DIN 471-2011 Retaining rings for shafts - Normal type and heavy type《轴用挡圈 标准型和重型》.pdf
《DIN 471-2011 Retaining rings for shafts - Normal type and heavy type《轴用挡圈 标准型和重型》.pdf》由会员分享,可在线阅读,更多相关《DIN 471-2011 Retaining rings for shafts - Normal type and heavy type《轴用挡圈 标准型和重型》.pdf(24页珍藏版)》请在麦多课文档分享上搜索。
1、April 2011 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS
2、21.060.60; 21.120.10!$t+4“1810817www.din.deDDIN 471Retaining rings for shafts Normal type and heavy typeEnglish translation of DIN 471:2011-04Sicherungsringe (Halteringe) fr Wellen Regelausfhrung und schwere AusfhrungEnglische bersetzung von DIN 471:2011-04Anneaux darrt pour arbres Type standard et
3、type robusteTraduction anglaise de DIN 471:2011-04SupersedesDIN 471:1981-09www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 24 pages10.11 DIN 471:2011-04 A comma is used as the decimal marker. Contents Page Foreword. 3 1 Scope 4 2 Normat
4、ive references 4 3 Symbols . 5 4 Dimensions and design details 6 5 Material. 16 6 Finish 16 7 Testing 17 7.1 Testing the material. 17 7.2 Bend and fracture test 17 7.3 Testing the deformation 17 7.3.1 Testing the conical deformation 17 7.3.2 Testing the spiral flatness 18 7.4 Testing the function (p
5、ermanent set and grip test) 18 7.5 Acceptance inspection . 18 8 Load bearing capacity. 19 8.1 General . 19 8.2 Load bearing capacity of groove FN. 19 8.3 Load bearing capacity of retaining ring FR19 9 Detaching speed 20 10 Design of the groove. 21 10.1 Groove diameter d2. 21 10.2 Groove width m 21 1
6、0.3 Design of the groove base 22 11 Assembly . 23 12 Designation 24 2 DIN 471:2011-04 Foreword This standard has been prepared by Working Committee NA 067-00-09 AA Verbindungselemente ohne Gewinde of the Normenausschuss Mechanische Verbindungselemente (Fasteners Standards Committee). Attention is dr
7、awn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. Amendments This standard differs from DIN 471:1981-09 as follows: a) normative references have been updated; b) the
8、specifications for load bearing capacity, detaching speed and assembly have been revised; c) the tolerances on radial run-out have been deleted from Figure 2 (formerly Figure 3); d) in Clause 10, Figure 11 (formerly Figure 14) “Taper assembly” has been revised; e) Figure 10 “Design of groove base” h
9、as been included in 10.3; f) examples of designation for retaining rings with corrosion protection have been included; g) the standard has been editorially revised. Previous editions DIN 471: 1941-12, 1942-11, 1952-01, 1954-01, 1981-09 DIN 471 and DIN 472 Supplement 1: 1945-01, 1954x-03 DIN 471-1: 1
10、965-03 DIN 471-2: 1965-03 DIN 995: 1970-01 3 DIN 471:2011-04 1 Scope This standard specifies requirements for retaining rings for shafts and lays down design details for the grooves into which such rings are fitted. NOTE Retaining rings are used to hold components or assemblies (e.g. rolling bearing
11、s) on shafts and are suitable for the transmission of axial forces. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced doc
12、ument (including any amendments) applies. DIN 988, Shim rings and supporting rings DIN 5254, Pliers for retaining rings for shafts DIN 50938, Black oxide coatings on iron or steel Requirements and test methods DIN EN 10132-4, Cold-rolled narrow steel strip for heat-treatment Technical delivery condi
13、tions Part 4: Spring steels and other applications DIN EN 12476, Phosphate conversion coatings of metals Method of specifying requirements DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 6507-1, Metallic materials Vickers hardness test Pa
