DIN EN 12591-2009 Bitumen and bituminous binders - Specifications for paving grade bitumens English version of DIN EN 12591 2009-08《沥青和沥青粘合剂 铺路级沥青规范 英文版本DIN EN 12591-2009-08》.pdf

《DIN EN 12591-2009 Bitumen and bituminous binders - Specifications for paving grade bitumens English version of DIN EN 12591 2009-08《沥青和沥青粘合剂 铺路级沥青规范 英文版本DIN EN 12591-2009-08》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 12591-2009 Bitumen and bituminous binders - Specifications for paving grade bitumens English version of DIN EN 12591 2009-08《沥青和沥青粘合剂 铺路级沥青规范 英文版本DIN EN 12591-2009-08》.pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、August 2009DEUTSCHE NORM English price group 14No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 93.080.20!$Y6“1541997ww

2、w.din.deDDIN EN 12591Bitumen and bituminous binders Specifications for paving grade bitumensEnglish version of DIN EN 12591:2009-08Bitumen und bitumenhaltige Bindemittel Anforderungen an StraenbaubitumenEnglische Fassung DIN EN 12591:2009-08SupersedesDIN EN 12591:2000-04See start of validitywww.beut

3、h.deDocument comprises 31 pagesDIN EN 12591:2009-08 Start of validity This standard is due to take effect on 1 August 2009. It should be noted that, in Germany, CE conformity marking of construction products will be permitted once this standard has been listed in the Bundesanzeiger (German Federal G

4、azette) and from the date given therein. National foreword This standard has been prepared by Technical Committee CEN/TC 336 “Bituminous binders” (Secretariat: AFNOR, France). The responsible German bodies involved in its preparation were the Normenausschuss Materialprfung (Materials Testing Standar

5、ds Committee) and the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Joint Technical Committee NA 062-03-32 GA Bitumen; Prfverfahren und Anforderungen fr die Bindemittel. Amendments This standard differs from DIN EN 12591:2000-04 as follows: a) Tables 1 to 3 relating

6、to paving grade bitumen specifications have been revised and divided up into Tables 1A, 1B, 2A, 2B, 3A and 3B. b) Clause 6 “Evaluation of conformity” has been added. c) Annex A “Special national conditions” has been deleted. d) Annex ZB “A-deviations” has been deleted. e) Annex ZA “Clauses of this E

7、uropean Standard addressing the provisions of the EU Construction Products Directive” has been added. Previous editions DIN 1995: 1929, 1934, 1941-11, 1960x-02, 1980-12 DIN 1995-1: 1989-10 DIN 1995-2: 1989-10 DIN EN 12591: 2000-04 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12591 April 20

8、09 ICS 93.080.20; 91.100.50 Supersedes EN 12591:1999 English Version Bitumen and bituminous binders Specifications for paving grade bitumens Bitumes et liants bitumineux Spcifications des bitumes routiers Bitumen und bitumenhaltige Bindemittel Anforderungen an Straenbaubitumen This European Standard

9、 was approved by CEN on 14 March 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such

10、national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language a

11、nd notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembou

12、rg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights o

13、f exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12591:2009: EEN 12591:2009 (E) 2 Contents PageForeword 3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Sampling .6 5 Requirements and test methods 6 6 Evaluation of

14、conformity 14 Annex A (normative) Calculation of the penetration index, Ip. 17 Annex B (informative) Complementary information on grade selection 19 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive . 20 Bibliography . 29 DIN

15、 EN 12591:2009-08 EN 12591:2009 (E) 3 Foreword This document (EN 12591:2009) has been prepared by Technical Committee CEN/TC 336 “Bituminous binders”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an ident

16、ical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by October 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held

17、responsible for identifying any or all such patent rights. This document supersedes EN 12591:1999. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Construction Product Directive

18、 (89/106/EEC). For relationship with EU Construction Product Directive (89/106/EEC), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Eu

