DIN EN 12259-3-2001 Fixed firefighting systems - Components for sprinkler and water spray systems - Part 3 Dry alarm valve assemblies (includes Amendment A1 2001) German version EN.pdf

《DIN EN 12259-3-2001 Fixed firefighting systems - Components for sprinkler and water spray systems - Part 3 Dry alarm valve assemblies (includes Amendment A1 2001) German version EN.pdf》由会员分享，可在线阅读，更多相关《DIN EN 12259-3-2001 Fixed firefighting systems - Components for sprinkler and water spray systems - Part 3 Dry alarm valve assemblies (includes Amendment A1 2001) German version EN.pdf（45页珍藏版）》请在麦多课文档分享上搜索。

1、ICS 13.220.20; 13.320Ortsfeste Lschanlagen Bauteile fr Sprinkler- undSprhwasseranlagen Teil 3: Trockenalarmventilemit Zubehr (enthlt nderung A1 : 2001)European Standard EN 12259-3 : 2000 + Amendment A1 : 2001 has the status of aDIN Standard.A comma is used as the decimal marker.National forewordThis

2、 standard has been prepared by CEN/TC 191 Fixed firefighting systems.The responsible German body involved in its preparation was the Normenausschuss Feuerwehrwesen (FireFighting Standards Committee), Technical Committee Wasserlschanlagen und deren Bauteile.The DIN Standards corresponding to the Inte

3、rnational Standards referred to in clause 2 of the EN are asfollows:ISO Standard DIN StandardISO 228-1 DIN ISO 228-1ISO 868 DIN ISO 868ISO 898-1 DIN EN 20898-1ISO 898-2 DIN EN 20898-2AmendmentsThis standard differs from the August 2000 edition in that it has been editorially revised and clause 9 dea

4、lingwith the evaluation of conformity and Annex ZA have been included.Previous editionDIN EN 12259-3: 2000-08.National Annex NAStandards referred to(and not included in Normative references and Bibliography)DIN EN 20898-1 Mechanical properties of fasteners Part 1: Bolts, screws and studs (ISO 898-1

5、: 1988)DIN EN 20898-2 Mechanical properties of fasteners Part 2: Nuts with coarse pitch thread and specifiedproof load values (ISO 898-2 : 1992)DIN ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads Part 1:Dimensions, tolerances and designation (ISO 228-1 : 2000)Ref. No.

6、DIN EN 12259-3 : 2001-08English price group 13 Sales No. 111312.01DEUTSCHE NORM August 2001EN 12259-3Continued overleaf.EN comprises 43 pages. No part of this standard may be reproduced without the prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, G

7、ermany,has the exclusive right of sale for German Standards (DIN-Normen).Fixed firefighting systemsComponents for sprinkler and water spray systemsPart 3: Dry alarm valve assemblies(includes Amendment A1 : 2001)English version of DIN EN 12259-3 : 2000 + A1 : 2001SupersedesAugust 2000 edition.English

8、 versionICS 13.220.20; 13.320Descriptors:Fixed firefighting systemsComponents for sprinkler and water spray systemsPart 3: Dry alarm valve assemblies(includes Amendment A1 : 2001) 2001. CEN All rights of exploitation in any form and by any meansreserved worldwide for CEN national members.Ref. No. EN

9、 12259-3 : 2000 + A1 : 2001 EOrtsfeste Lschanlagen Bauteile frSprinkler- und Sprhwasseranlagen Teil 3: Trockenalarmventile mitZubehr(enthlt nderung A1 : 2001)This European Standard was approved by CEN on 1999-12-17 andAmendment A1 on 2001-01-20.CEN members are bound to comply with the CEN/CENELEC In

10、ternal Regulationswhich stipulate the conditions for giving this European Standard the status of anational standard without any alteration.Up-to-date lists and bibliographical references concerning such national stand-ards may be obtained on application to the Management Centre or to anyCEN member.T

11、he European Standards exist in three official versions (English, French, German).A version in any other language made by translation under the responsibility of aCEN member into its own language and notified to the Management Centre hasthe same status as the official versions.CEN members are the nat

