DIN EN 10025-2-2005 Hot rolled products of structural steels - Part 2 Technical delivery conditions for non-alloy structural steels German version EN 10025-2 2004《结构钢制热轧产品 第2部分 非合金.pdf

《DIN EN 10025-2-2005 Hot rolled products of structural steels - Part 2 Technical delivery conditions for non-alloy structural steels German version EN 10025-2 2004《结构钢制热轧产品 第2部分 非合金.pdf》由会员分享，可在线阅读，更多相关《DIN EN 10025-2-2005 Hot rolled products of structural steels - Part 2 Technical delivery conditions for non-alloy structural steels German version EN 10025-2 2004《结构钢制热轧产品 第2部分 非合金.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、DEUTSCHE NORM April2005 DIN EN 10025-2 DIN ICS 77.140.10; 77.140.45; 77.140.50 Supersedes February 2005 edition. Hot rolled products of structural steels Part 2: Technical delivery conditions for non-alloy structural steels English version of DIN EN 10025-2 Warmgewalzte Erzeugnisse aus Baustahlen-Te

2、il 2: Technische Lieferbedingungen fOr unlegierte Baustahle A comma is used as the decimal marker. National foreword This standard has been prepared by ECISS/TC 10. The responsible German body involved in its preparation was the Normenausschuss Eisen und Stahl (Steel and Iron Standards Committee), T

3、echnical Committee Stahle fCrr den Stahlbau. Amendments This standard differs from DIN EN 10025, March 1994 edition, in that it has been completely revised and from the February 2005 edition in that some printing errors have been removed in the German version. Previous editions DIN 1611:1924-09,1928

4、-01,1929-04,1930-08, 1935-12; DIN 1612:1932-01, 1943x-03; DIN 1620: 1924-09, 1958-03; DIN 1621: 1924-09; DIN 1622: 1933-12; DIN 17100: 1957-10, 1966-09, 1980-01; DIN EN 10025: 1991 -01, 1994-03; DIN EN 10025-2: 2005-02. No part of this standard may be reproduced without the prior permission of DIN D

5、eutsches lnstitut fur Normung e. V, Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen). Document comprises 33 pages. English price group 15 www.din.de www.beuth.de 1111 11 1111 1111 111111111 06.05 9640258 EUIROPEAN STANDARD NORME EURO

6、PEENNE EUROPAISCHE NORM ICS 77.140.10; 77.140.45; 77.140.50 English version EN 10025-2 November 2004 Supersedes EN 10025 : 1990. Hot rolled products of structural steels Part 2: Technical delivery conditions for non-alloy structural steels Produits lamines a chaud en aciers Warmgewalzte Erzeugnisse

7、aus Bau-de construction - Partie 2: Conditions stahlen - Teil 2: Technische Lieferbe-techniques de livraison pour les aciers dingungen fur unlegierte Baustahle de construction non allies This European Standard was approved by CEN on 2004-04-01. CEN members are bound to comply with the CEN/CENELEC In

8、ternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN membe

9、r. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are

10、 the national standards bodies of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, and t

11、he United Kingdom. CEN European Committee for Standardization Comite Europeen de Normalisation Europaisches Komitee fUr Normung Management Centre: rue de Stassart 36, B-1050 Brussels 2004. CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref.

12、 No. EN 10025-2 : 2004 E Page2 EN 10025-2: 2004 Contents Page Foreword 3 1 Scope . 4 2 Normative references 4 2.1 General standards . 4 2.2 Standards on dimensions and tolerances (see 7.7.1) 5 2.3 Standards on testing . 6 3 Terms and definitions . 6 4 Classification and designation . 6 4.1 Classific

13、ation 6 4.1.1 Main quality classes 6 4.1.2 Grades and qualities . 7 4.2 Designation 7 5 Information to be supplied by the purchaser . 7 5.1 Mandatory information 7 5.2 Options . 8 6 Manufacturing process . 8 6.1 Steel making process 8 6.2 Deoxidation 8 6.3 Delivery conditions 8 7 Requirements . 9 7.

