DIN EN 12350-10-2010 Testing fresh concrete - Part 10 Self-compacting concrete - L box test German version EN 12350-10 2010《新拌混凝土试验 第10部分 自充填混凝土 L箱试验 德文版本EN 12350-10-2010》.pdf

《DIN EN 12350-10-2010 Testing fresh concrete - Part 10 Self-compacting concrete - L box test German version EN 12350-10 2010《新拌混凝土试验 第10部分 自充填混凝土 L箱试验 德文版本EN 12350-10-2010》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 12350-10-2010 Testing fresh concrete - Part 10 Self-compacting concrete - L box test German version EN 12350-10 2010《新拌混凝土试验 第10部分 自充填混凝土 L箱试验 德文版本EN 12350-10-2010》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、December 2010 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 91.100.30!$lx“1738557www.din.deDDIN EN 12350-10Testing fresh concrete Part 10: Self-compacting concrete L box testEnglish translation of DIN EN 12350-10:2010-12Prfung von Frischbeton Teil 10: Selbstverdichtender Beton L-Kasten-VersuchEnglische bersetzung von DIN EN 12350-10:2010-12Essai pour bton

3、frais Partie 10: Bton auto-plaant Essai la bote en LTraduction anglaise de DIN EN 12350-10:2010-12www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1212.10 DIN EN 12350-10:2010-12 A comma is used as the decimal marker. National forew

4、ord This standard has been prepared by Technical Committee CEN/TC 104 “Concrete and related products” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-0

5、7-02 AA Prfverfahren fr Beton. The DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 5725-2 DIN ISO 5725-2 National Annex NA (informative) Bibliography DIN ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results Part 2:

6、Basic method for the determination of repeatability and reproducibility of a standard measurement method 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12350-10 July 2010 ICS 91.100.30 English Version Testing fresh concrete - Part 10: Self-compacting concrete - L box test Essai pour bton fra

7、is - Partie 10: Bton auto-plaant - Essai la bote en L Prfung von Frischbeton - Teil 10: Selbstverdichtender Beton - L-Kasten-Versuch This European Standard was approved by CEN on 20 June 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions fo

8、r giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three offici

9、al versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria,

10、Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN

11、COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12350-10:2010: EEN 12350-10:2010

12、(E) 2 Contents Page Foreword 31 Scope 52 Normative references 53 Principle 54 Apparatus .55 Test sample 76 Test procedure .77 Test result .88 Test report 89 Repeatability and reproducibility .8Bibliography . 10DIN EN 12350-10:2010-12 EN 12350-10:2010 (E) 3 Foreword This document (EN 12350-10:2010) h

13、as been prepared by Technical Committee CEN/TC 104 “Concrete and related products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2011, and confl

14、icting national standards shall be withdrawn at the latest by January 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This docum

15、ent has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). This standard is based on the results from the EU-project “Testing-SCC“ under the 5thFrame Programme (GRD2-2000-30024/G6RD-CT

16、-2001-00580). Owing to its significant advantages in the improvement of construction quality and working environment, self-compacting concrete (SCC) has been widely accepted by the construction owners. The use of SCC in practical concrete construction is steadily increasing. Since SCC has to give sa

17、tisfactory in-situ properties (perfect filling of the mould and embedment of the reinforcement, homogeneity and full compaction) without vibration, the proper methods for testing the fresh SCC are very important. These should address three key properties: filling ability, passing ability and resista

18、nce to segregation. It is desirable, especially in the case of new constituents or new concrete compositions, to test the consistence of fresh SCC before casting in place. A number of test methods including this test are available for testing fresh SCC. Most of the commonly used test methods were ev

19、aluated in the recently closed EU-project “Testing-SCC“ under the 5thFrame Programme (GRD2-2000-30024/G6RD-CT-2001-00580). According to the results from this EU project, it seems no single test method can completely cover all three key properties. Nevertheless any test method should at least be corr

20、elated to the practical situation and give consistent results in order to provide reliable data for judgment of concrete consistence. This standard is one of a series concerned with testing fresh concrete. EN 12350, Testing fresh concrete, consists of the following parts: Part 1: Sampling Part 2: Sl

21、ump-test Part 3: Vebe test Part 4: Degree of compactability Part 5: Flow table test Part 6: Density Part 7: Air content Pressure methods Part 8: Self-compacting concrete Slump-flow test DIN EN 12350-10:2010-12 EN 12350-10:2010 (E) 4 Part 9: Self-compacting concrete V-funnel test Part 10: Self-compac

22、ting concrete L box test Part 11: Self-compacting concrete Sieve segregation test Part 12: Self-compacting concrete J-ring test CAUTION When cement is mixed with water, alkali is released. Take precautions to avoid dry cement entering the eyes, mouth and nose whilst mixing concrete. Prevent skin con

23、tact with wet cement or concrete by wearing suitable protective clothing. If cement or concrete enters the eye, immediately wash it out thoroughly with clean water and seek medical treatment without delay. Wash wet concrete off the skin immediately. According to the CEN/CENELEC Internal Regulations,

24、 the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Net

25、herlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 12350-10:2010-12 EN 12350-10:2010 (E) 5 1 Scope This European Standard specifies the procedure for determining the passing ability ratio for self-compacting concrete using the L

