DIN 59740-2004 Sheets of wrought nickel and wrought nickel alloys hot rolled - Dimensions and tolerances on dimensions and form《锻镍和锻镍合金热轧薄板 尺寸及尺寸与形状公差》.pdf

《DIN 59740-2004 Sheets of wrought nickel and wrought nickel alloys hot rolled - Dimensions and tolerances on dimensions and form《锻镍和锻镍合金热轧薄板 尺寸及尺寸与形状公差》.pdf》由会员分享，可在线阅读，更多相关《DIN 59740-2004 Sheets of wrought nickel and wrought nickel alloys hot rolled - Dimensions and tolerances on dimensions and form《锻镍和锻镍合金热轧薄板 尺寸及尺寸与形状公差》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 No part of this translation may be reproduced without the prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).English price group 7 www.din.de www.beuth.de04.05 9608911Document

2、 comprises 7 pages.ICS 77.150.40Bleche aus Nickel und Nickel-Knetlegierungen, warmgewalzt Mae, Grenzabmae und FormtoleranzenIn keeping with current practice in standards published by the International Organization for Standardization (ISO), a comma has been used throughout as the decimal marker.Hot

3、rolled nickel and nickel alloy sheet and plateDimensions, tolerances and material groupsTranslation by DIN-Sprachendienst.In case of doubt, the German-language original should be consulted as the authoritative text.Supersedes January 1975 edition.ForewordThis standard has been prepared by the Normen

4、ausschuss Nichteisenmetalle (Nonferrous Metals Stand-ards Committee), Technical Committee Nickelwerkstoffe.AmendmentsThis standard differs from the January 1975 edition in that it has been revised in form and substance.Previous editionDIN 59740: 1975-01.All dimensions are in millimetres.1 ScopeThis

5、standard species the dimensions, dimensional and form tolerances, and material groups for hot rolled nickel and nickel alloy sheet and plate in thicknesses from 2 mm to 150 mm and widths up to 3 000 mm.2 Normative referencesThis standard incorporates, by dated or undated reference, provisions from o

6、ther publications. These nor-mative references are cited at the appropriate places in the text and the titles of the publications are listed below. For dated references, subsequent amendments to or revisions of any of these publications apply to this standard only when incorporated in it by amendmen

7、t or revision. For undated references, the latest edition of the publication referred to applies.DIN 17740 Wrought nickel Chemical compositionDIN 17742 Wrought nickel-chromium alloys Chemical compositionDIN 17743 Wrought nickel-copper alloys Chemical compositionDIN 17744 Wrought nickel-molybdenum an

8、d nickel-chromium alloys Chemical compositionDIN 17750 Nickel and wrought nickel and alloy plate, sheet and strip Requirements and testing July 200459740Page 2DIN 59740 : 2004-073 Designation3.1 ElementsThe designation of nickel sheet and plate shall comprise its name, the number of this standard, i

9、ts thickness, width and length (all dimensions in mm), the symbol designating its edge nish, and its grade or material number and heat treatment condition as in DIN 17750.3.2 Standard designationEXAMPLE no. 1:Designation of nickel plate of grade NiCr15Fe (material number: 2.4816), 25 mm thick, 1 500

10、 mm wide and 4 000 mm long, with cut edges (GK), supplied in condition F55:Nickel plate DIN 59740 25 1500 4000 GK NiCr15Fe F55orNickel plate DIN 59740 25 1500 4000 GK 2.4816 F55EXAMPLE no. 2:Designation of nickel plate of grade NiMo28 (material number: 2.4617), 10 mm thick, 160 mm wide, 2 300 mm lon

11、g, with closer tolerances on length and width (E), with special edge nish (SK), supplied in condition F75:Nickel plate DIN 59740 10 160E 2300E SK NiMo28 F75orNickel plate DIN 59740 10 160E 2300E SK 2.4617 F753.3 Designation for order purposesEXAMPLE no.1:Designation when ordering 50 nickel plates as