14、1 General 9 7.2 Chemical composition 9 7.3 Mechanical properties . 9 7.3.1 General 9 7.3.2 Impact properties . 10 7.3.3 Improved deformation properties perpendicular to the surface 10 7.4 Technological properties 10 7 .4.1 Weldability 1 0 7 .4.2 Formability 1 0 7.4.3 Suitability for hot-dip zinc-coa

15、ting . 11 7 .4.4 Machinability 12 7.5 Surface properties . 12 7 .5.1 Strip . 12 7 .5.2 Plates and wide flats 12 7 .5.3 Sections 12 7 .5.4 Bars and rods . 12 7.6 Internal soundness 12 7. 7 Dimensions, tolerances on dimensions and shape, mass 13 8 Inspection . 13 8.1 Ge nellal 13 8.2 Type of inspectio

16、n and inspection document 13 8.3 Frequency of testing . 13 8.3.1 Sampling . 13 8.3.2 Test units 13 8.3.3 Verification of chemical composition 14 8.4 Tests to be carried out for specific inspection . 14 9 Preparation of samples and test pieces 14 Page3 EN 10025-2: 2004 9.1 Selection and preparation o

17、f samples for chemical analysis . 14 9.2 Location and orientation of samples and test pieces for mechanical tests . 14 9.2.1 General . 14 9.2.2 Preparation of samples 15 9.2.3 Preparation of test pieces . 15 9.3 Identification of samples and test pieces . 15 10 Test methods . 15 10.1 Chemical analys

18、is . 15 10.2 Mechanical tests 15 10.3 Ultrasonic testing 15 10.4 Retests 15 11 Marking, labelling, packaging 15 12 Complaints . 15 13 Options (see 5.2) 16 Annex A (informative) List of corresponding former designations 30 Annex B (informative) List of national standards which correspond with EURONOR

19、MS referenced . 31 Bibliography 32 Foreword This document (EN 10025-2:2004) has been prepared by Technical Committee ECISS/TC 10 “Structural steels- Grades and qualities“, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard. either by publ

20、ication of an identical text or by endorsement, at the latest by May 2005, and conflicting national standards shall be withdrawn at the latest by May 2005. This document supersedes EN 10025:1990 + A1:1993, Hot rolled products of non-alloy structural steels Technical delivery conditions. The titles o

21、f the other Parts of this European Standard are: Part 1: General technical delivery conditions; Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels; Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structur

22、al steels; Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance; Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition. This document has been prepared under a mand

23、ate given to CEN by the European Commission and the European Free Trade Association. and supports essential requirements of the EU Construction Products Directive (89/106/EEC. For relationship with the EU Construction Products Directive, see informative Annex ZA of EN 1 0025-1 :2004. Accordling to t

24、he CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, M

25、alta, Netherlands, Norway, Portugal, Slovakia, Sllovenia, Spain, Sweden, Switzerland and the United Kingdom. Page4 EN 10025-2: 2004 1 Scope Part 2 of this document, in addition to Part 1, specifies the technical delivery conditions for flat and long products and semi-finished prroducts which are mea

26、nt for further processing to flat and long products of hot rolled non-alloy quality steels in the grades and qualities given in Tables 2 to 6 (chemical composition) and Tables 7 to 9 (mechanical properties) in the delivery conditions as given in 6.3. Three engineering steels are also specified in th

27、is document (see Tables 3 and 5) (chemical composition) and Table 8 (mechanical properties). This document does not apply to structural hollow sections and tubes (see EN 10210-1 and EN 10219-1 ). The technical delivery conditions apply to thicknesses ;: 3 mm and $ 150 mm for long products of steel g

28、rade S450JO. The technical delivery conditions apply to thicknesses $ 250 mm for flat and long products of all other grades and qualities. In addition for flat products of qualities J2 and K2 the technical conditions apply to thicknesses $ 400 mm. Products made of steel grades S185, E295, E335 and E

29、360 cannot be CE marked. The steels specified in this Part 2 are not intended to be heat treated except products delivered in delivery condition +N. Stress relief annealing is permitted (see also the NOTE in 7.3.1.1 of EN 10025-1:2004). Products delivered in +N condition can be hot formed and/or nor

30、malized after delivery (see Clause 3). NOTE 1 Semi-finished products which are to be converted to rolled finished products conforming to this document should be the subject of special agreement at the time of the enquiry and order. The chemical composition can also be agreed at the time of the order

31、, however the values should be within the limits of Tables 2 and 3. NOTE 2 For certain grades and product forms suitability for particular applications may be specified at the time of the enquiry and order (see 7.4.2, 7.4.3 and Table 10). 2 Normative references The following referenced documents are

32、 indispensable torr the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. 2.1 General standards EN 1011-2, Welding- Recommendations for welding of metallic mate

33、rials- Part 2: Arc welding offerritic steels. EN 10020, Definition and classification of grades of steel. EN 10025-1:2004, Hot rolled products of structural steels- Part 1: General technical delivery conditions. EN 1 0027-1, Designation systems for steels - Part 1: Steel names, principal symbols. EN

