DIN EN 12348-2010 Core drilling machines on stand - Safety German version EN 12348 2000+A1 2009《立式岩芯钻机 安全性 德文版本EN 12348-2000+A1-2009》.pdf

《DIN EN 12348-2010 Core drilling machines on stand - Safety German version EN 12348 2000+A1 2009《立式岩芯钻机 安全性 德文版本EN 12348-2000+A1-2009》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 12348-2010 Core drilling machines on stand - Safety German version EN 12348 2000+A1 2009《立式岩芯钻机 安全性 德文版本EN 12348-2000+A1-2009》.pdf（33页珍藏版）》请在麦多课文档分享上搜索。

1、January 2010DEUTSCHE NORM English price group 15No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 25.080.40!$|,“1568909w

2、ww.din.deDDIN EN 12348Core drilling machines on stand Safety (includes Amendment A1:2009)English version of DIN EN 12348:2010-01Kernbohrmaschinen auf Stnder Sicherheit (enthlt nderung A1:2009)Englische Fassung DIN EN 12348:2010-01SupersedesDIN EN 12348:2000-11www.beuth.deDocument comprises pages33St

3、art of validity This standard takes effect on 1 January 2010. National foreword This standard includes safety requirements. This standard has been prepared by Technical Committee CEN/TC 151 “Construction equipment and building material machines Safety” (Secretariat: DIN, Germany). The responsible Ge

4、rman body involved in its preparation was the Normenausschuss Maschinenbau (Mechanical Engineering Standards Committee), Working Committee NA 060-13-06 AA Baugerte of Section Bau- und Baustoffmaschinen. Representatives of manufacturers and users of machines and equipment to process building material

5、s and of the employers liability insurance associations contributed to this standard. This standard contains specifications meeting the essential requirements set out in Annex I of the “Machinery Directive”, Directive 98/37/EC (valid until 28 December 2009), and the “revised Machinery Directive”, Di

6、rective 2006/42/EC, which takes effect on 29 December 2009, and which apply to machines that are either first placed on the market or commissioned within the EEA. This standard serves to facilitate proof of compliance with the essential requirements of the directives. Once this standard is cited in

7、the Official Journal of the European Union, it is deemed a “harmonized” standard and thus, a manufacturer applying this standard may assume compliance with the requirements of the Machinery Directive (“presumption of conformity”). The European and International Standards referred to in clause 2 and

8、in the bibliography have been published as the corresponding DIN EN, DIN EN ISO or DIN ISO Standards with the same number. For the International Standard ISO 16031-1 referred to in this standard, there is no national standard available. Amendments This standard differs from DIN EN 12348:2000-11 as f

9、ollows: a) The foreword has been revised. b) Subclause 7.1 “Marking” has been revised. c) In subclause A.6, the sound pressure level has been brought in line with Directive 2006/42/EC. d) Annex D “Vibration test code” has been added. e) Annex ZA (informative) “Relationship between this European Stan

10、dard and the Essential Requirements of EU Directive 98/37/EC” has been updated. f) Annex ZB (informative) “Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC” has been included. Previous editions DIN EN 12348: 2000-11 2 DIN EN 12348:2010-01 EUROPEAN

11、 STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12348:2000+A1 April 2009 ICS 25.080.40 Supersedes EN 12348:2000English Version Core drilling machines on stand Safety Foreuses bton (carotteuses) sur colonne Scurit Kernbohrmaschinen auf Stnder Sicherheit This European Standard was approved by CEN on 26 J

12、une 2000 and includes Amendment 1 approved by CEN on 1 March 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical

13、 references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN me

14、mber into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

15、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 B

16、russels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12348:2000+A1:2009: EEN 12348:2000+A1:2009 (E) 2 Contents Page Foreword 3Introduction .41 Scope 42 Normative references 53 Terms and definitions .64 List of significant h

