DIN EN 12020-1-2008 Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1 Technical conditions for inspection and delivery Engli.pdf

《DIN EN 12020-1-2008 Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1 Technical conditions for inspection and delivery Engli.pdf》由会员分享，可在线阅读，更多相关《DIN EN 12020-1-2008 Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1 Technical conditions for inspection and delivery Engli.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、June 2008DEUTSCHE NORM English price group 9No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 77.150.10!$O+Z“1440855www.

2、din.deDDIN EN 12020-1Aluminium and aluminium alloys Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 Part 1: Technical conditions for inspection and deliveryEnglish version of DIN EN 12020-1:2008-06Aluminium und Aluminiumlegierungen Stranggepresste Przisionsprofile aus Legierungen EN

3、AW-6060 und EN AW-6063 Teil 1: Technische LieferbedingungenEnglische Fassung DIN EN 12020-1:2008-06SupersedesDIN EN 12020-1:2001-07www.beuth.deDocument comprises 13 pagesDIN EN 12020-1:2008-06 2 National foreword This standard has been prepared by Technical Committee CEN/TC 132 “Aluminium and alumin

4、ium alloys” (Secretariat: AFNOR, France), Working Group WG 5 “Extruded and drawn products” (Secretariat: SN, Norway). The responsible German body involved in its preparation was the Normenausschuss Nichteisenmetalle (Nonferrous Metals Standards Committee), Technical Committee NA 066-01-04 AA Strangp

5、resserzeugnisse. Amendments This standard differs from DIN EN 12020-1:2001-07 as follows: a) The definition of “order document” has been included in clause 3. b) An additional Figure 3 has been included in subclause 4.2 identifying visible surfaces and weld lines. c) Requirements relating to streaks

6、 and surface texture appearance on visible surfaces in mill finish have been included in subclause 5.5. d) Requirements relating to tolerance on mass have been included in subclause 5.7. e) The standard has been editorially revised. Previous editions DIN 17615: 1976-12, 1987-01 DIN EN 12020-1: 2001-

7、07 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12020-1 March 2008 ICS 77.150.10 Supersedes EN 12020-1:2001 English Version Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery Aluminium et

8、 alliages daluminium - Profils de prcision fils en alliages EN AW-6060 et EN AW-6063 - Partie 1: Conditions techniques de contrle et de livraison Aluminium und Aluminiumlegierungen - Stranggepresste Przisionsprofile aus Legierungen EN AW-6060 und EN AW-6063 - Teil 1: Technische Lieferbedingungen Thi

9、s European Standard was approved by CEN on 10 February 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refer

10、ences concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member

11、into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latv

12、ia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brus

13、sels 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12020-1:2008: EEN 12020-1:2008 (E) 2 Contents Page Foreword . 3 1 Scope 4 2 Normative references 5 3 Terms and definitions. 5 4 Ordering information 6 4.1 General . 6 4.2 Re

14、ference to a drawing. 7 5 Requirements 7 5.1 Production and manufacturing processes.7 5.2 Quality control . 8 5.3 Chemical composition limit . 8 5.4 Mechanical properties 8 5.5 Freedom from surface defects. 8 5.6 Tolerances on dimensions and form 8 5.7 Section mass . 8 6 Test procedures 8 6.1 Sampli

15、ng 8 6.2 Test methods . 9 7 Inspection documents 9 8 Marking of products 9 9 Packaging 10 10 Arbitration 10 Bibliography 11 DIN EN 12020-1:2008-06 EN 12020-1:2008 (E) 3 Foreword This document (EN 12020-1:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the

16、secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdrawn at the latest by September 2008. This d

17、ocument supersedes EN 12020-1:2001. Within its programme of work, Technical committee CEN/TC 132 entrusted CEN/TC 132/WG 5 “Extruded and drawn products“ to revise EN 12020-1:2001 The following technical modifications have been introduced during the revision: Clause 3: Definition of “order document“

18、is included Subclause 4.2: An additional Figure 3 is included identifying visible surfaces and weld lines Subclause 5.5: Requirements to streaks and surface texture appearance on visible surfaces in mill finish are included Subclause 5.7: Requirements to tolerance on mass are included EN 12020 compr

19、ises the following parts under the general title “Aluminium and aluminium alloys Extruded precision profiles in alloys EN AW-6060 and EN AW-6063“: Part 1: Technical conditions for inspection and delivery Part 2: Tolerances on dimensions and form Attention is drawn to the possibility that some of the

20、 elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardized standards products under reas

21、onable and not discriminatory conditions then this product shall be removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, C

22、yprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 12020-1:2008-06 EN 12020-1:

23、2008 (E) 4 1 Scope This document specifies technical conditions for inspection and delivery of alloys EN AW-6060 and EN AW-6063 extruded precision profiles manufactured with and without a thermal barrier (see Figures 1 and 2) and without further surface treatment. Precision profiles covered in this

24、document are distinguished from extruded profiles for general applications covered in EN 755-9 by the following characteristics: they are mainly for architectural applications; they meet more stringent requirements regarding the surface condition of visible surfaces; the maximum diameter of the circ

25、umscribing circle CD is 350 mm; they are made to closer tolerances on dimensions and form. In the case of profiles, which, due to the complexity of their design are difficult to manufacture and specify, then special agreements between supplier and purchaser may need to be reached. NOTE The effect of

26、 the thermal barrier material on the dimensional tolerances is covered by EN 12020-2 although the actual thermal barrier material itself is not (see EN 14024). Key 1 CD maximum 350 mm Key 1 CD maximum 350 mm 2 thermal barriers Figure 1 Profile without thermal barrier Figure 2 Profile containing ther

27、mal barrier DIN EN 12020-1:2008-06 EN 12020-1:2008 (E) 5 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references only the edition cited applies. For undated references the latest edition of the referenced document (includ