12、ional standards bodies of Austria, Belgium, the CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland,and the United Kingdom.EN 12259-3May 2000Management Centre: rue de Stassart 36, B-1050 BrusselsE

13、uropean Committee for StandardizationComit Europen de NormalisationEuropisches Komitee fr Normung|Systmes fixes de lutte contrelincendie Composants dessystmes sprinkleurs et pulvrisation deau Partie 3:Postes dalarme sous air(amendement A1 : 2001 inclus)+A1March 2001SupersedesEN 12259-3 : 2000.Page 2

14、EN 12259-3 : 2000 + A1 : 2001ContentsPageForeword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15、 . . . 42 Normative references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Dry alarm valve assembly construction a

16、nd performance . . . . . . . . . . . . . . . . . 84.1 Nominal size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84.2 Connections to the assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84.3 R

17、ated working pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84.4 Body and cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84.5 Drains . . . . . . . . . . . . . . . . . . . . . . . .

18、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94.6 Sealing assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104.7 Non-metallic elements (excluding gaskets and seals) . . . . . . . . . . . . . . . . . . . . . 114.8

19、Sealing assembly elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114.9 Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124.10 Performance . . . . . . . . . . . . . . . . . . . . .

20、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144.11 Pressure loss due to hydraulic friction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154.12 Leak resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21、154.13 Endurance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Quick opening device construction and performance . . . . . . . . . . . . . . . . . . . . 155.1 Rated working pressure . . . . . . . . . . . . . . . . . . . . . . . . .

22、. . . . . . . . . . . . . . . . . . . . 155.2 Installation pressure leak resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155.3 Body and cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165.4 Connections . .

23、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165.5 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175.6 Non-metallic elements (excluding gaskets and seals) . . . .

24、. . . . . . . . . . . . . . . . . 175.7 Strainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175.8 Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 Marki

25、ng . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196.2 Dry alarm valve . . . . . . . . . . . . . .

26、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196.3 Quick opening device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 Instructions for installation and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27、218 Conditions for testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 Evaluation of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229.1 General . . . . . . . . . . . . . . . . . . . . . . . .

28、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229.2 Initial type testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229.3 Factory production control (FPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

29、. . . . 22Annex A (normative) Fire exposure test for body and cover . . . . . . . . . . . . . . . . 23Annex B (normative) Strength test for body and cover . . . . . . . . . . . . . . . . . . . . 26Annex C (normative) Flow tests for dry alarm valves . . . . . . . . . . . . . . . . . . . . . 26Annex D

30、 (normative) Sealing assembly tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Annex E (normative) Performance tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Annex F (normative) Resistance to ageing test for non-metalliccomponents (excluding gaskets and se

31、als) . . . . . . . . . . . . . . . . . . . . . . . . 37Annex G (normative) Leakage resistance test . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Annex H (normative) Test for sealing assembly elements resistance to adhesion 38Annex I (normative) Endurance test . . . . . . . . . . . . . .

32、. . . . . . . . . . . . . . . . . . . . . 39Annex J (normative) Installation pressure leak resistance test . . . . . . . . . . . . . . 39Annex K (normative) Strength and leak resistance test . . . . . . . . . . . . . . . . . . . . 39Annex L (informative) Typical testing schedule and example of test

33、specimennumbers for dry alarm valve assemblies, accelerators and exhausters . . 40Annex ZA (informative) Clauses of this European Standard addressing theprovisions of the EU Construction Products Directive . . . . . . . . . . . . . . 41Bibliography . . . . . . . . . . . . . . . . . . . . . . . . . .

34、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Page 3EN 12259-3 : 2000 + A1 : 2001ForewordThis European Standard has been prepared by Technical Committee CEN/TC 191 Fixed firefightingsystems, the Secretariat of which is held by BSI.This European Standard has been prepared under a

35、 mandate given to CEN by the European Commissionand the European Free Trade Association, and supports essential requirements of the relevant EUDirective.For relationship with this directive, see Annex ZA.This European Standard shall be given the status of a national standard, either by publication o

36、f anidentical text or by endorsement, by September 2001 at the latest, and conflicting national standards shallbe withdrawn by December 2001 at the latest.In accordance with the CEN/CENELEC Internal Regulations, the national standards organizations of thefollowing countries are bound to implement th

