DIN 55473-2015 Auxiliary means of packaging - Desiccant in bag - Technical delivery conditions《辅助包装方法 包中干燥剂 交货技术条件》.pdf

《DIN 55473-2015 Auxiliary means of packaging - Desiccant in bag - Technical delivery conditions《辅助包装方法 包中干燥剂 交货技术条件》.pdf》由会员分享，可在线阅读，更多相关《DIN 55473-2015 Auxiliary means of packaging - Desiccant in bag - Technical delivery conditions《辅助包装方法 包中干燥剂 交货技术条件》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、December 2015 English price group 10No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 55.040!%XUo“2535076www.din.deDI

2、N 55473Auxiliary means of packaging Desiccant in bag Technical delivery conditions,English translation of DIN 55473:2015-12Packhilfsmittel Trockenmittelbeutel Technische Lieferbedingungen,Englische bersetzung von DIN 55473:2015-12Matriaux auxiliaires demballage Sachet dshydratant Conditions de livra

3、ison techniques,Traduction anglaise de DIN 55473:2015-12SupersedesDIN 55473:200810www.beuth.deDocument comprises 15 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.01.17 DIN 55473:2015-12 2 A comma is used as the decimal marker

4、. Contents Page Foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions 4 4 Requirements 5 4.1 Desiccants . 5 4.2 Desiccant unit 6 4.3 Desiccant bag. 6 4.4 Designation 7 5 Testing . 7 5.1 General 7 5.2 Desiccants . 7 5.3 Desiccant unit 8 5.4 Desiccant bag. 11 6 Consignment 12 6.1 Gen

5、eral 12 6.2 Group package 12 6.3 Number of desiccant bags per group package 12 6.4 Means of attachment 13 6.5 Marking . 13 7 Quality testing . 13 7.1 Visual and dimensional inspection . 13 7.2 Production testing . 14 8 Inspection . 15 8.1 General 15 8.2 Records 15 8.3 Test report . 15 DIN 55473:2015

6、-12 3 Foreword This document has been prepared by DIN-Normenausschuss Verpackungswesen (DIN Standards Committee Packaging), Working Committee NA 115-03-04 AA Trockenmittel. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall

7、 not be held responsible for identifying any or all such patent rights. Amendments This standard differs from DIN 55473:2008-10 as follows: a) a table of contents is now included; b) normative references have been updated; c) the particle size distribution is described in greater detail in 4.1.5; d)

8、 the measurement of the particle size is described in greater detail in 5.2.3; e) the heading of 5.3.1.2 has been modified; f) the test and the scope of testing has been modified in 5.4.1; g) the structure of the standard has been adapted to suit the current rules of presentation. Previous editions

9、DIN 55473: 1984-07, 1989-07, 1997-12, 2001-02, 2008-10 DIN 55473:2015-12 4 1 Scope This standard applies to adsorptive desiccants in bags which are sufficiently permeable to water vapour, for use in packaging with a low water vapour permeability. The purpose of these specifications is to provide uni

10、form criteria for the evaluation of the efficiency of desiccant bags. Desiccant bags are intended to protect packaged goods from excessive atmospheric humidity during transport and storage, in order to prevent corrosion, attack by mould, etc. 2 Normative references The following documents, in whole

11、or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN 55405, Packaging Terminology Terms an

12、d definitions DIN EN ISO 15106-3, Plastics Film and sheeting Determination of water vapour transmission rate Part 3: Electrolytic detection sensor method DIN ISO 3310-1, Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth DIN ISO 3310-2, Test sieves Technical requi

13、rements and testing Part 2: Test sieves of perforated plates BWB TL 6685-0003, Ausgabe 5, Technische Lieferbedingungen1) Packhilfsmittel Feuchtigkeits-Anzeigekarten Feuchtigkeits-Kontrollfenster gro und klein (Technical delivery conditions Humidity indicator cards used as auxiliary means of packagin

14、g Small and large inspection windows) 3 Terms and definitions For the purposes of this standard, the terms and definitions in DIN 55405 and the following apply. 3.1 desiccant bag TMB (de: Trockenmittelbeutel) auxiliary means of packaging consisting of a low-dust or dustproof wrapping material which

15、is permeable to water vapour, containing a chemically-inert, water vapour adsorbant, active desiccant 3.2 desiccant unit TME (de: Trockenmitteleinheit) given quantity of desiccant which adsorbs at least 6,0 g of water vapour at 40 % relative air humidity in equilibrium with air at (23 2) C Note 1 to

16、 entry: The number of desiccant units is the measure of the adsorptive capacity of the desiccant bag. 1)Obtainable from: Bundesamt fr Ausrstung, Informationstechnik und Nutzung der Bundeswehr (Federal Office of Bundeswehr Equipment, Information Technology and In-Service Support BAAINBw), http:/www.b

17、aainbw.de (sourced: 27.10.2015). DIN 55473:2015-12 5 3.3 group package packaging with a defined water vapour permeability for desiccant bags to prevent unintended activity loss of the desiccant (protective packaging) 3.4 manufacturer person or organization producing desiccant bags on an industrial s