26、 box test. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12350-1, Tes

27、ting fresh concrete Part 1: Sampling 3 Principle The L box test is used to assess the passing ability of self-compacting concrete to flow through tight openings including spaces between reinforcing bars and other obstructions without segregation or blocking. There are two variations; the two bar tes

28、t and the three bar test. The three bar test simulates more congested reinforcement. A measured volume of fresh concrete is allowed to flow horizontally through the gaps between vertical, smooth reinforcing bars. The heights of the concrete in the vertical section (H1) and at the end of the horizont

29、al section (H2), see Figure 1, are measured and the ratio H2/H1determined. This ratio is a measure of the passing or blocking behaviour of SCC . 4 Apparatus 4.1 L box, having the general arrangement and internal dimensions as shown in Figure 1. The L box shall be of rigid construction with surfaces

30、that are smooth, flat and not readily attacked by cement paste or be liable to rusting. The vertical hopper may be removable for ease of cleaning. The bar positioning system shall be such that two smooth steel bars of (12 0,2) mm diameter will provide a gap of (59 1) mm for the two bar test and thre

31、e smooth steel bars of (12 0,2) mm diameter will provide a gap of (41 1) mm for the three bar test. The system shall locate the bars in the L box so that they are vertical and equidistant across the width of the box, as shown in Figure 2. DIN EN 12350-10:2010-12 EN 12350-10:2010 (E) 6 Dimensions in

32、millimetres Key 1 Sliding gate Figure 1 Typical general assembly of L box showing required dimensions DIN EN 12350-10:2010-12 EN 12350-10:2010 (E) 7 Dimensions in millimetres a) Clear bar space, (41 1) mm b) Clear bar space, (59 1) mmKey 1 12 0,2 mm diameter smooth steel bars Figure 2 Bar positions

33、in L box The surface of any material used in the assemblies shall not be readily attacked by cement paste or be liable to rusting. 4.2 Rule or measuring tape, of minimum length 500 mm and graduated at intervals not exceeding 1 mm, the zero mark being at the extreme end of the rule or measuring tape.

34、 4.3 Containers, to hold the sample and having a total volume not less than 14 l. 4.4 Spirit level, for checking horizontality of base of L box base prior to commencing the test. 4.5 Straight edge, for striking off concrete level with the top of the L box. 5 Test sample A sample of at least 14 l sha

35、ll be obtained in accordance with EN 12350-1. 6 Test procedure Support the L box on a level base and check for horizontality using the spirit level. Clean the L box and dampen immediately prior to testing, but keep free from excess moisture. Close the gate between the vertical and horizontal section

36、s. Pour the concrete from the container(s) into the filling hopper of the L box, without any agitation or mechanical compaction, then strike off the top with the straight edge so that the concrete is level with the top of the vertical section of the L box and allow to stand for (60 10) s. Check the

37、concrete for signs of segregation before and after filling of the L box and report under item 8, d) in a qualitative way, e.g. no indication of segregation, strong indication of segregation. NOTE Signs of segregation include a layer of cement paste/mortar and segregated coarse aggregate at the top.

38、Fully open the sliding gate in a smooth continuous action to allow the concrete to flow into the horizontal section. When movement has ceased, measure the drop in height of the level of concrete H1 to the nearest 1 mm in the vertical section on the gate side of the box at three positions equally spa

39、ced across the width of the box. The mean depth of the concreteH1 is the difference between the height of vertical section and the average of the three readings of H1. Record H1to the nearest 1 mm. The same procedure is used to calculate the mean depth of the concrete at the end of the horizontal se

40、ction of the L box H2from the DIN EN 12350-10:2010-12 EN 12350-10:2010 (E) 8 difference with the height of the horizontal section and the average of the three readings of H2. Record H2to the nearest 1 mm. 7 Test result The passing ability ratio PL, as measured by the L box test, is calculated to the

41、 nearest 0,01 from the following equation: 12HHPL = where PL is the passing ability ratio measured by the L box test; H1is the mean depth of concrete in the vertical section of the box, in millimetres; H2is the mean depth of concrete at the end of the horizontal section of the box, in millimetres. 8

42、 Test report The test report shall include: a) identification of the test sample; b) location where the test was performed; c) date and time of test; d) any segregation or bleeding observed during filling of the L box; e) whether two bar or three bar test; f) passing ability ratio, PL, to the neares

43、t 0,05; g) any deviation from the standard test method; h) declaration by the person technically responsible for the test that it was carried out in accordance with this standard, except as noted in item g). The report may include: i) temperature of the concrete at the time of test; j) age of concre

44、te at time of test (if known). 9 Repeatability and reproducibility The repeatability r and reproducibility R have been determined by a programme including eleven laboratories, 22 operators and two replicates, and interpreted in accordance with ISO 5725-2. The resulting values for r and R for the thr

45、ee bar test are given in Table 1. DIN EN 12350-10:2010-12 EN 12350-10:2010 (E) 9 Table 1 Repeatability and reproducibility for typical values of the passing ability ratio Passing ability ratio PL 0,8 0,8 Repeatability r 0,11 0,13 Reproducibility R 0,12 0,16DIN EN 12350-10:2010-12 EN 12350-10:2010 (E) 10 Bibliography 1 ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability of a standard measurement method DIN EN 12350-10:2010-12