DIN EN 10024-1995 Hot-rolled taper flange I sections - Tolerances on shape and dimensions German version EN 10024 1995《热轧锥形法兰盘工字钢 外型和尺寸公差 德文版本 EN 10024 1995》.pdf

《DIN EN 10024-1995 Hot-rolled taper flange I sections - Tolerances on shape and dimensions German version EN 10024 1995《热轧锥形法兰盘工字钢 外型和尺寸公差 德文版本 EN 10024 1995》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 10024-1995 Hot-rolled taper flange I sections - Tolerances on shape and dimensions German version EN 10024 1995《热轧锥形法兰盘工字钢 外型和尺寸公差 德文版本 EN 10024 1995》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、DEUTSCHE NORM Mav 1995 Hot rolled steel taper flange I sections Tolerances on shape and dimensions English version of DIN EN IS0 10024 DIN - EN 10024 ICs 77.140.70 Descriptors: Steel, I sections, tolerances. This standard, together with DIN 1025-1, May 1995 edition, su- persedes DIN 1055-1, October

2、1963 edition. I-Profile mit geneigten inneren Flanschflchen; Grenzabmae und Form- toleranzen European Standard EN 10024:1995 has the status of a DIN Standard. A comma has been used as the decimal marker. National foreword This standard has been prepared by ECISSTTC 11. The responsible German body in

3、volved in its preparation was the Normenausschu Eisen und Stahl (Steel and Iron Stand- ards Committee), Technical Committee Warmgewalzte Profilerzeugnisse. It should be noted that it is not intended to specify nominal sizes of I sections. Amendments In comparison with DIN 1025-1, October 1963 editio

4、n, the following amendments have been made: a) Sizes of I sections are no longer specified. b) Some tolerances on flange thickness, web thickness, out-of-squareness, web off-centre, straightness and length have been amended. c) A limit deviation of +4% has been specified for the mass. Previous editi

5、ons DIN 1612: 1924-09, 1932-01, 1943X-03; DIN 1025-1: 1926-10, 1932-02, 1939-08, 194OX-07, 1959-07, 1963-10. EN comprises 3 pages. Beuth verlag GmbH, Berlin, has the exclusive right of saie for German Standards (DIN-Normen) 11.95 DIN EN 1 O 024 Engl. Price group 5 Sales No. 11 05 COPYRIGHT DIN DEUTS

6、CHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesCOPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesEUROPEAN STANDARD EUROPAISCHE NORM NORME EUROPENNE EN 10024 March 1995 ICs 77.140.70 Descriptors: Steel, I sections, tole

7、rances. English version Hot rolled steel taper flange I sections Tolerances on shape and dimensions Poutrelles en I ailes inclines lamines chaud; tolrances de forme et de di- mensions toleranzen I-Profile mit geneigten inneren Flansch- flchen; Grenzabmae und Form- This European Standard was approved

8、 by CEN on 1995-02-06. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards

9、 may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the

10、Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN Europ

11、ean Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, 8-1050 Brussels O 1995. Copyright reserved to all CEN members. Ref. No. EN 10024:1995 E COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Infor

12、mation Handling ServicesPage 2 EN 10024:1995 Contents Page Foreword 2 1 Scope 2 2 Normative references . 2 3 Definitions 2 4 Tolerances on dimensions and shape . 2 5 Tolerance on mass . 2 6 Tolerance on length 2 Foreword This European Standard has been prepared by ECISS/TC 11 Structural steel sectio

13、ns, the Secretariat of which is held by BSI. Its specifications are based on proposals made by ECISSTTC 11NVG 3. This European Standards shall be given the status of a national standard, either by publication of an identical text or by endorsement, and conflicting national standards withdrawn, by Se

14、ptember 1995 at the latest. In accordance with the CENKENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, S

15、witzerland, United Kingdom. 1 Scope This European Standard specifies requirements for toler- ances on dimensions, shape and mass of hot rolled steel taper flange I sections, except stainless steel taper flange I sections. 2 Normative references This European Standard incorporates, by dated or undate

16、d reference, provisions from other publications. These nor- mative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when

17、incorporated in it by amendment or revision. For un- dated references, the latest edition of the publication re- ferred to applies. EN 10079 Definition of steel products 3 Definitions For the purposes of this European Standard, the definitions given in EN 1 O 079 apply. 4 Tolerances on dimensions an

18、d shape 4.1 Height Any deviations of the height (h) from the nominal value shall be within the tolerance given in table 1. 4.2 Flange width Any deviations of the flange width(b) from the nominal value shall be within the tolerance given in table 1. 4.3 Web thickness Any deviations of the web thickne

19、ss (s) from the nominal value, when measured at the mid-width position of the web, shall be within the tolerance given in table 1. 4.4 Flange thickness Any deviations of the flange thickness (t) from the nominal value, when measured at a distance equal to b/4 from the mid-width position of the flang

20、e, shall be within the toler- ance given in table 1. 4.5 Out-of-squareness The out-of-squareness of the section (k + k) shall not ex- ceed the value given in table 1. 4.6 Web off-centre The mid-thickness of the web shall not deviate from the mid-width position on the flange by more than the distance

21、 (e) given in table 1. 4.7 Straightness The straightness (qXx or q,) shall comply with the require- ments given in table 1. 5 Tolerance on mass The mass of a batch or piece shall be within f 4,O % of the calculated mass (see table 1). The mass deviation is the difference between the actual mass of t

22、he batch or piece and the calculated (theoretical) mass. The theoretical mass shall be determined taking the density as 7,85 kg/dm3. 6 Tolerance on length The sections shall be cut to ordered lengths to tolerances (see table 1) of either a) f50 mm or, by agreement, b) +lo: mm. COPYRIGHT DIN DEUTSCHE

23、S Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 3 EN 10024:1995 s 7 7s110 10 s tj 7 7tj10 10 t 20 20 t Table 1: Tolerances on dimensions of hot rolled steel taper flange I sections + 0.51- 1 .O + 0.71- 1,5 + 1 .Ol- 2,o + 1 #5l- 0,5 + 2,Ol- 1 ,o + 2,51- 1,5 + 251- 2,

24、O Designation 3 I t L L I Batch or piece Property Height h Flange width b Web thickness S Flange thickness t Out-of-squareness k + k Web off-centre e Straightness 9xx and qyy Mass Length L Dimensions in mm Range Tolerance + 2.01- 2.0 + 3,Ol- 3,O + 401- 4,O h 5 200 200 h 5 400 400 h bi 75 75 b I 100

25、100 b I 125 125 b + 1,51- 1,5 + 2,Ol- 2,o + 2.51- 2,5 + 3,Ol- 3,O b j 100 100 b 2.0 246 of b b 100 100 b 80 h 180 180 h 360 360 h 0.3 Yo of L 0,1546 of L 0.1 96 of L 1 f 4% + 501- 50 (standard) + 10010 (by agreement) COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling Services