12、 specied in this standard, of grade LC-NiCr15Fe (material number 2.4817), 10 mm thick, 120 mm wide and 2 000 mm long, with cut edges (GK), supplied in condition F55:50 nickel plates DIN 59740 10 120 2000 GK LC-NiCr15Fe F55or50 nickel plates DIN 59740 10 120 2000 GK 2.4817 F55EXAMPLE no. 2:Designatio

13、n when ordering 6 nickel sheets of grade NiCr20Ti (material number: 2.4951), 2 mm thick, 1 020 mm wide, 1 950 mm long, with closer tolerances on length and width (E), with special edge nish (SK), supplied in condition F65:6 nickel sheets DIN 59740 2 1020E 1950E SK NiCr20Ti F65or6 nickel sheets DIN 5

14、9740 2 1020E 1950E SK 2.4951 F654 Dimensions and tolerances4.1 Thickness, width and length4.1.1 The thickness of sheet and plate, and the relevant tolerances shall be as specied in tables 1 and 2.The thickness shall be measured at the centre of each of the four edges of the sheet/plate, at a distanc

15、e of at least 25 mm from the edge. The mean of the four readings shall be taken as the thickness. The deviation of a single value may exceed the values given in the tables by no more than 50 %. The difference between the measured maximum and minimum values shall not be greater than the tolerance spe

16、cied for the mean (i.e. the sum of the upper and lower deviations).EXAMPLEFor a plate, 17 mm thick, 1000 mm wide, of material group II,a) the limit deviations for the mean thickness may be +0,60 mm and 0,30 mm andb) the limit deviations for a single value may be +0,90 mm and 0,45 mm,and, for a singl

17、e plate, the difference between the measured maximum and minimum thicknesses may be 0,9 mm.Page 3DIN 59740 : 2004-07Table 1: Limit deviations for thickness for material group I sheet/platePage 4DIN 59740 : 2004-074.1.2 The length and width of sheet and plate and the relevant tolerances shall be as s

18、pecied in table 3. Subject to agreement, the lower deviation for width may be equal to the upper deviation.Table 3: Tolerances on length and width of sheet/plateNominal thickness Limit deviations for lengths and widths Standard design Sheet/plate made to closer tolerancesFor lengths/widths For lengt

19、hs/widthsup to 2 000over 2 000 up to 3 000over 3 000 up to 4 000over 4 000 up to 6 000 up to 2 000over 2 000 up to 3 000over 3 000 up to 4 000over 4 000 up to 6 000Up to 5+ 10+ 0+ 15+ 0+ 20+ 0+ 30+ 0+ 5+ 0+ 8+ 0+ 10+ 0+ 15+ 0Over 25 up to 20+ 12+ 0+ 15+ 0+ 20+ 0+ 30+ 0+ 5+ 0+ 8+ 0+ 10+ 0+ 15+ 0Over

20、20 up to 50+ 15+ 0+ 15+ 0+ 20+ 0+ 30+ 0+ 5+ 0+ 8+ 0+ 10+ 0+ 15+ 04.2 Edge camberThe deviation from straightness of edges shall not exceed 2 mm per metre of edge length, with a linear in-crease.4.3 SquarenessThe tolerance on angularity (difference between lengths of diagonals) shall be as specied in

21、table 4.Table 2: Limit deviations for thickness for material group II sheet/platePage 5DIN 59740 : 2004-07Table 4: Tolerances on angularityNominal widthAngularity tolerance for lengthsup to 2 000over 2 000 up to 3 000over 3 000 up to 4 000over 4 000 up to 6 000Up to 1 000 8 9 10 12Over 1 000 up to 1

22、 500 9 10 11 13Over 1 500 up to 2 000 11 12 13 15Over 2 000 up to 3 000 13 15 17 204.4 Flatness tolerancesFlatness tolerances shall be as specied in table 5.Deviation from atness is the deviation of any area on a sheet/plate from a given plane when measured with the sheet/plate in the unloaded condi