28、ing any amendments) applies. EN 515, Aluminium and aluminium alloys Wrought products Temper designations EN 573-3, Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products EN 755-1, Aluminium and aluminium alloys Extruded

29、rod/bar, tube and profiles Part 1: Technical conditions for inspection and delivery EN 755-2, Aluminium and aluminium alloys Extruded rod/bar, tube and profiles Part 2: Mechanical properties EN 10002-1, Metallic materials Tensile testing Part 1: Method of test at ambient temperature EN 10204, Metall

30、ic products Types of inspection documents EN 12020-2, Aluminium and aluminium alloys Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 Part 2: Tolerances on dimensions and form EN 12206-1, Paints and varnishes Coating of aluminium and aluminium alloys for architectural purposes Part 1:

31、 Coatings prepared from coating powder EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitions Part 1: General terms EN 12373-1, Aluminium and aluminium alloys Anodizing Part 1: Method for specifying decorative and protective anodic oxidation coatings on aluminium EN 14242, Aluminium a

32、nd aluminium alloys Chemical analysis Inductively coupled plasma optical emission spectral analysis EN 14361, Aluminium and Aluminium alloys Chemical analysis Sampling from metal melts EN ISO 4287, Geometrical product specifications (GPS) Surface texture: Profile method Terms, definitions and surfac

33、e texture parameters (ISO 4287:1997) EN ISO 4288, Geometrical product specifications (GPS) Surface texture: Profile method Rules and procedures for the assessment of surface texture (ISO 4288:1996) EN ISO 6506-1, Metallic materials Brinell hardness test Part 1: Test method (ISO 6506-1:2005) 3 Terms

34、and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following apply. 3.1 order document document or set of documents agreed between supplier and purchaser at the time of ordering DIN EN 12020-1:2008-06 EN 12020-1:2008 (E) 6 4 Ordering informa

35、tion 4.1 General The order document shall contain the following: a) the designation of the aluminium alloy (EN AW-6060 or EN AW-6063); b) the temper of the material for delivery in accordance with EN 755-2 (The temper designations to be used are according to EN 515); c) the application, in particula

36、r, when surface treatment is intended; this shall be expressly stated on the order document; d) reference to this document (EN 12020-1); e) reference to a drawing defining the product (see 4.2), cross sectional dimensions, mass per meter calculated on nominal section dimensions, surface requirements

37、 and any other relevant information; f) length: fixed or random, for random lengths minimum and maximum shall be specified, an allowance for process contact points of surface treatment may be necessary; g) quantity: mass or number of pieces or total length, tolerance on quantity; h) special requirem

38、ents: any special requirements agreed between the supplier and purchaser, agreement on plane parallelism, any requirement for inspection documents, marking of products, reference to other standards, if tolerances on dimensions and form differ from those specified in EN 12020-2, additional or special

39、 testing, installation length, surface protection; i) packaging information: pack mass/size. DIN EN 12020-1:2008-06 EN 12020-1:2008 (E) 7 4.2 Reference to a drawing On the basis of the order document, the manufacturer shall prepare drawings, which are to be checked by the purchaser for accuracy, and

40、 approved, the profiles then being manufactured in strict accordance with the approved drawing. If for dimensions critical to function, tolerances other than those specified in this document are to be used, they shall be entered in the drawing adjacent to the associated nominal size. This also appli

41、es to the tolerances on form. Where profiles are intended for later assembly, it is recommended that the manufacturer is provided with a drawing giving appropriate details. Where for manufacturing reasons weld lines are to be located on visible surfaces their position or approximate area of appearan

42、ce should be indicated by the manufacturer on the drawing. Visible surfaces shall be identified, indicating main and, if necessary, secondary order visible surfaces. Key 1 visible surface 2 area of probable appearance of weld lines 3 area of probable appearance of T-joint streaks Figure 3 Marking of

43、 visible surfaces of approximate area of appearance of weld lines and T-joint streaks For profiles intended for surface treatment, surfaces and areas that are to be so treated should be indicated on the drawing. If the outline of a profile is modified by machining, it is recommended that the final s

44、hape is also indicated. 5 Requirements 5.1 Production and manufacturing processes Unless otherwise specified in the order document, the production and manufacturing processes shall be left to the discretion of the manufacturer. Unless it is explicitly stated in the order document, no obligation shal

45、l be placed on the manufacturer to use the same processes for subsequent or similar orders. DIN EN 12020-1:2008-06 EN 12020-1:2008 (E) 8 5.2 Quality control The supplier shall be responsible for the performance of all inspection and tests required by the relevant European Standard and/or the particu

46、lar specification prior to shipment of the product. If the purchaser wishes to inspect the product at the manufacturers works, he shall notify the supplier at the time of placing the order. 5.3 Chemical composition limit The chemical composition limit shall be in conformity with the requirements spe

47、cified in EN 573-3. If the purchaser requires closer limits for elements than those specified in the above standard, these limits shall be according to an agreement between supplier and purchaser and stated in the order document. 5.4 Mechanical properties The mechanical properties shall comply with

48、the requirements of EN 755-2 or those agreed between supplier and purchaser and stated in the order document. Hardness testing may be used for release purposes subject to agreement between supplier and purchaser. 5.5 Freedom from surface defects The extruded visible surface shall be free from defect

49、s prejudicial to its suitable and proper use. Slight scoring and other minor defects are permissible providing that values of Rz of 9 m or Ra of 2 m are not exceeded when determined according to EN ISO 4287 and EN ISO 4288. Any discoloration or minor blemishes that are likely to be eliminated by the intended pretreatment for anodizing according to EN 12373-1 or by painting according to EN 12206-1 shall be permitted. Requirements on streaks and surface textu