DIN EN 10056-2-1994 Structural steel equal and unequal leg angles part 2 tolerances on shape and dimensions German version EN 10056-2 1993《等边和不等边角钢 第2部分 形状和尺寸公差》.pdf

《DIN EN 10056-2-1994 Structural steel equal and unequal leg angles part 2 tolerances on shape and dimensions German version EN 10056-2 1993《等边和不等边角钢 第2部分 形状和尺寸公差》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 10056-2-1994 Structural steel equal and unequal leg angles part 2 tolerances on shape and dimensions German version EN 10056-2 1993《等边和不等边角钢 第2部分 形状和尺寸公差》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、DC 669.14.018.29-423.1 :621.713.1 DEUTSCHE NORM March 1994 I Structural steel equal and unequal leg angles I DIN - I EN10056 Tolerances on shape and dimensions English version of DIN EN 10056 Part 2 Part 2 Gleichschenklige und ungleichschenklige Winkel aus Stahl; Grenzabmae und Formtoleranzen This s

2、tandard, together with the March 1994 editions of DIN 1028 and DIN 1029, supersedes the October 1976 edition of DIN 1028 and the July 1978 edition of DIN 1029. European Standard EN 10056-2:1993 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard h

3、as been prepared by ECISS/TC 11. The responsible German body involved in its preparation was the Normenausschu Eisen und Stahl (Steel and Iron Standards Committee), Technical Committee Warmgewalzte Profilerzeugnisse. The specifications made in the present standard had previously been covered separat

4、ely, in DIN 1028 and DIN 1029. The form of this standard differs from that commonly used in Germany. The requirements for both nominal size and the relevant tolerances had been split up into the two DIN Standards, one covering equal and the other, unequal angles, but here, only the latter are specif

5、ied in this one product standard, although they apply to both products. Specifications regarding the nominal size ranges for equal and unequal angles are currently in preparation, and will be published in Part 1 of this European Standard (cf. clause 1). The DIN Standards corresponding to the Europea

6、n Standard and EURONORMs referred to in clause 2 of the EN are as follows: EN Standard DIN Standard EN 10079 DIN EN 10079 EURONORM 56 DIN 1028 EURONORM 57 DIN 1029 Standards referred to (and not included in Normative references) DIN EN 10079 Definition of steel products DIN 1028 Hot rolled equal ang

7、les with rounded toes: dimensions, mass and static parameters DIN 1029 Hot rolled unequal angles with rounded toes; dimensions, mass and static parameters Previous editions DIN 1612: 09.24,01.32, 03.43; DIN 1028 Part 1 : 07.26,07.40; DIN 1028 Part 2: 07.26, 07.40; DIN 1028: 07.59, 10.63, 10.76: DIN

8、1029 Part 1: 10.26, 12.36, 07.40; DIN 1029 Part 2: 10.26, 01.39, 07.40; DIN 1029: 07.59, 10.63, 07.78. Amendments In comparison with the October 1976 edition of DIN 1028 and the July 1978 edition of DIN 1029, the following amendments have been made. a) Nominal size ranges and static values are no lo

9、nger specified. b) Some of the tolerances specified for thickness have been amended (cf. table 1). c) The tolerance on mass is closer. EN comprises 3 pages. Beuth Verlag GmbH, Berlin, has the exclusive right of sale for German Standards (DIN-Normen). DIN EN 10 056 fart 2 Engl. Price group 5 07.94 Sa

10、les No. 1105 EUROPEAN CTANDARD NORME EUROPENNE EUROPAISCHE NORM EN 10056-2 September 1993 UDC 669.14.018.29-423.1 621.713.1 Descriptors: Iron and steel products, angle irons, structural steels, dimensional tolerances, form tolerances. English version Structural steel equal and unequal leg angles Tol

11、erances on shape and dimensions Cornires ailes gales et ailes ingales en acier de construction; tolrances de formes et de dimensions Gleichschenklige und ungleich- schenklige Winkel aus Stahl; Grenzabmae und Formtoleranzen This European Standard was approved by CEN on 1993-08-30. CEN members are bou

