DIN EN 12320-2012 Building hardware Padlocks and padlock fittings Requirements and test methods German version EN 12320 2012《建筑五金件 挂锁及其配件 试验方法和要求 德文版本EN 12320-2012》.pdf

《DIN EN 12320-2012 Building hardware Padlocks and padlock fittings Requirements and test methods German version EN 12320 2012《建筑五金件 挂锁及其配件 试验方法和要求 德文版本EN 12320-2012》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 12320-2012 Building hardware Padlocks and padlock fittings Requirements and test methods German version EN 12320 2012《建筑五金件 挂锁及其配件 试验方法和要求 德文版本EN 12320-2012》.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、December 2012 Translation by DIN-Sprachendienst.English price group 13No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 91.190!$“1929994www.din.deDDIN EN 12320Building hardware Padlocks and padlock fittings Requirements and test methods;English version EN 12320:2012,English translation of DIN EN 12320:2012-12Baubeschlge Hangschlsser und Hangschlossbeschlge Anforderungen und Prfverfahren;Englische Fassung EN 12320:

3、2012,Englische bersetzung von DIN EN 12320:2012-12Quincaillerie pour le btiment Cadenas et porte-cadenas Exigences et mthodes dessai;Version anglaise EN 12320:2012,Traduction anglaise de DIN EN 12320:2012-12SupersedesDIN EN 12320:2001-05www.beuth.deDocument comprises pagesIn case of doubt, the Germa

4、n-language original shall be considered authoritative.291 .122 DIN EN 12320:2012-12 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling” (Secretariat: AFNOR, Franc

5、e), Working Group WG 4 “Building hardware” (lead-management: BSI, United Kingdom). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-09-40 AA Schlsser und Baubeschlge. Amendments Thi

6、s standard differs from DIN EN 12320:2001-05 as follows: a) in Subclauses 4.4 and 5.4.1, the classification according to the corrosion resistance has been extended; b) Table 2 “Security requirements” has been revised; c) Clause 5 “Test methods” has been harmonized with Clause 4 “Requirements”; d) Fi

7、gure 1 “The tool set” has been added. Previous editions DIN EN 12320: 2001-05 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12320 October 2012 ICS 91.190 Supersedes EN 12320:2001English Version Building hardware - Padlocks and padlock fittings - Requirements and test methods Quincaillerie pou

8、r le btiment - Cadenas et porte-cadenas -Exigences et mthodes dessai Baubeschlge - Hangschlsser und Hangschlossbeschlge - Anforderungen und Prfverfahren This European Standard was approved by CEN on 11 August 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipu

9、late the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European S

10、tandard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the

11、national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,

12、 Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reser

13、ved worldwide for CEN national Members. Ref. No. EN 12320:2012: EContents Page Foreword . 31 Scope 42 Normative references 43 Terms and definitions . 44 Requirements . 65 Test methods . 86 Classification . 167 Marking . 17Annex A (normative) Sampling and sequencing - Tests on alternative design padl

14、ocks 18Annex B (normative) Test rig illustrations 19DIN EN 12320:2012-12 EN 12320:2012 (E) 2 Foreword This document (EN 12320:2012) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This Eu

15、ropean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the latest by April 2013. Attention is drawn to the possibility that some of the eleme

16、nts of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12320:2001. The following is a list of technical changes since the previous edition: - Limited manual attack - Corrosi

17、on resistance - Table 2 security requirements - Resistance to attack by plug/cylinder extraction - Annex A, sampling and sequencing The test methods are specified in detail to ensure reproducibility at any testing establishment within Europe, and the acceptance criteria are defined objectively to en

18、sure consistency of assessment. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Re

19、public of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 12320:2012-12 EN 12320:2012 (E) 3 1 Scope This E

20、uropean Standard applies to mechanical padlocks and padlock fittings used on buildings and general use and specifies the test methods to be used. This European Standard specifies performance and other requirements for strength, security, durability, performance, and corrosion resistance of padlocks.

