DIN EN 10048-1996 Hot-rolled narrow steel strip - Tolerances on dimensions and shape German version EN 10048 1996《热轧钢窄带材 尺寸和外形公差 德文版本 EN 10048 1996》.pdf

《DIN EN 10048-1996 Hot-rolled narrow steel strip - Tolerances on dimensions and shape German version EN 10048 1996《热轧钢窄带材 尺寸和外形公差 德文版本 EN 10048 1996》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 10048-1996 Hot-rolled narrow steel strip - Tolerances on dimensions and shape German version EN 10048 1996《热轧钢窄带材 尺寸和外形公差 德文版本 EN 10048 1996》.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、DEUTSCHE NORM October 1996 Hot rolled narrow steel strip Dimensional and geometrical tolerances English version of DIN EN 10048 EN 10048 ICs 77.1 40.50 Descriptors: Steel, strip, tolerances. Warmgewalzter Bandstahl - Grenzabmae und Formtoleranzen This standard, together with DIN EN 10051, February 1

2、992 edition, supersedes DIN 1016. June 1987 edition. European Standard EN 10048:1996 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been prepared by ECISSTTC 13. The responsible German body involved in the preparation of this standard was

3、 the Normenausschu Eisen und Stahl(Stee1 and Iron Standards Committee), Technical Committee 20/1 Manormen fr warmgewalzte Flacherzeugnisse. The DIN Standards corresponding to the EURONORMs referred to in clause 2 of the EN are as follows: EURONORM DIN Standard EU 85-70 DIN 1721 1 EU 86-70 DIN 17212

4、EU 89-71 DIN 17221 EU 96-79 DIN 17350 EU 132-79 DIN 17222 Amendments In comparison with DIN 1016, June 1987 edition, the following amendments have been made. a) The scope of the standard has been restricted to cover only strip less than 600 mm in nominal width. b) Closer tolerances on thickness have

5、 been specified. c) Smaller increments have been specified for thickness tolerances for steel exhibiting a high deformation resistance at elevated temperature (cf. tables 3 and 4). d) Closer tolerances on width for strip with slit edges have been specified. Previous editions DIN 1541-1: 1932-5; DIN

6、1541-2: 1932-05; DIN 1016: 1941-10, 1959-01, 1972-11, 1987-06. Continued overleaf. EN comprises 23 pages. No part of this standard may be reproduced without the prior permission of i/ Deutsches Institut fr Normung e.V., Berlin. uth Verlag GmbH, Berlin, has theexclusive right of sale for German Stand

7、ards(D1N-Normen) Ref. No. DIN EN 70048:1996-10 Price group i 1 Sales No. 17 11 05.97 COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 2 DIN EN 10048:1996-10 Standards referred to (and not included in Normative references) DIN 17210 DIN 1721 1 DI

8、N 17212 DIN 17221 DIN 17222 DIN 17350 DIN EN 10051 Case hardening steel - Technical delivery conditions Nitriding steels - Technical delivery conditions Steel for flame and induction hardening - Technical delivery conditions Hot rolled steel for springs suitable for quenching and tempering - Technic

9、al delivery conditions Cold rolled steel strip for springs - Technical delivery conditions Tool steel - Technical delivery conditions Continuously hot rolled uncoated unalloyed and alloy steel plate, sheet and strip - Dimensional and geometrical toler- ances COPYRIGHT DIN DEUTSCHES Institut Fur Norm

10、ung E.V.- EnglishLicensed by Information Handling ServicesEUROPEAN STAN DAR D NORME EUROPENNE EUROPISCHE NORM EN 10048 August 1996 ICs 77.140.50 Descriptors: Steel, strip, tolerances. English version Hot rolled narrow steel strip Tolerances on dimensions and shape Feuillards lamines chaud - Tolrance

11、s de dimensions et de forme und Formtoleranzen Warmgewalzter Bandstahl - Grenzabmae This European Standard was approved by GEN on 1995-10-04. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nati

12、onal standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in an

13、y other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Icel

14、and, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 1996. CEN - All righ

15、ts of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN 10048: 1996 E COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 2 EN 10048 : 1996 Page Contents 3 Foreword 3 1 Scope 3 2 Normative references

16、 5 3 Definitions 6 4 Forms and condition of delivery 6 6 4.1 Forms of delivery 4.2 Condition of delivery 6 5 Information to be supplied by the purchaser 7 6 Designation 7 7 Tolerances on dimensions 7 11 12 7.1 Thickness and tolerances on crown 7.2 Tolerances on width 7.3 Tolerances on cut lengths 13

17、 8 Tolerances on shape 13 13 14 8.1 Straightness of edges (edgewise) 8.2 Form of coils 8.3 Tolerances on squareness 14 9 Measurements 14 14 14 9.1 Thickness 9.2 Width 9.3 Squareness of edges 15 10 Packing 15 11 Options 16 Annexes 16 A (informative) : List of corresponding national designations, stan

18、dards or specifications for categories B, C and D of table 4 B (informative) : List of national standards corresponding to the EURONORMS referred to (see clause 2) 23 COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 3 EN 10048 : 1996 Foreword Th