17、azards 85 Safety requirements and/or measures . 105.1 Mechanical hazards 105.2 Electrical hazards . 135.3 Ergonomics . 135.4 Thermal hazards . 135.5 Exhaust fumes (internal combustion engine machines) and exhaust compressed air (pneumatic machines) 145.6 Hydraulic and pneumatic machines . 145.7 Flui

18、d containers 145.8 Water supply and dust emission . 145.9 Rotational speed . 145.10 Noise 155.11 !Vibration 155.12 Maintenance 156 Verification of safety requirements and/or measures . 157 Information for use . 157.1 Marking 167.2 Accompanying documents 16Annex A (normative) Noise test code - Grade

19、2 of accuracy. 20Annex B (normative) Pictograms . 23Annex C (normative) Verification of surface temperature . 24Annex D (normative) !Vibration test code . 25Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC“ 29Annex ZB (inform

20、ative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“ 30Bibliography . 31DIN EN 12348:2010-01 EN 12348:2000+A1:2009 (E) 3 Foreword This document (EN 12348:2000+A1:2009) has been prepared by Technical Committee CEN/TC 151 “Construction equipmen

21、t and building material machines - Safety“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withd

22、rawn at the latest by December 2009. This document includes Amendment 1, approved by CEN on 2009-03-01. This document supersedes EN 12348:2000. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. This European Standard has been prepared under a manda

23、te given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). !For relationship with EU Directives, see informative Annexes ZA and ZB, which are integral parts of this document.“ The annex A is normative and contains “Nois

24、e test code - Grade 2 of accuracy“, annex B is normative and contains “Pictograms“, annex C is normative and contains “Verification of surface temperature“, and the annex ZA is informative and contains Relationship of this European Standard with EU Directives“. This European Standard also contains a

25、 Bibliography. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, I

26、reland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. DIN EN 12348:2010-01 EN 12348:2000+A1:2009 (E) 4 Introduction This European standard is a Type C-standard as stated in !EN ISO 12100

27、-1“. The machinery concerned and the extent to which hazards are covered are indicated in the scope of this standard. This European standard has been prepared by taking into account the safety requirements of EN 791:1995 which are applicable to core drilling machines on a stand. 1 Scope This Europea

28、n Standard applies to core drilling machines on transportable stands equipped with a diamond core drill bit, usually with a water supply connection device, and intended to drill holes into stone, concrete and similar mineral materials in a stationary position where the power for the tool rotation is

29、 supplied by an electrical, hydraulic, pneumatic or internal combustion prime motor. The feed movement of the drill head and core drill bit may be effected by manual, mechanical or hydraulic means. This European Standard deals with all significant hazards pertinent to core drilling machines on a sta

30、nd when used as intended and under the conditions foreseen by the manufacturer (see clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. This standard does not apply to: percussive or rotary-percussive rock drills ei

31、ther mounted or unmounted; hand held power drills; hydraulic or pneumatic power supply sources; mobile undercarriages to which machines can be fitted. This European Standard does not apply to machinery covered by EN 791:1995. This European Standard covers electrical hazards by making reference to re

32、levant European Standards (see 5.2). Those hazards that are relevant for all mechanical, electrical, hydraulic and other equipment of machinery and that are dealt with in standards for common use are not covered by this European Standard. Reference to pertinent standards of this kind is made where s

33、uch standards are applicable and so far as is necessary. In this European Standard, core drilling machines on a stand are called “machines“ and diamond core drill bits are called “tools”. NOTE The term “diamond“ is used as a generic word which covers all varieties of abrasive products such as diamon

34、d, borum nitride. This European Standard applies primarily to machines which are manufactured after the date of approval of the standard by CEN. DIN EN 12348:2010-01 EN 12348:2000+A1:2009 (E) 5 2 Normative references !The following referenced documents are indispensable for the application of this d

35、ocument. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.“ !deleted text“ !EN 206-1:2000, Concrete Part 1: Specification, performance, production and conformity“ EN 294:1992, Safety of mach