21、 It establishes one category of use, two categories of durability, six categories for corrosion resistance and six grades for security based on performance tests that simulate attack. Limited manual attack testing is included in this European Standard because the machine testing does not replicate a

22、ll known manual attacks. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu

23、ment (including any amendments) applies. EN 1303:2005, Building hardware Cylinders for locks Requirements and test methods EN 1670:2007, Building hardware Corrosion resistance Requirements and test methods EN 10025-2, Hot rolled products of structural steels Part 2: Technical delivery conditions for

24、 non-alloy structural steels ISO 10899, High-speed steel two-flute twist drills Technical specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions and symbols apply. 3.1 Terms and definitions 3.1.1 cam part of the key and cylinder mechanism which

25、operates the locking mechanism 3.1.2 effective key differ difference between the key mechanism of similar design, achieved only by the movable detainer, which allows each key mechanism to be operated only by its own key Note 1 to entry: The number of effective differs is equal to the number of theor

26、etical differs after deduction of the differs suppressed by the manufacturer due to technical constraints and those differs suppressed in accordance with the restraints of 4.5.1 3.1.3 hasp part of the padlock fitting which goes over the staple. DIN EN 12320:2012-12 EN 12320:2012 (E) 4 3.1.4 key mech

27、anism part of the mechanism which recognises a correct key 3.1.5 locking mechanism part of the mechanism which is operated by the key mechanism to lock/unlock the padlock 3.1.6 padlock independent locking device comprising a body, a key mechanism, a locking mechanism and a shackle 3.1.7 padlock fitt

28、ing device fitted to the object which is to be locked with a padlock excluding cables and chains 3.1.8 shackle part of the padlock which passes through and secures the padlock fitting 3.1.9 staple part of the padlock fitting through which the padlock shackle is passed. 3.2 Symbols Table 1 Symbol Uni

29、t Definitiond mm Diameter of shackle F1 kN Push/pull force on cylinder plug/locking mechanism F2 kN Pull force on shackle or staple F3 kN Cutting force on shackle or staple F4 kN Maximum possible push/pull force on cylinder plug/locking mechanismh mm Height through which weight is dropped (impact te

30、st) M1 Nm Torque on key to test for interpassing M2 Nm Torque on cylinder plug/locking mechanism M3 Nm Twisting torque on shackle or staple n Minimum number of effective key differs t min Drilling/sawing resistance time T C Temperature of product for impact testing m g Drop mass for impact test DIN

31、EN 12320:2012-12 EN 12320:2012 (E) 5 4 Requirements 4.1 General The structure of this clause reflects the classification as given in Clause 6. 4.2 Category of use (first classification digit) Grade 1: according to requirements in 5.2 4.3 Durability (second classification digit) Grade 0: no requireme

32、nts Grade 1: 10 000 cycles When tested in accordance with 5.3 it shall be possible to operate the padlock. The padlock fittings are excluded from the durability test. 4.4 Corrosion Resistance (third classification digit) Products shall be classified in accordance with EN 1670. Grade 0: no defined co

33、rrosion resistance Grade 1: 24h +1h/-0 h; Grade 2: 48h +1h/-0 h; Grade 3: 96h+1h/-0 h; Grade 4: 240h +1h/-0 h; Grade 5: 480h +1h/-0 h; After the corrosion test, the padlock shall operate using a maximum torque on the key of 2.5 Nm. This corrosion test shall apply to the functionality only (not appea

34、rance). 4.5 Security (fourth classification digit) 4.5.1 General Some of the requirements can be confirmed with a certificate and test report according to EN 1303. In grades 4, 5 and 6 it shall not be possible to remove the key until the shackle is deadlocked in the closed position and the key retai

35、ned in open position. 4.5.2 Minimum number of effective key differs Padlocks shall have a minimum of n effective key differs (Table 2). For a mechanical padlock, the maximum number of steps on the same level shall be 60 %, maximum two adjacent and a minimum of three levels. DIN EN 12320:2012-12 EN 1

36、2320:2012 (E) 6 4.5.3 Non-interpassing of keys with just one interval effective differ When tested in accordance with 5.5.2, it shall not be possible to operate the padlock with keys differing from the correct key by one interval, i.e. the next closest key. The next closest key shall be defined by t