18、cale or smaller, regardless of whether these bags are produced by the manufacturer himself or on his behalf, with a view to placing the bags on the market in his own name 4 Requirements 4.1 Desiccants 4.1.1 General Desiccants are characterized solely by their physical and chemical properties. Desicc

19、ants (e.g. activated clay, aluminium silicate, silica gel, alumina gel; granules or beads) shall be free of impurities and shall not deliquesce. 4.1.2 pH value of the aqueous extract The pH value of an aqueous extract from the desiccant shall neither be below 3,5 nor exceed 8,5. Testing shall be as

20、in 5.2.1. 4.1.3 Electrical conductivity of the aqueous extract The electrical conductivity in an aqueous extract of the desiccant shall not exceed 0,3SmTesting shall be as in 5.2.1. 4.1.4 Content of water-soluble substances The mass fraction of water-soluble substances in the desiccant shall not exc

21、eed 2 %. Testing shall be as in 5.2.2. 4.1.5 Particle size The particle size distribution of the desiccant shall be 100 % for particles 16 0,10 g H2O Testing shall be as in 5.3.3. 4.2.3 Volume The volume per desiccant unit shall not exceed 45 cm3. Testing shall be as in 5.3.2. 4.2.4 Mass The mass pe

22、r desiccant unit shall not exceed 39 g. Testing shall be as in 5.3.2. 4.3 Desiccant bag 4.3.1 Wrapping material The wrapping material shall be woven fabric, paper, non-woven fabric or another material sufficiently permeable to water vapour and sufficiently strong to comply with the requirements spec

23、ified in Clauses 4 and 5. Testing of the strength of the filled bag shall be as in 5.4.2. DIN 55473:2015-12 7 4.3.2 Type of bags There are two types of bags. a) Type A: low-dust No more than 10 mg of dust per desiccant unit shall migrate through the wrapping material. Testing shall be as in 5.4.1. b

24、) Type B: dustproof Regardless of the number of desiccant units in the bag, no more than 1 mg of dust shall be detectable after testing. Testing shall be as in 5.4.1. 4.3.3 Number of desiccant units (TME) per desiccant bag (TMB) The desiccant bags contain either (1/6, 1/3, 1/2, 1, 2, 4, 8, 16 or 32)

25、 desiccant units. 4.4 Designation A desiccant bag with 2 desiccant units (2 E) of the low-dust type (A) is designated as follows: Desiccant DIN 55473 2 E A 5 Testing 5.1 General The tests shall be carried out quickly in order to keep the influence of air humidity low. 5.2 Desiccants 5.2.1 pH value a

26、nd electrical conductivity of the aqueous extract 10 g of loose desiccant are refluxed in 100 ml of distilled water for 10 min, filtered after cooling and the test carried out at (20 2) C in the filtrate. 5.2.2 Content of water-soluble substances The clear filtrate obtained from the pH measurement i

27、s evaporated in an evaporating dish weighed to constant mass. After drying for 1 h at 105 C, the evaporation residue is determined gravimetrically (maximum permissible error: 5 mg). 5.2.3 Particle size For the test a screening machine is used which makes horizontal circular movements at (300 10) min

28、1 and an amplitude of 15 mm or vertical movements with an amplitude of 3 mm. A sieving medium of aperture size 6,3 mm and a sieving medium of aperture size 0,25 mm as in DIN ISO 3310-1 and DIN ISO 3310-2 with a diameter of approximately 200 mm and a lid and a receiver shall be used. 100 g of desicca

29、nt are placed in the uppermost sieve and sieved for at least 3 min using the machine. Immediately after sieving, the residue on each individual sieve and in the receiver is weighed to the nearest 0,5 g and the sieve fraction calculated as a mass fraction. The sum of the individual desiccant masses i

30、s determined after sieving and taken as the overall mass. DIN 55473:2015-12 8 5.3 Desiccant unit 5.3.1 Adsorptive capacity 5.3.1.1 Dynamic isothermal procedure Figure 1 shows the set-up of the apparatus. The head for the saturation solution bottles with tight-fitting ground-glass stopper is equipped

31、 with an inlet guide with bubble distributor and discharge tube. The bubble distributor should be between 75 mm and 25 mm below the liquid level when there is 1 l of solution in the bottle. Each of the 6 saturation bottles is to be filled with 1 l of sulfuric acid solution (H2SO4) of the same concen

32、tration, as specified in Table 2. The receiver should be a normal adsorption vessel with a suitable closure. The ambient temperature is to be kept at (23 2) C. An adsorption trap containing at least 500 cm3 of desiccant should be placed upstream of the saturation bottles in order to adsorb impuritie

33、s from the incoming air. Table 2 Relative air humidity at (23 2) C Solution Mass fraction Density of the solution at 20 C % % g/cm3 0,005 40 H2SO447,8 1,374 A representative composite sample of about 10 g of desiccant is weighed to the nearest 5 mg into a tared adsorption vessel. The desiccant is to

