixed quantity of standard artificial soil is scattered over the surface of the specimens which is also subjected to the rolli

26、ng action of castors or of tetrapod feet for a specified time. After vacuum cleaning, the degree of colour change is assessed by comparing the contrast between treated and untreated test specimens with the contrast of the grey scale. Depending on the type of apparatus available, either method A or m

27、ethod B can be used. 4 Apparatus 4.1 Method A 4.1.1 Castor chair apparatus, As described in EN 985, with a total load of 60 daN. 4.1.2 Soil distributor The soil distributor uses two sieves, one inside and resting on the other to distribute the soil evenly on the part of the circular specimen that is

28、 subjected to the wear action of the castors. The whole distributor is placed vertically above the specimen with the sieves in the horizontal position. The soil is placed in the inner sieve which is vibrated relative to the larger outer sieve thereby achieving even distribution of the soil on the sp

29、ecimen below the two sieves. The mesh size of both sieves is 0,5 mm (module 31 of ISO 565). The base of each sieve (each of which has walls) is in the shape of a regular trapezium in order to correspond to a sector of the treated area of the test specimen. The outer (lower) sieve has following base

30、dimensions: DIN EN 10303:2016-02 EN 1269:2015 (E) 5 distance between the parallel sides: 220 mm; length of the parallel sides: 100 mm, 45 mm. Its underside is 40 mm above the specimen. The dimensions of the inner (upper) sieve are not specified but shall be smaller than the base sieve to permit move

31、ment relative to the lower sieve. 4.2 Method B 4.2.1 Drum A rigid cylindrical drum with bottom and lid shall be used. The inner diameter is (205 5) mm and the inner height of the drum is (200 10) mm. The drum is made of polyvinylchloride (PVC), with a thickness of at least 6 mm. The bottom and lid a

32、re attached to the wall by appropriate means. The lid of the drum is preferably made of transparent material, e.g. Polymethylmethacrylate (PMMA.). 4.2.2 Tetrapod A tumbler consisting of a central metal sphere with four outer feet arranged in the shape of a regular tetrahedron. Each foot is covered w

33、ith a spherical polyurethane cap. In operation the tetrapod tumbles inside the rotating drum so that the feet impact on the test specimen lining the drum. Tetrapod specifications: total mass: (1 000 25) g; angle between any two legs: 109,5; length of the foot: (62 2) mm; diameter of the foot: (47 2)

34、 mm; length of the metal leg: 32 mm; diameter of the metal leg: 25 mm; socket depth of the foot: 20 mm; free standing height tetrapod: (124 2) mm; material of the feet: polyurethane elastomer; hardness of the foot top: (75 5) shore. 4.2.3 Driving system The drum lies loose on rollers mounted on a su

35、pport and drive shaft. The drum is prevented from moving in its axial direction by smooth running wheels fixed between the shafts or by a suitable profile on the rollers. It is important that the axis of the drum rotation is horizontal, which should be checked by placing a spirit level along the upp

36、er surface of the drum when in position. The rotational frequency of the drum shall be (50 2) cycles per minute. A counter is incorporated in the system, so that the number of rotations of the drum can be recorded. The counter may be pre-set to stop the apparatus after a given number of revolutions.

37、 DIN EN 10303:2016-02 EN 1269:2015 (E) 6 NOTE Longer driving rollers can be used to rotate a number of drums at the same time provided that all the requirements of this standard are met. 4.3 Equipment common to both methods 4.3.1 Standard soil The soil shall have the following composition (% by mass

38、): Quartz silica: 88,30 %; Kaolin: 9,35 %; Yellow ferrous oxide: 0,20 %; Black ferrous oxide: 0,60 %; Paraffin oil: 1,55 %. The soil shall have following colourimetric characteristics: L: 46,5 1,5; a: 4,2 0,3; b: 11,5 0,5. Since the colourimetric characteristics of the soil change with time and expo

39、sure to light, the soil shall be kept in the dark and its colourimetric characteristics (L, a, b) shall be checked every 6 months against the specified tolerances. 4.3.2 Vacuum cleaner A household type apparatus shall be used, equipped with a smooth, approximately 2 500 mm2section nozzle having the

40、following characteristics: partial vacuum = (1 900 190) mm water column; air flow rate = (30 3) dm3/s 4.3.3 Large dimension grey scales A set of large dimension grey scales including half degrees according to ISO 105-A02. 4.3.4 Apparatus An observation device according to Clause 5 in EN 1471:1996. 5

41、 Sampling and preparation of the specimens 5.1 Sampling and selection of the specimens Take a representative sample of four different coloured samples from the commercial range of the floor covering in accordance with the methods given in ISO 1957. DIN EN 10303:2016-02 EN 1269:2015 (E) 7 5.2 Prepara

42、tion of the specimen 5.2.1 Method A From each sample to be examined, cut two test specimens in the shape of a quadrant having a radius of 350 mm. The edges of the quadrant are cut parallel with and at right angles to the direction of manufacture. One of the two specimens is kept as a reference speci

43、men for the evaluation. Mark the two specimens with an arrow on the back (e.g. the direction of production) to permit alignment in the same direction for assessment. The quadrants are fixed onto the support (dimensionally stable flat plastic disk) using two strips of double-sided adhesive tape laid

44、overlapping the joints. In the case of self-adhesive tiles place them on the support without any additional adhesive. 5.2.2 Method B From each sample to be examined, cut two test specimens of (640 190) mm. The length is taken in the direction of production. One of the two specimens is kept as a refe

45、rence specimen for assessment, the other one is used for the soiling test in the tetrapod-drum. Cover the long sides of this specimen with a 20 mm wide tape. 6 Conditioning Condition the test specimens in the standard atmosphere specified in EN ISO 139, for at least 24 h. 7 Procedure 7.1 Method A a)

46、 Clean the specimens using the vacuum cleaner (4.3.2) before placing them onto the castor chair apparatus. Place the soil distributor above the specimen. b) Weigh out 10 g of standard soil (4.3.1); rotate the support plate of the apparatus without lowering the castor device; carefully put the standa

47、rd soil into the inner sieve by means of a spatula, so that it is evenly distributed over the whole surface of the sieve. c) Vibrate the sieve so as to spread out the soil evenly over the whole surface of the specimen. d) Lower the castor apparatus with a total loading of 60 daN until it rests on th

48、e support and then rotate the plate 100 cycles without reversal so as to spread out the soil and make it penetrate. e) Raise the castors and remove the specimen support from the apparatus. f) Clean the specimen with the vacuum cleaner (4.3.2) using a forwards and backwards motion for 5 s in each dir

49、ection. Repeat this 10 times. Examine the treated specimen and if the soil is not distributed evenly on the specimen repeat the test with a new specimen. g) On the same specimens a second soil treatment shall be applied. Repeat all of the operation b) to f) by using the opposite direction of rotation in d). h) Remove the specimens from the support and assess the colour change g