DIN EN 10051-2011 Continuously hot-rolled strip and plate sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape German version EN 10051 2010《.pdf
《DIN EN 10051-2011 Continuously hot-rolled strip and plate sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape German version EN 10051 2010《.pdf》由会员分享,可在线阅读,更多相关《DIN EN 10051-2011 Continuously hot-rolled strip and plate sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape German version EN 10051 2010《.pdf(18页珍藏版)》请在麦多课文档分享上搜索。
1、February 2011 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I
2、CS 77.140.50!$mr+“1747908www.din.deDDIN EN 10051Continuously hot-rolled strip and plate/sheet cut from wide strip ofnon-alloy and alloy steels Tolerances on dimensions and shapeEnglish translation of DIN EN 10051:2011-02Kontinuierlich warmgewalztes Band und Blech abgelngt aus Warmbreitband ausunlegi
3、erten und legierten Sthlen Grenzabmae und FormtoleranzenEnglische bersetzung von DIN EN 10051:2011-02Bandes lamines chaud en continu, bandes et tles issues de larges bandes lamines chaud en aciers allis et non allis Tolrances sur les dimensions et la formeTraduction anglaise de DIN EN 10051:2011-02T
4、ogether with supersedesDIN EN 10051:1997-11www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.DIN EN ISO 9444-2:2010-11,1802.11 DIN EN 10051:2011-02 2 A comma is used as the decimal marker. National foreword This standard has been pre
5、pared by Technical Committee ECISS/TC 103 “Structural steels other than reinforcements” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Eisen und Stahl (Steel and Iron Standards Committee), Subcommittee 20/1 Manormen fr warmgewalzte Flache
6、rzeugnisse. Amendments This standard differs from DIN EN 10051:1997-11 as follows: a) stainless steel plates have been deleted from the scope of this standard, they are now covered by EN ISO 9444-2:2010; b) Clause 2 “Normative references” has been updated; c) in Clause 3 “Terms and definitions”, 3.3
7、 crown has been added; d) Subclauses 4.1 “General” and 4.2 “Options” have been modified; e) in Table 2 “Tolerances on thickness”, nominal thicknesses 8,00 mm t 11,00 mm have been included; f) the “tolerances on thickness” are now classified according to the minimum yield strength (categories A, B, C
8、 and D) Tables 3 to 6; g) the “tolerances on flatness” are now classified according to the minimum yield strength (categories A, B, C and D) Tables 9 and 10; h) the definition of the length of sheet/plate (8.3) has been modified; i) a new Figure 1 relating to the edge camber has been added; j) Annex
9、es A and B have been modified; k) the standard has been editorially revised. Previous editions DIN 1541-1: 1932-05 DIN 1541-2: 1932-05 DIN 1016: 1941x-10, 1959-01, 1972-11, 1987-06 DIN EN 10051: 1992-02, 1997-11 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10051 November 2010 ICS 77.140.50 S
10、upersedes EN 10051:1991 + A1:1997English Version Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape Bandes lamines chaud en continu, bandes et tles issues de larges bandes lamines chaud en aciers allis et non allis - T
11、olrances sur les dimensions et la forme Kontinuierlich warmgewalztes Band und Blech abgelngt aus Warmbreitband aus unlegierten und legierten Sthlen -Grenzabmae und Formtoleranzen This European Standard was approved by CEN on 23 October 2010. CEN members are bound to comply with the CEN/CENELEC Inter
12、nal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN memb
13、er. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN membe
14、rs are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
15、Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membe
16、rs. Ref. No. EN 10051:2010: EEN 10051:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Information to be supplied by the purchaser .54.1 General 54.2 Options .54.3 Designation 55 Form of supply .56 Tolerances for sheet/plate 66.1 Thickness .66.2 Length
17、.86.3 Width .86.4 Flatness 96.5 Edge camber . 106.6 Out-of-squareness 106.7 Superimposement of dimensions . 107 Tolerances for wide strip and strip split from wide strip . 107.1 General . 107.2 Thickness 107.3 Width 117.4 Flatness . 117.5 Edge camber . 128 Measurement . 128.1 General . 128.2 Thickne
18、ss 128.3 Length of sheet/plate 128.4 Width 128.5 Flatness for sheet/plate 128.6 Edge camber . 128.7 Out-of-squareness for sheet/plate 13Annex A (informative) Standards with steel grades for this dimensional standard . 14Annex B (normative) Options . 16DIN EN 10051:2011-02 EN 10051:2010 (E) 3 Forewor
19、d This document (EN 10051:2010) has been prepared by Technical Committee ECISS/TC 103 “Structural steels other than reinforcements”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endo
20、rsement, at the latest by May 2011, and conflicting national standards shall be withdrawn at the latest by May 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying
21、any or all such patent rights. This document supersedes EN 10051:1991+A1:1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic
22、, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 10051:2011-02 EN 10051:2010 (E) 4 1 Scope This E
23、uropean Standard specifies tolerances on dimensions and shape for continuously hot-rolled uncoated plate/sheet and strip with a maximum width of 2 200 mm of non-alloy and alloy steels in accordance with Table 1 (see also Annex A). This European Standard also applies to hot-rolled strip for cold roll
24、ing. Table 1 Field of application Product Thickness mm Steel grades according to: (but not limited to) wide strip (width: 600 mm w 2 200 mm), Sheet/Plate cut from wide strip, strip w 10 mm (see 6.3); h) tolerances on flatness for sheet/plate of category D (see 6.4.2 and Table 10); i) edge camber req
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DINEN100512011CONTINUOUSLYHOTROLLEDSTRIPANDPLATESHEETCUTFROMWIDESTRIPOFNONALLOYANDALLOYSTEELSTOLERANCESONDIMENSIONSANDSHAPEGERMANVERSIONEN100512010PDF

链接地址:http://www.mydoc123.com/p-663632.html