19、is European Standard has been prepared by Technical Committee ECISS/TC 13 “Flat products for cold working - Qualities, dimensions, tolerances and specific tests“ the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of

20、 an identical text or by endorsement, at the latest by February 1997, and conflicting national standards shall be withdrawn at the latest by February 1997. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Eu

21、ropean Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 1 Scope 1.1 This European Standard applies to uncoated hot rolled narrow steel strip, of width less tha

22、n 600 mm, made of the steel grades covered by the following: EURONORMS 85, 86, 89, 96, 132; European Standards EN 10025, EN 10028-2, EN 10028-3, EN 10083-1, EN 10083-2, 10149-2, EN 10149-3, EN 10155, EN 10207 and EN 10208-2; EN 10083-3, EN 10088-2, EN 10113-2, EN 10113-3, EN 10137-2, EN 10137-3, EN

23、draft European Standards prEN 10028-5, prEN 10028-6 and prEN 10084. NOTE: This European Standard may be applied to other types of steels if agreed at the time of ordering. 1.2 This European Standard does not apply to hot roiled wide strip and narrow strip (width 4 and 5 8 mm, 0,20 mm for nominal thi

24、cknesses 8 mm. COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 9 EN 10048 : 1996 Nominal width of the narrow strip W, 3,O I 5,O O/+ 0,7 O/+ 0,7 O/+ 0,8 O/+ 0,8 I 7,O I 10,o 10,o by agreement ) Symmetrical plus and minus values for the tolerance

25、 on width may be agreed at the time of ordering (e.g. : f 0,4 mm instead of O+ 0,8 mm). However, the total tolerance range shall correspond to the values given in the table. Option 4. Tighter tolerances may be the subject of special agreements at the time of ordering. Option 5. 7.2.2 Width tolerance

26、s for narrow steel strip exhibiting a high deformation resistance at elevated temperatures. 7.2.3 Variations in width shall be gradual and shall not occur irregularly 7.3 Tolerances on cut lengths 7.3.1 Lengths cut from narrow strip are normally delivered in fixed lengths between lo00 and 12000 mm,

27、with the tolerances given in table 7. The type of tolerance selected shall be specified at the time of ordering. Option 6. Short lengths may be supplied as long as this has not been expressly excluded under the terms of the order and the lengths supplied do not fall below 50 % of the nominal lengths

28、. COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 13 EN 10048 : 1996 Type of tolerances Normal tolerances Fine tolerances Table 7 : Tolerances on length Dimensions in millimetres Tolerances on length ) + 50 O + (0,005 x L + 10) but max. 502) O

29、8 Tolerances on shape 8.1 Straightness of edges (edgewise bow) 8.1.1 For products of thickness 2 mm, the tolerance on straightness of edges shall be agreed at the time of ordering. 8.1.2 For products of thickness 2 2 mm, the tolerance on straightness of edges relative to a length of 2500 mm shall be

30、 as follows: 20 mm for products of width 40 mm 10 mm for products of width 2 40 mm and 600 mm. 8.1.3 For lengths other than 2500 mm, the tolerance on straightness shall be calculated on the basis of the following formula with the result being rounded to the next highest millimetre: 2 x (tolerance on

31、 straightness - lm! gradually stepped displacement of the edge of the strip to one side shall not exceed 35 mm. COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 14 EN 10048 : 1996 8.3 Tolerances on squareness The out-of-squareness of lengths sha

32、ll not exceed 1 % of the nominal width or fraction thereof. 9 Measurements 9.1 Thickness 9.1.1 For products of width up to 30 mm, the thickness is measured at any point on the longitudinal axis. For products of width greater than 30 mm, it is measured at any point at least 10 or 15 mm from the longi

33、tudinal edges depending on whether they are slit or as-roiled edges. 9.1.2 The measurements shall be taken at least 3000 mm from the ends of coils with end tongues and at least 2000 mm for coils without end tongues. 9.1.3 The measuring points for determining the camber (see 7.1.1.5) shall be on a li

34、ne running perpendicular to the longitudinal axis of the product, 9.1.4 The variation in thickness over a coil (see 7.1.1.3) shall be measured on a line running parallel to the edge of the narrow strip at least 15 mm from it. The requirements of 7.1.1.3 are not applicable at the beginning and the en

35、d of the coil over a length of 3 m. 9.2 Width The width shall be measured perpendicular to the longitudinal axis outside the area of any end tongue. 9.3 Straightness of edges The tolerance on straightness of edges (see 8.1) is the maximum deviation between a longitudinal edge and the straight line p

36、assing through the two ends of the reference measuring length (2500 mm). The straightness shall be measured on the concave side of the product and, for coils, outside any end tongue area (see figure i). COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling Servic

37、esPage 15 EN 10048 : 1996 Direction of rolling L is the reference measuring length W is the width of product c is the tolerance on straightness Figure 1 : Straightness of edges 10 Packing The coils shall be secured so that they cannot be damaged nor unwind during normal careful loading, transportati