19、ropean Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the Unit

20、ed Kingdom. This European Standard is part of a family of European Standards for bitumen as follows: NOTE Industrial applications are not covered by mandate M/124. Bituminous binders Paving Grade Bitumens EN 12591rev Oxidized Bitumens (industrial applications) EN 13304 Hard GradeIndustrialBitumens (

21、industrial applications)EN 13924 HardPaving Grade Bitumens PolymerModifiedBitumensEN 14023 EN 13305Cut-back b) Consistency at elevated service temperature; c) Durability of consistency. The properties of “adhesion“ and “setting ability“ are indicated by tests used on either the finished asphalt mixt

22、ures or on aggregate-bitumen combinations, i.e. EN 126971, EN 1269711, EN 1269712, EN 12697 26 1 to 4, rather than tests on the bitumen itself. This European Standard still consists of specifications based upon traditional test methods. Work programs are being undertaken to evaluate alternative prop

23、erties and test methods in order to develop new specifications that are more directly performance-related. The progress of those work programmes are reported in CEN/TR 15352 17, and the results will be considered for future revisions of this European Standard. DIN EN 12591:2009-08 EN 12591:2009 (E)

24、5 1 Scope This European Standard provides a framework for specifying a range of properties and relevant test methods for bitumens, which are suitable for use in the construction and maintenance of roads, airfields and other paved areas, together with requirements for evaluation of conformity. This E

25、uropean Standard does not directly address cohesion, adhesion and setting ability (see Introduction). NOTE Although industrial bitumens are specified according to EN 13305, it should be underlined that paving grade bitumens, specified according to this European Standard, can also be used for industr

26、ial applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 58, B

27、itumen and bituminous binders Sampling bituminous binders EN 1426, Bitumen and bituminous binders Determination of needle penetration EN 1427, Bitumen and bituminous binders Determination of the softening point Ring and Ball method EN 12592, Bitumen and bituminous binders Determination of solubility

28、 EN 12593, Bitumen and bituminous binders Determination of the Fraass breaking point EN 12594, Bitumen and bituminous binders Preparation of test samples EN 12595, Bitumen and bituminous binders Determination of kinematic viscosity EN 12596, Bitumen and bituminous binders Determination of dynamic vi

29、scosity by vacuum capillary EN 12597, Bitumen and bituminous binders Terminology EN 12607-1, Bitumen and bituminous binders Determination of the resistance to hardening under the influence of heat and air Part 1: RTFOT method EN 12607-2, Bitumen and bituminous binders Determination of the resistance

30、 to hardening under the influence of heat and air Part 2: TFOT method EN 15326, Bitumen and bituminous binders Measurement of density and specific gravity Capillary-stoppered pyknometer method EN ISO 2592, Determination of flash and fire points Cleveland open cup method (ISO 2592:2000) EN ISO 2719,

31、Determination of flash point Pensky-Martens closed cup method (ISO 2719:2002) EN ISO 4259, Petroleum products Determination and application of precision data in relation to methods of test (ISO 4259:2006) EN ISO 9001:2000, Quality management systems Requirements (ISO 9001:2000) DIN EN 12591:2009-08

32、EN 12591:2009 (E) 6 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12597:2000 apply. 4 Sampling Samples of bulk products shall be taken as described in EN 58. Test samples shall be taken from the laboratory samples, and prepared for testing, as descr

33、ibed in EN 12594. 5 Requirements and test methods 5.1 General European product standards cover a large variety of road materials for different applications, to accommodate local traffic loads and climatic conditions. This European Standard therefore also covers a large range of bitumens to facilitat

34、e the production and application of the designed paving. The variety of production techniques and applications makes it more practical to split bitumens into three separate tables. The requirements for the properties for a specific grade shall be selected from Table 1A, Table 1B, Table 2A, Table 2B,

35、 Table 3A and Table 3B by choosing a column representing the specified values or ranges. There is a subdivision of properties into two groups in the tables. The properties in Table 1A, Table 2A and Table 3A shall be specified for all paving grade bitumens. They are associated with regulatory or HSE