37、he manufacturer according to its key coding system. 4.5.4 Resistance to force on cylinder plug or locking mechanism When tested in accordance with 5.5.3, the cylinder plug or the locking mechanism shall resist a force F1 (Table 2). 4.5.5 Resistance to torque on cylinder plug or locking mechanism Whe

38、n tested in accordance with 5.5.4, the cylinder plug or the locking mechanism shall resist a torque M2 (Table 2). 4.5.6 Resistance to pulling of shackle or staple When tested in accordance with 5.5.5, the shackle and the staple shall each resist a force F2 (Table 2). 4.5.7 Resistance to twisting of

39、shackle or staple When tested in accordance with 5.5.6, the shackle and the staple shall each resist a torque M3 (Table 2). 4.5.8 Resistance to cutting of shackle or staple When tested in accordance with 5.5.7, the shackle and the staple shall each resist a force F3 (Table 2). 4.5.9 Resistance to im

40、pact on padlock body, shackle and staple at low temperature When tested in accordance with 5.5.8, the padlock body, the shackle and the staple cooled to temperature T, shall each resist the blows from the steel pole with the mass m and from the height h (Table 2). 4.5.10 Resistance to drilling of pa

41、dlock body, shackle and staple When tested in accordance with 5.5.9, the padlock body, the shackle and the staple shall each resist drilling for a time t (Table 2). 4.5.11 Resistance to sawing of padlock body, shackle and staple When tested in accordance with 5.5.10, the padlock body, the shackle an

42、d the staple shall each resist sawing for a time t (Table 2). 4.5.12 Attack resistance When tested in accordance with 5.5.11, the padlock shall resist attacks with manual tools for a time t (see Table 2). DIN EN 12320:2012-12 EN 12320:2012 (E) 7 Table 2 Security requirements Require-ment clause numb

43、er Requirement Test method clause number Test parameter Grade Unit 1 2 3 4 5 6 4.5.1 Key retained in open position yes / no - - - yes yes yes 4.5.2 Minimum number of effective key differs 5.5.1 n 300 1 000 2 500 5 000 10 000 20 000 - 4.5.3 Non-interpassing of keys with just one interval differ - Tor

44、que on key 5.5.2 M1 1 1 1,5 1,5 1,5 1,5 Nm 4.5.4 Resistance to force on cylinder plug or locking mechanism 5.5.3 F1 - - 4 5 10 15 kN 4.5.5 Resistance to torque on cylinder plug or locking mechanism 5.5.4 M2 - 2,5 5 15 20 30 Nm 4.5.6 Resistance to pulling of shackle and staple 5.5.5 F2 3 5 15 30 70 1

45、00 kN 4.5.7 Resistance to twisting of shackle and staple 5.5.6 M3 40 100 200 600 1 200 2 500 Nm 4.5.8 Resistance to cutting of shackle and staple 5.5.7 F3 6 15 25 45 70 100 kN 4.5.9 Resistance to impact on padlock body, shackle and staple at low temperature 5.5.8 T m h - - - - - - - 20 1 250 800 - 2

46、0 3 050 1 000 - 40 6 550 1 400 - 40 7 150 1 500 C g mm 4.5.10 Resistance to drilling of padlock body, shackle and staple 5.5.9 t - - - 2 4 8 min 4.5.11 Resistance to sawing of padlock body, shackle and staple 5.5.10 t - - - 2 4 8 min 4.5.12 Manual attack 5.5.11 t toolsets - - - 3 5 10 min NOTE Class

47、ification is in six grades where grade 1 has the lowest requirement. 5 Test methods 5.1 General 5.1.1 Introduction The manufacturer will provide assembly and component drawings to enable the tester to carry out a preliminary product assessment prior to testing. The padlock shall be tested in the loc

48、ked position with the key removed. It is not necessary for the correct key to operate the padlock after testing. Padlocks/ padlock fittings and their original keys shall be taken at random and submitted for each test. In the event of one of the original two samples failing the test, the padlocks/ padlock fittings shall be deemed to have failed and a further two shall be tested, both of which shall pass the test. DIN EN 12320:2012-12 EN 12320:2012 (E) 8 If the parts