DIN EN 10034-1994 Structural steel I and H sections tolerances on shape and dimensions German version EN 10034 1993《I型和H型结构钢 形状和尺寸公差》.pdf
《DIN EN 10034-1994 Structural steel I and H sections tolerances on shape and dimensions German version EN 10034 1993《I型和H型结构钢 形状和尺寸公差》.pdf》由会员分享,可在线阅读,更多相关《DIN EN 10034-1994 Structural steel I and H sections tolerances on shape and dimensions German version EN 10034 1993《I型和H型结构钢 形状和尺寸公差》.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、UDC 669.14.018.29-423.1 :621.713.1 DEUTSCHE NORM March 1994 I I Structural steel I and H sections English version of DIN EN 10034 Tolerances on shape and dimensions DIN - EN 10034 I- und H-Profile aus Baustahl; Grenzabmae und Formtoleranzen This standard, together with the March 1994 editions of DIN
2、 1025 Parts 2 to 5, supersedes the October 1963 editions of DIN 1025 Parts 2, 3 and 4 and the March 1965 edition of DIN 1025 Part 5. European Standard EN 10034:1993 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been prepared by ECISS/TC
3、11. The responsible German body involved in its preparation was the Normenausschu Eisen und Stahl (Steel and Iron Standards Committee), Technical Committee Warmgewalzte Profilerzeugnisse. The present standard specifies dimensional and geometrical tolerances for I and H sections and bearing piles, wh
4、ich had been given previously in DIN 1025 Parts 2 to 5. The values no longer apply for specific section shapes. The scope of the present standard covers many more sizes than the DIN Standards did, and includes, for example, a flange width of 420 mm and a flange thickness of 75 mm. Negoti- ations are
5、 continuing within ECISS/TC 11 for harmonizing the sizes of I and H sections. In specifying tolerances on the cross-sectional dimensions, ECISS/TC 11 endeavoured to specify values which, where lower limit deviations are chosen, do not lead to an automatic reduction of static parameters, which would
6、necessitate the use of higher factors of safety when designing the particular steel structure. These efforts resulted in an asymmetrical distribution of limit deviations, and in a reduction of the tolerance on nominal mass for single sections to * 4 %. The DIN Standards corresponding to the European
7、 Standard and EURONORMs referred to in clause 2 of the EN are as follows: EN Standard DIN Standard EN 1 O 079 DIN EN 10079 EURONORM 19 DIN 1025 Part 5 EURONORM 53 DIN 1025 Parts2 to 4 Standards referred to (and not included in Normative references) DIN EN 10079 Definition of steel products DIN 1025
8、Part 2 Hot rolled I and H sections (IPB and IB series); dimensions, mass and static parameters DIN 1025 Part 3 Hot rolled I and H sections (IPBI series); dimensions, mass and static parameters DIN 1025 Part 4 Hot rolled I and H sections (IPBv series); dimensions, mass and static parameters DIN 1025
9、Part 5 Hot rolled I and H sections (IPE series); dimensions, mass and static parameters Continued overleaf. EN comprises 5 pages. Beuth Verlag GmbH, Berlin, has the exclusive right of sale for German Standards (DIN-Normen). 07.94 DIN EN 10034 Engl. Price group 7 Sales No. 1107 Page 2 DIN EN 10034 Pr
10、evious editions DIN 1612: 09.24, 01.32, 03.43; DIN 1025 Part 2: 04.26, 10.28, 12.29, 04.32, 09.39, 07.40x, 07.59, 10.63; DIN 1025 Part 3: 10.63; DIN 1025 Part 4: 10.63; DIN 1025 Part 5: 03.65. Amendments In comparison with the October 1983 editions of DIN 1025 Parts2 to 4 and the March 1965 edition
11、of DIN 1025 Part 5, the following amendments have been made. a) The specifications have been restricted to dimensional and geometrical tolerances. b) Some of the limit deviations for section height, flange width and thickness and web thickness have been changed (cf. table 1). c) Some of the toleranc
12、es on parallelism of flange, section symmetry and straightness of web have been changed (cf, tables 2 and 3). d) The tolerance on nominal mass has been reduced to f 4 % EUROPEAN STANDARD EN 10034 NORME EUROPENNE EUROPAISCHE NORM September 1993 UDC 669.14.018.29-423.1 :621.713.1 Descriptors: Iron and
13、 steel products, I beams, Structural steels, dimensional tolerances, form tolerances. English version Structural steel I and H sections Tolerances on shape and dimensions POL .elles I E ?n acier de con- I- und H-Profile aus Stahl; Grenzabm und Formtoleranzen struction; tolrances de formes et de dime
14、nsions This European Standard was approved by CEN on 1993-08-30. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical re
15、ferences concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member
16、 into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden
17、, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 1993. Copyright reserved to all CEN members. Ref. No. EN 10034:1993 E Page 2 EN 10034:1993 Contents li
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DINEN100341994STRUCTURALSTEELIANDHSECTIONSTOLERANCESONSHAPEANDDIMENSIONSGERMANVERSIONEN100341993I 结构钢

链接地址:http://www.mydoc123.com/p-663622.html