12、nd to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the C

13、entral Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). Aversion in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status a

14、s the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit E

15、uropen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, 8-1050 Brussels O 1993. Copyright reserved to all CEN members. Ref. No. EN 10056-2:1993 E Page 2 EN 10056-2:1993 Contents list Page Page Foreword 2 5 Tolerance on mass 2 6 Tolerance on length . 2 1 Scope

16、2 Table 1: Tolerances on dimensions, squareness and 2 Normative references . 2 straightness of structural steel equal and 3 Definitions 2 unequal leg angles . 3 4 Tolerances on shape and dimensions . 2 Annex A (informative) Straightness measurement 3 Foreword This European Standard has been prepared

17、 by ECISS/TC 11 Sections: Tolerances and dimensions, the Secretariat of which is held by BSI. The discussions within ECISS/TC 11 were based on EURONORM 56-77 Hot rolled equal angles (with radiused root and toes) and EURONORM 57-78 Hot rolled unequal angles (with radiused root and toes) This European

18、 Standard shall be given the status of a national standard, either by publication of an identical text or by en- dorsement, and conflicting national standards withdrawn, by March 1994 at the latest. In accordance with the CENKENELEC Internal Regulations, the following countries are bound to implemen

19、t this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 1 Scope This Part of this European Standard specifies tolerances on the shape, dimensions and

20、mass of hot rolled structural steel equal and unequal leg angles. The sizes of these angles are given in EN 10056-1. These tolerances do not apply to stainless steel equal and unequal leg angles. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions fr

21、om other publications. These nor- mative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amen

22、dment or revision. For undated references, the latest edition of the publication referred to applies. EN 10056-1 EN 1 O 079 EURONORM 56-77 EURONORM 57-78 (at present at the stage of draft) Structural steel equal and unequal leg angles. Part 1 : Nominal size ranges Definition of steel products Hot ro

23、lled equal angles (with radi- used root and toes) Hot rolled unequal angles (with radi- used root and toes) 3 Definitions For the purposes of this European Standard, the definitions given in EN 10079 apply. 4 Tolerances on shape and dimensions 4.1 The nominal leg length shall be wjthin the tolerance

24、s gjven in table 1. Leg length (a or b) For unequal leg angles, the longer leg length, a, shall be used. 4.2 Section thickness (t) The nominal section thickness shall be within the toler- ances given in table 1. 4.3 Out-of-squareness (k) The out-of-squareness of the section shall not exceed the valu

25、es specified in table 1. For unequal leg angles, the longer leg length, a, shall be used. 4.4 Deviation from straightness (4) The deviation from straightness shall not exceed the values specified in table 1. For unequal leg angles, the longer leg length, a, shall be used. 5 Tolerance on mass The dev

26、iation from the nominal mass of any angle shall not exceed C6% for thicknesses, t, not exceeding 4 mm, or f 4 % for thicknesses, t, over 4 mm. The deviation from the nominal mass is the difference between the actual mass of the angle and the calculated mass. The calculated mass shall be determined u

27、sing a density of 7,85 kg/drn3. 6 Tolerance on length The tolerance on ordered length shall be it 50 mm, or +to mm where minimum lengths are required. Page 3 EN 1 O 056-2 : 1993 100 15 f 120 Dimensions Squarenesc U Straightness Leg length, a Section thickness, t Tolerance on Nominal size a and b Nom

28、inal size Tolerance mm I Out-of-squareness, k Leg length, a a I 100 100 200 3,O Tolerance on straightness, q Leg length, e mm ai 150 Tolerance over any length Tolerance over Relevant full leg length, Leg length, a length 0.4% of L 1500 a 200 3000 4 mm 6 3 - - 3 Annex A (informative) Straightness mea

29、surement Straightness measurement requires the use of a straight edge from which deviations in section straightness are measured. A taut string line is an acceptable straight edge, provided that deviations in the horizontal plane only are measured. Measurement shall be carried out as follows: The angle is placed on one leg on a flat surface, and the string is taken from the flat surface to the toe of the other (unconstrained) leg. The width of the gap between the string and the unconstrained leg shall be measured.