23、tion, and disregarding the permissible deviation from thickness. When uneven areas do not extend along the entire length of the sheet/plate, the deviation from atness shall be not greater than 1 % of the length of the uneven area and shall not exceed the tolerances specied in table 5.Table 5: Flatne

24、ss tolerancesNominal thicknessFlatness tolerance for widthsup to 1 000over 1 000 up to 1 500over 1 500 up to 2 000over 2 000 up to 3 000Up to 3 15 20 25 Over 3 up to 25 10 15 20 25Over 25 10 15 15 154.5 Edge nish4.5.1 Sheet/plate may be supplied in the following forms:a) with edges unnished (NK);b)

25、with ame-cut or arc plasma-cut edges (BK);c) with edges cut by shears (GK);d) with a special edge nish (SK) (e.g. edges cut by machining, chamfered, deburred).4.5.2 Cutting sheet/plate using guillotine shears results in steps forming along the longitudinal edges of the material. The width of such st

26、eps shall be 50 % smaller than the tolerances specied in table 3.4.5.3 The supply of sheet/plate with unnished edges shall be subject to agreement. In this case, the toler-ances specied for length and width do not apply.4.5.4 It should be noted that sheet/plate with cut edges have a burr, which is a

27、cceptable if the burr height is less than 10 % of the material thickness. If the edge nish is to meet special requirements, this is to be indicated when ordering.5 MaterialsNickel and nickel alloy sheet/plate shall conform to DIN 17750, unless otherwise agreed.Since sheet/plate is not available in a

28、ll grades and sizes, details should be agreed upon at the time of order-ing. This standard classies nickel sheet/plate into two material groups, based on their deformation behaviour (see tables 6 and 7).Page 6DIN 59740 : 2004-07Table 6: Material group IMaterial Approx. density, in kg/dmAs specied in

29、name numberNi99,6 2.4060 8,9DIN 17740LC-Ni99,6 2.4061 8,9Ni99,2 2.4066 8,9LC-Ni99 2.4068 8,9LC-NiCr15Fe 2.4817 8,5 DIN 17742NiCu30Fe 2.4360 8,8DIN 17743LC-NiCu30Fe 2.4361 8,8Table 7: Material group IIMaterialApprox. density, in kg/dmAs specied inname numberNiCr22Mo7Cu 2.4619 8,3DIN 17742NiCr25FeAlY

30、2.4633 7,9NiCr29Fe 2.4642 8,2NiCr25FeAlYC 2.4647 7,9NiCr15Fe 2.4816 8,5NiCr23Fe 2.4851 8,2NiCr8020 2.4869 8,3NiCr28FeSiCe 2.4889 8,0NiCr20Ti 2.4951 8,4NiMo29Cr 2.4600 9,2DIN 17744NiCr21Mo14W 2.4602 8,7NiCr23Mo16Al 2.4605 8,6NiCr21Mo16W 2.4606 8,7NiCr26MoW 2.4608 8,2NiMo16Cr16Ti 2.4610 8,6NiMo28 2.46

31、17 9,2NiCo20Cr20MoTi 2.4650 8,4NiCr20CuMo 2.4660 8,1NiCr23Co12Mo 2.4663 8,4NiCr22Fe18Mo 2.4665 8,3NiCr19Fe19Nb5Mn3 2.4668 8,2NiCr23Mo16Cu 2.4675 8,6NiMo23Cr8Fe 2.4710 8,9NiCr22W14Mo 2.4733 9,0NiMo16Cr15W 2.4819 8,9NiCr22Mo9Nb 2.4856 8,4NiCr21Mo 2.4858 8,1Page 7DIN 59740 : 2004-07Other relevant stand

32、ardsDIN 59742 Hot rolled nickel and nickel alloy rings and circular blanks Dimensions, tolerances and material groupsDIN 59745 Cold rolled nickel and nickel alloy sheet and plate Dimensions, tolerances and material groupsDIN 59746 Cold rolled nickel and nickel alloy sheet and plate made from straightened strip Dimensions, tolerances and material groups