14、rt 1: Test method DIN EN ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) DIN EN ISO 9227, Corrosion tests in artificial atmospheres Salt spray tests DIN EN ISO 18265, Metallic materials Conversion of hardness values DIN ISO 2859-1, S
15、ampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection 4 DIN 471:2011-04 3 Symbols a radial width of the lug b radial width of retaining ring opposite the aperture c distance between measuring plates for testing sp
16、iral flatness d1shaft diameter d2groove diameter d3internal diameter of retaining ring in the unstressed state d4maximum centre line diameter of external clearance during assembly, to be calculated from: d4= d1+ 2,1 a d5diameter of the assembly holes E modulus of elasticity F force acting on the ret
17、aining ring when testing conical deformation FNload bearing capacity of groove at a yield point of the grooved material of 200 MPa (see 8.2) FRload bearing capacity of retaining ring with sharp-edged abutment of a machine component (see 8.3)FRgload bearing capacity of retaining ring for abutment wit
18、h edge distance g (see 8.3) g edge distance of the machine component abutting the retaining ring h distance between the plates when testing conical deformation m groove width n edge margin nabldetaching speed of the retaining ring (see Clause 9) ReLyield point r curvature in the groove base or test
19、jaws s thickness of retaining ring t groove depth with nominal sizes of d1and d25 DIN 471:2011-04 4 Dimensions and design details The designs shown in Figure 1 are for illustrative purposes only; however, the dimensions of retaining rings and grooves shall be as specified in Tables 1 and 2. The tole
20、rances specified relate to retaining rings in their uncoated condition. Unstressed Shape of ring at manufacturers discretion a) b) Detail X d1 9 mm 9 mm d1 300 mm d1 170 mm at manufacturers discretion Key 1 External clearance Figure 1 Dimensions of retaining ring (notation) 6 DIN 471:2011-04 7 Figur
21、e 2 Example of installation Values for peak-to-valley height for groove base and loaded edge shall be specified in each case. The design of the groove base shall be as specified in 10.3. DIN 471:2011-04 8 Table 1 Normal type Dimensions in millimetres Ring Groove Supplementary datadShaft diameter d1s
22、 d3a ba d5Mass per 1 000 unitsin kg d2b mct n4d4FNFRg FRgnablNominal size perm.dev. perm. dev. max. min. perm.dev. H13 min. kN kN kN min1Nominal size of pliers as in DIN 5254 3 0,4 2,7 1,9 0,8 1,0 0,017 2,8 0 0,04 0,5 0,10 0,3 7,0 0,15 0,47 0,5 0,27 360 000 4 0,4 3,7 2,2 0,9 1,0 0,022 3,8 0,5 0,10 0
23、,3 8,6 0,20 0,50 0,5 0,30 211 000 5 0,6 4,7 2,5 1,1 1,0 0,066 4,8 0,7 0,10 0,3 10,3 0,26 1,00 0,5 0,80 154 000 6 0,7 5,6 +0,04 0,15 2,7 1,3 1,2 0,084 5,7 0 0,05 0,8 0,15 0,5 11,7 0,46 1,45 0,5 0,90 114 000 7 0,8 6,5 3,1 1,4 1,2 0,121 6,7 0,9 0,15 0,5 13,5 0,54 2,60 0,5 1,40 121 000 8 0,8 0 0,05 7,4
24、3,2 1,5 1,2 0,158 7,6 0 0,06 0,9 0,20 0,6 14,7 0,81 3,00 0,5 2,00 96 000 9 1,0 8,4 +0,06 0,18 3,3 1,7 1,2 0,300 8,6 1,1 0,20 0,6 16,0 0,92 3,50 0,5 2,40 85 000 3 10 1,0 9,3 3,3 1,8 1,5 0,340 9,6 1,1 0,20 0,6 17,0 1,01 4,00 1,0 2,40 84 000 3; 10 11 1,0 10,2 3,3 1,8 1,5 0,410 10,5 1,1 0,25 0,8 18,0 1,
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DIN4712011RETAININGRINGSFORSHAFTSNORMALTYPEANDHEAVYTYPE 轴用挡圈 标准型 重型 PDF
链接地址:http://www.mydoc123.com/p-657746.html