38、on and storage. The cut lengths shall be packed so that they do not become damaged when carefully loaded, transported and stored. 11 Options (see 5.2) 1. If edges are to be slit (see 4.2.2) 2. If coils may be delivered with end tongues (see 4.2.3). 3. If the total thickness tolerances shall be all o

39、ver or all under (see 7.1.1.2). 4. If the width tolerance shall be symmetrical all plus or all minus (see 7.2.1; Table 5 : Note 1 and Table 6 : Note 1). 5. If narrow strip with slit edges shall have tighter thickness tolerances (see 7.2.1; Table 6 : Note 2). 6. If cut lengths are supplied, whether n

40、ormal or fine tolerances are required (see 7.3.1). COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 16 EN 10048 : 1996 Annexes Annex A (informative) List of corresponding national designations, standards or specifications for categories B, C and

41、 D of table 4 As a supplement to table 4, tables A.l to A.3 include the corresponding national designations, standards or specifications for categories B, C and D. In these tables, in the event of a national standard having been recently replaced by a European Standard, the old designation and the c

42、orresponding standard are indicated in brackets. COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 17 EN 10048 : 1996 Standardized in Table A. 1 : Corresponding national designations and standards for category B (10% Designation increase) Europe

43、Designation E295; E335; E360 s355 s355 s355 s355 P295: P355 c35 C35E C36 c45 C45E C46 c50 C50E 16Mo3 20MnB5 30MnB5 38MnB5 28Mn6 27MnCrB5-2 33M nC rB5 -2 39MnCrB6-2 38CR 46Cr2 3404 41 Cr4 45 Cr2 38 Cr4 I6 MnC r5 13CrMo4-5 IOCrMo9-10 All ferntic and manensitic stainless steels I Germanv EN 10025 EN 10

44、025 EN 10155 EN 10149-2 EN 10149-3 EN 10113 EN 10028-2 (Si 50-2; St 60-2; SI 70-2) (St 52-3) (WtSt 52) (QStE340) (StE355; RSiE355TM) EN 10083-2 EN 10083-1 EU 86-70 EN 10083-2 EN 10083-1 EU 86-70 EN 10083-2 EN 10083.1 EN 10028-2 EN 10083-3 EN 10083-3 EN 10083-3 EN 10083-1 EN 10083-3 EN 10083-3 EN 100

45、83-3 EN 10083-1 EN 10083-1 EN 10083-1 EN 10083-1 EU 86-70 EU 86-70 prEN 10084 EN 10028-2 (C 35) (Ck 35) Cf 35 (C 45) (Ck 45) c 45 w Cf 45 (C 50) Ck SO) (15 Mo 3) (19 MnB 4) (28 Mn 6) (32 Cr 2) (38 Cr 2) (46 Cr 2) (28 Cr 4) (34 Cr 4) (41 Cr 4) 17 Cr 3 20 Cr 4 45 Cr 2 38 Cr 4 42 Cr 4 16 MnCr 5 20 MnCr

46、 5 22 CrMoS 35 (13 CrMo44) EN 10028-2 (10 CrMo 9 IO) martensitic stainless steels Standardized in (DIN 17 100) (DIN 17 100) (SEW 087) (SEW 092) (DIN 17 102: SEW 083) (DIN 17 155) (DIN 17 200) (DIN 17 200) DIN 17 212 (DIN 17 200) (DIN 17 200) DIN 17 350 DIN 17 212 (DIN 17 200) (DIN 17 2001 (DIN 17 15

47、5) (DIN 1654 T4) (DIN 17 200) (DIN 17 200) (DIN 17 200) (DIN 17 200) (DIN 17 200) (DIN 17 200) (DIN i7 200) DIN 17 210 DIN 17 210 DIN 17 212 DIN 17 212 DIN 17 212 DIN i7 210 DIN i7 210 DIN i7 210 (DIN 17 155) (DIN 17 155) (DIN 17 440 ) France Designation (A 50-2; A 60-2; A 70-2) (E 36-3; E 36-4) (E

48、36 W) (E 3550) (E 355) (A 48; A 52) (AF 55 C 35) (XC 38) XC 3R TC (AF 65 C 45) (XC 45) (XC 42 H 1) XC 50) (15 D 3) (20 MB 5) (38 MB 5) (38 C 2) (32 C 4) (42 C 4) (42 C 2) (42 C 4) 16MC 5 20MC 5 (15 CD 2.05) (15 CD 4.05) (i2 CD 9.10) All femtic and martensitic stainless steels Standardized in (NF A 3

49、5-501) (NF A 36-101) (NF A 35-502) (NF A 36-231) (NF A 36201) (NF A 36-205) (NF A 35-101) (NF A 35-553) not standardized (NF A 35-101) (NF A 35-553) (NF A 35-552) (NF A 35-553) (NF A 36-206) (NF A 35-556) (NF A 35-556) (NF A 35-552) (NF A 35-552) (NF A 35-552) (NF A 35-552) (NF A 35-552) NF A 35-551 NF A 35-551 (NF A 36-206) (NF A 36-206) (NF A 36-210) (NF A 36-206) (NF A 35-573) COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 18 EN 10048 : 1996 Table A.1 : Corresponding national designations and standards for cate