36、inery - Safety distances to prevent danger zones being reached by the upper limbs !deleted text“ EN 791:1995, Drill rigs - Safety !EN 953“, Safety of machinery Guards - General requirements for the design and construction of fixed and movable guards !deleted text“ EN 982:1996, Safety of machinery -

37、Safety requirements for fluid power systems and their components - Hydraulics EN 983:1996, Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics !EN 12096, Mechanical vibration Declaration and verification of vibration emission values“ !deleted text“ !pr

38、EN ISO 3744:2006, Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering method in an essentially free field over a reflecting plane (ISO/DIS 3744:2006)“ !EN ISO 5349-2:2001, Mechanical vibration Measurement and evaluation of human exp

39、osure to hand-transmitted vibration Part 2: Practical guidance for measurement at the workplace (ISO 5349-2:2001) EN ISO 8041, Human response to vibration Measuring instrumentation (ISO 8041:2005)“ EN ISO 11201:1995, !Acoustics Noise emitted by machinery and equipment Measurement of emission sound p

40、ressure levels at a work station and at other specified positions Engineering method in an essentially free field over a reflecting plane (ISO 11201:1995)“ !EN ISO 12100-1:2003, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003

41、) EN ISO 12100-2:2003, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12100-2:2003) EN ISO 13732-1:2008, Ergonomics of the thermal environment Methods for the assessment of human responses to contact with surfaces Part 1: Hot surfaces (ISO 13732-1

42、:2006) EN ISO 13849-1:2008, Safety of machinery Safety-related parts of control systems Part 1: General principles for design (ISO 13849-1:2006) EN ISO 13850:2008, Safety of machinery Emergency stop Principles for design (ISO 13850:2006) DIN EN 12348:2010-01 EN 12348:2000+A1:2009 (E) 6 EN ISO 20643:

43、2008, Mechanical vibration Hand-held and hand-guided machinery Principles for evaluation of vibration emission (ISO 20643:2005)“ !EN 60204-1:2006, Safety of machinery Electrical equipment of machines Part 1: General requirements (IEC 60204-1:2005, modified)“ !EN 60335-1:2002, Household and similar e

44、lectrical appliances Safety Part 1: General requirements (IEC 60335-1:2001, modified)“ !EN 60335-2-41:2003, Household and similar electrical appliances Safety Part 2-41: Particular requirements for pumps (IEC 60335-2-41:2002)“ EN 61029-1:2000, Safety of transportable motor operated electric tools Pa

45、rt 1: General requirements (IEC 61029-1:1990, modified) !prEN 61029-2-6:2007, Safety of transportable motor-operated electric tools Part 2-6: Particular requirements for diamond drills with water supply (IEC 61029-2-6:1993, modified)“ !ISO 5348, Mechanical vibration and shock Mechanical mounting of

46、accelerometers ISO 7000:2004, Graphical symbols for use on equipment Index and synopsis ISO 16063-1, Methods for the calibration of vibration and shock transducers Part 1: Basic concepts“ 3 Terms and definitions For the purposes of this European Standard the terms and definitions stated in !EN ISO 1

47、2100-1:2003“ apply. Additional terms and definitions specifically needed for this European Standard are added below. 3.1 core drilling machine machine used to drill holes with a diamond core bit into walls, floors and ceilings made of concrete, natural stone and other mineral building materials. The

48、 machine is mounted on a transportable stand having a drive spindle which is equipped with a core drill bit. It is (generally) equipped with a water supply. It may have manual or powered feed. Figure 1 shows a typical example of a core drilling machine DIN EN 12348:2010-01 EN 12348:2000+A1:2009 (E)

49、7 Key 1 Frame (drill stand) including a column which may be tiltable and a base 2 Drilling unit 3 Diamond core drill bit including any connecting accessories (not being part of the machine) 4 Control devices for the operating functions and feed mechanism of the machine 5 Water supply system 6 Residual current device (RCD) Figure 1 Main parts of a core drilling machine 3.2 drilling un