37、is European Standard:Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland,Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the UnitedKingdom.This standard forms one Part of EN 12259 covering components for automatic sp

38、rinkler systems and isincluded in a series of European Standards planned to cover: automatic sprinkler systems (EN 12259 and EN 12845); gaseous extinguishing systems (EN 12094); powder systems (EN 12416); explosion protection systems (EN 26184); foam systems (EN 13565); hose reel systems (EN 671); s

39、moke and heat control systems (EN 12101); water spray systems.EN 12259 has the general title Fixed firefighting systems Components for sprinkler and water spraysystems and will comprise:Part 1 SprinklersPart 2 Wet alarm valve assembliesPart 3 Dry alarm valve assembliesPart 4 Water motor alarmsPart 5

40、 Water flow detectorsPart 6 Pipe couplingsPart 7 Pipe hangersPart 8 Pressure switchesPart 9 Deluge alarm valve assembliesPart 10 Multiple controlsPart 11 Medium and high velocity water sprayersPart 12 Sprinkler pump setsPage 4EN 12259-3 : 2000 + A1 : 2001Page 5EN 12259-3 : 2000 + A1 : 2001Page 6EN 1

41、2259-3 : 2000 + A1 : 2001Page 7EN 12259-3 : 2000 + A1 : 2001Page 8EN 12259-3 : 2000 + A1 : 2001Page 9EN 12259-3 : 2000 + A1 : 2001Page 10EN 12259-3 : 2000 + A1 : 2001Page 11EN 12259-3 : 2000 + A1 : 2001Page 12EN 12259-3 : 2000 + A1 : 2001Page 13EN 12259-3 : 2000 + A1 : 2001Page 14EN 12259-3 : 2000 +

42、 A1 : 2001Page 15EN 12259-3 : 2000 + A1 : 2001Page 16EN 12259-3 : 2000 + A1 : 2001Page 17EN 12259-3 : 2000 + A1 : 2001Page 18EN 12259-3 : 2000 + A1 : 2001Page 19EN 12259-3 : 2000 + A1 : 2001Page 20EN 12259-3 : 2000 + A1 : 2001Page 21EN 12259-3 : 2000 + A1 : 2001Page 22EN 12259-3 : 2000 + A1 : 20019

43、Evaluation of conformity9.1 GeneralThe compliance of a wet alarm valve assembly with the requirements of this standard shall bedemonstrated by: initial type testing; factory production control by the manufacturer.9.2 Initial type testingInitial type testing shall be performed on first application of

44、 this standard. Tests previously performed inaccordance with the provisions of this standard (product, characteristic, test method, sampling method andsystem of attestation of conformity etc.) may be taken into account. In addition, initial type testing shallbe performed at the beginning of the prod

45、uction of a product type or at the beginning of a new method ofproduction (where these may affect the stated properties).All characteristics given in clause 4, and where appropriate clause 5, shall be subject to initial type testing.9.3 Factory production control (FPC)The supplier shall establish, d

46、ocument and maintain an FPC system to ensure that the products placed onthe market conform with the stated performance characteristics.The FPC system shall consist of procedures, regular inspections and tests and/or assessments and the useof the results to control raw and other incoming materials or

47、 components, equipment, the productionprocess and the product. It shall be sufficiently detailed to ensure that the conformity of the product isapparent, ensuring detection of irregularities at the earliest possible stage.An FPC system conforming with the requirements of the relevant part(s) of EN I

48、SO 9000, and madespecific to the requirements of this standard, shall be considered to satisfy the above requirements.The results of inspections, tests or assessments requiring action shall be recorded, as shall any actiontaken. The action to be taken when control values or criteria are not met shal

49、l be recorded.The production control procedure shall be recorded in a manual, which shall be made available whenrequested.The supplier shall carry out and record the results of production tests as part of the production control.These records shall be available if requested.Leakage resistance, alarm and sensitivity characteristic tests, shall be carried out on each dry alarm valveassembly.Page 23EN 12259-3 : 2000 + A1 : 2001Page 24EN 12259-3 : 2000 + A1 : 2001Page 25EN 12259-3 : 2000 + A1 : 2001Page 26EN 12259-3 : 2000 + A1 : 2