34、 1 0027-2, Designation systems for steels - Part 2: Numerical system. EN 10163-1, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 1: General requirements. EN 10163-2, Delivery requirements for surface condition of hot-rolled steel plates, wide fla

35、ts and sections -Part 2: Plates and wide flats. EN 10163-3, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections -Part 3: Sections. PageS EN 10025-2: 2004 EN 10164, Steel products with improved deformation properties perpendicular to the surface of the prod

36、uct Technical delivery conditions. EN 10221, Surface quality classes for hot-rolled bars and rods- Technical delivery conditions. CR 10260, Designation systems for steels - Additional symbols. 2.2 Standards on dimensions and tolerances (see 7.7.1) EN 10017, Non-alloy steel rod for drawing and/or col

37、d rolling- Dimensions and tolerances. EN 10024, Hot rolled taper flange I sections- Tolerances on shape and dimensions. EN 10029, Hot rolled steel plates 3 mm thick or above - Tolerances on dimensions, shape and mass. EN 10034, Structural steel/ and H sections - Tolerances on shape and dimensions. E

38、N 10048, Hot rolled narrow steel strip- Tolerances on dimensions and shape. EN 10051, Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels- Tolerances on dimensions and shape. EN 10055, Hot-rolled steel equal flange tees with radiused root and toes - Dimensions and t

39、olerances on shape and dimensions. EN 10056-1, Structural steel equal and unequal leg angles - Part 1: Dimensions. EN 10056-2, Structural steel equal and unequal leg angles- Part 2: Tolerances on shape and dimensions. EN 10058, Hot rolled flat steel bars for general purposes - Dimensions and toleran

40、ces on shape and dimensions. EN 10059, Hot rolled square steel bars for general purposes- Dimensions and tolerances on shape and dimensions. EN 10060, Hot rolled round steel bars for general purposes- Dimensions and tolerances on shape and dimensions. EN 1 0061, Hot rolled hexagon steel bars for gen

41、eral purposes - Dimensions and tolerances on shape and dimensions. EN 10067, Hot rolled bulb flats - Dimensions and tole.rances on shape, dimensions and mass. EN 10162, Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances. EN 10279, Hot rolled steel

42、 channels- Tolerances on shape and dimensions. Page6 EN 10025-2: 2004 2.3 Standards on testing EN 10160, Ultrasonic testing of steel flat product of thickness equal to or greater than 6 mm (reflection method). EN 10306, Iron and steel- Ultrasonic testing of H beams with parallel flanges and IPE beam

43、s. EN 10308, Non-destructive testing - Ultrasonic testing of steel bars. EN ISO 643, Steels- Micrographic determination of the apparent grain size (ISO 643:2003). 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10025-1:2004 and the following apply. 3.

44、1 normalizing rolling rolling process in which the final deformation is carried out in a certain temperature range leading to a material condition equivalent to that obtained after normalizing so that the specified values of the mechanical properties are retained even after normalizing The abbreviat

45、ed form of this delivery condition is +N NOTE In international publications for both the normalizing rolling, as well as the thermo-mechanical rolling, the expression “controlled rolling“ may be found. However in view of the different applicability of the products a distinction of the terms is neces

46、sary. 3.2 as-rolled delivery condition without any special rolling and/or heat treatment condition. The abbreviated form of this dlelivery condition is +AR 3.3 thermomechanical rolling rolling process in which the final deformation is carried out in a certain temperature range leading to a material

47、condition with certain properties which cannot be achieved or repeated by heat treatment alone NOTE 1 Subsequent heating above 580 oc may lower the strength values. If temperatures above 580 oc are needed reference should be made to the supplier. NOTE 2 Thermomechanical rolling leading to the delive

48、ry condition M can include processes with an increasing cooling rate with or without tempering including self-tempering but excluding direct quenching and quenching and tempering. NOTE 3 In some publications the word TMCP (Thermomechanical Control Process) is also used. 4 Classifiication and designa

49、tion 4.1 Classification 4.1.1 Main quality classes The steel grades specified in this document shall be classified as non-alloy quality steels according to EN 10020. 4.1.2 Grades and qualities Page 7 EN 10025-2: 2004 This document specifies eight steel grades 8185, 8235, 8275, 8355, 8450, E295, E335 and E360. They differ in their mechanical properties. The steel grades S235 and S275 may be supplied in qualities JR, JO and J2. The st eel grade 8355 may be supplied in qualities JR, JO, J2 and K2. The steel grade 8450 is supplied in quality JO. The qualities differ in specified impact e