34、 be introduced into the vessel as quickly as possible. Then the adsorption vessel containing the desiccant is to be connected to the apparatus and the stream of air regulated to (4 0,5) l/min. The maximum pressure above the atmospheric shown on the pressure gauge shall not exceed 40 mbar. During the

35、 test, the adsorption vessel is periodically removed from the apparatus and the valve closed. The adsorption vessel is to be weighed until two weighings separated by 1 h reveal a maximum difference of 10 mg. The adsorptive capacity of the sample is m. DIN 55473:2015-12 9 Key 1 Desiccant tower with d

36、esiccant 2 Valve to control the rate of air flow 3 U-tube pressure gauge 4 Flow meter 5 Vessel with desiccant 6 Trap with glass wool 7 Saturation bottles 8 Precleaning with glass wool Figure 1 Schematic arrangement of apparatus 5.3.1.2 Procedure using a controlled-atmosphere chamber As an alternativ

37、e to the dynamic isothermal procedure as specified in 5.3.1.1, commercially available controlled-atmosphere chambers, capable of being calibrated, may be used. Over the whole test duration, the humidity shall be kept at 2 % relative air humidity and the temperature at 1 K. 5.3.1.3 Calculation The ad

38、sorptive capacity of a desiccant unit, AF, in the as-delivered condition at 40 % relative air humidity is calculated using Equation (1): F=mBW(1) where AFis the adsorptive capacity; mis the increase in mass, in g; mBis the filling mass of the bag, in g; mwis the initial mass of the desiccant, in g;

39、n is the number of given units in the bag. DIN 55473:2015-12 10 5.3.2 Volume and mass A 100 ml measuring cylinder shall be weighed to the nearest 0,1 g. The measuring cylinder shall be filled with approximately 100 cm3of desiccant, weighed once more and then tapped on a resilient base until the volu

40、me remains constant between two readings. The volume of the desiccant unit is calculated using Equation (2): E=BAW(2) where VEis the volume of the desiccant unit, in cm3; mBis the filling mass of the bag, in g; VAis the volume of the desiccant weighed in, in cm3; n is the number of given desiccant u

41、nits in the bag; mwis the initial mass of the desiccant, in g. The mass of the desiccant unit mEis calculated using Equation (3): E=B(3) where mEis the mass of the desiccant unit, in g; mBis the filling mass of the bag, in g; n is the number of given desiccant units in the bag. 5.3.3 Rate of adsorpt

42、ion 5.3.3.1 Test set-up The test set-up corresponds to that specified in 5.3.1.1 with the exception of the adsorption vessel. The vessel for receiving the bag shall be of a suitable size and have a sufficiently wide mouth, e.g. a desiccator (5,0 l minimum nominal capacity up to 15,0 l maximum nomina

43、l capacity). As an alternative to the test set-up as specified in 5.3.1.1, commercially available controlled-atmosphere test chambers, capable of being calibrated, may be used to generate an air stream of 40 % relative air humidity. 5.3.3.2 Procedure The bag weighed with the desiccant is, as shown i

44、n Figure 2, inserted into the vessel so that the air stream introduced at (4 0,5) l/min and 40 % relative air humidity at (23 2) C can brush evenly over its surface. After 7 h, the bag is weighed once more. The increase in mass of the bag with the desiccant is m. DIN 55473:2015-12 11 Key 1 Outlet ai

45、r 2 Inlet air 3 Air diffuser tube 4 Sieving medium Figure 2 Schematic description Rate of adsorption 5.3.3.3 Calculation The rate of adsorption per desiccant unit is calculated using Equation (4): G=m(4) where AGis the rate of adsorption, in g/TME; mis the increase in mass, in g/7 h; n is the number

46、 of given desiccant units (TME) in the bag. 5.4 Desiccant bag 5.4.1 Dust permeability The desiccant bags are dropped flat on alternate sides 20 times from a height of 50 cm into a vessel. The vessel shall meet the following requirements: material: metal or ceramics (smooth and antistatic) dimensions

47、: 50 cm 50 cm 50 cm (L B H) colour: black (inside) DIN 55473:2015-12 12 The dust escaping from the bags shall be transferred to a weighing vessel using a brush (with natural hair). No dust shall be lost in the process. The dust shall then be weighed. Calculation: SE=S(5) where SEis the mass of escap

48、ing dust per desiccant unit, in mg per TME; Sis the weighed total mass of escaping dust, in mg; n is the number of desiccant units in the bag. 5.4.2 Strength of the bag If the desiccant bags ( 4 desiccant units) with desiccant are dropped flat on alternate sides 15 times from a height of 3 m onto a

49、smooth, non-deformable, non-resilient surface (e.g. granite, marble, steel), they shall not burst on impact or be otherwise damaged in a way that allows desiccant to escape. 6 Consignment 6.1 General Desiccant bags are to be packed in a tightly sealed group package with a humidity indicator and a suitable shipping package (e.g. boxes, plastic or steel drums). 6.2 Group