36、requirements. The properties in Table 1B, Table 2B and Table 3B are required to meet specific regional conditions. They are associated with regulatory or other regional requirements. Two severity levels for resistance to hardening are stated as alternatives as, under specific conditions, a larger in

37、crease in softening point after Rolling Thin Film Oven Test (RTFOT) may be allowed (i.e. Severity level 2) without detrimental effect if this increase is associated with requirements for Fraass breaking point or penetration index (Ip) or both. NOTE For complementary information on grade selection, s

38、ee Annex B. 5.2 Properties and related test methods 5.2.1 General The properties of paving grade bitumens and related test methods shall be in accordance with Table 1A and Table1B, or Table 2A and Table 2B or Table 3A and Table 3B. When tested by the methods given in the Tables, the various paving g

39、rades shall conform to the limits specified. The grades are designated by the nominal penetration or viscosity ranges as appropriate. 5.2.2 Consistency at intermediate service temperature Consistency at intermediate service temperature shall conform to the requirements for penetration value in Table

40、 1A or Table 2A. 5.2.3 Consistency at elevated service temperature Consistency at elevated service temperature shall conform to the requirements for softening point in Table 1A (penetration graded), softening point or dynamic viscosity in Table 2A (penetration graded), or kinematic viscosity in Tabl

41、e 3A (kinematic viscosity graded). DIN EN 12591:2009-08 EN 12591:2009 (E) 7 5.2.4 Brittleness at low service temperature Brittleness at low service temperature may be required to meet specific regional conditions in countries susceptible to extreme cold. Where required, paving grade bitumens shall c

42、onform to the requirements for Fraass breaking point in Table 1B or Table 2B. 5.2.5 Temperature dependence of consistency Temperature dependence of consistency may be required to meet specific regional conditions. Where required, paving grade bitumens shall conform to the requirement for dynamic vis

43、cosity or penetration index (Ip) or both in Table 1B. 5.2.6 Durability Resistance to hardening Durability is demonstrated by compliance with the required surrogate characteristics of “Resistance to hardening”, defined in Table 1A, Table 2A or Table 3B. Resistance to hardening shall be tested accordi

44、ng to the Rolling Thin Film Oven Test (RTFOT) in accordance with EN 12607-1 for binders from Table 1A and Table 2A. Resistance to hardening shall be tested according to the Thin Film Oven Test (TFOT) in accordance with EN 12607-2 for binders from Table 3A. 5.2.7 Other properties 5.2.7.1 Density Alth

45、ough requirements for the density of paving grade bitumens are not given in this document, density shall be determined, when necessary, in accordance with EN 15326. 5.2.7.2 Flash point Flash point shall be determined by the Cleveland open cup method in EN ISO 2592 for binders in Table 1A and by the

46、Pensky-Martens closed cup method, EN ISO 2719, for binders in Table 2A and Table 3A. NOTE For bitumens in Table 1A, the Pensky-Martens closed cup method may be used to investigate possible contamination but is likely to give lower values than the Cleveland open cup method. 5.3 Release of dangerous r

47、egulated substances Materials used in products shall not release any dangerous substances in excess of the maximum permitted levels specified in a relevant European Standard for the material or permitted in the national regulations of the member state of destination. 5.4 Precision The test methods r

48、eferred to in this document include precision statements when available. In cases of uncertainty, the procedures described in EN ISO 4259 for interpretation of the results based on test method precision shall be used. DIN EN 12591:2009-08 EN 12591:2009 (E) 8 Table 1A Paving grade bitumen specificati

49、ons for grades from 20 x 0,1 mm to 220 x 0,1 mm penetration Properties applying to all paving grade bitumen listed in this table Property Test method Unit 20/30 30/45 35/50 40/60 50/70 70/100 100/150 160/220 Penetration at 25 C EN 1426 0,1 mm 20 30 30 45 35 50 40 60 50 70 70 100 100 150 160 220 Softening point EN 1427 C 55 63 52 60 50 58 48 56 46 54 43 51 39 47 35 43 Resistance to hardening at 163 C EN 12607-1 Retained penetration % 55 53 53 50 50 46 43 37