DIN 3965-4-1986 Tolerancing of bevel gears tolerances for shaft angle errors and axes intersection point deviations《伞齿轮啮合公差 第4部分 轴线夹角误差及轴线交叉点偏差用公差》.pdf

《DIN 3965-4-1986 Tolerancing of bevel gears tolerances for shaft angle errors and axes intersection point deviations《伞齿轮啮合公差 第4部分 轴线夹角误差及轴线交叉点偏差用公差》.pdf》由会员分享，可在线阅读，更多相关《DIN 3965-4-1986 Tolerancing of bevel gears tolerances for shaft angle errors and axes intersection point deviations《伞齿轮啮合公差 第4部分 轴线夹角误差及轴线交叉点偏差用公差》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、UDC 621 -833.2 : 621.753.1 DEUTSCHE NORM August 1986 Tolerancing of bevel gears Tolerances for shaft angle errors and axes intersection point deviations blN 3965 Part 4 Toleranzen fr Kegelradverzahnungen; Toleranzen fr Achsenwinkelabweichungen und Achsenschnittpunktabweichungen Supersedes September

2、1981 edition. The accuracy of the bevel gear transmission housing is a major factor influencing the working load limit and running quality of the gearing. For the deviations of the housing parameters (position of gear axes), 12 accuracy grades for the axial position have been specified. These accura

3、cy grades are not expected to correspond with the tolerance classes specified for bevel gears. The permissible axes intersection point deviations (axial offset deviations) are also a function of the diameter of the larger gear of the pair. Backlash has to be taken into account when specifying the to

4、lerances. Deformation of the housing under load may greatly modify the deviations. 1 Scope and field of application This standard specifies values for straight, skew and spiral bevel gears with and without axial offset, and with reference diameters up to 2500 mm. The tolerances for the parameters sp

5、ecified in this standard are defined in DIN 3971, the values given in tables 1 and 2 applying to the gear pair. See also DIN 3965 Part 1. Continued on pages 2 and 3 Beuth Verlag GmbH, Berlin, has the exclusive right of sale for German Standards (DIN-Normen). DIN 3965 Part 4 Eng/. Price group 5 Sales

6、 No. 0105 06.87 Page 2 DIN 3965 Part 4 2 Tolerances Accuracy grade for axial position h Gear axis 2 (theoretical 1 2 3 4 5 6 7 8 9 10 11 12 - - - i16 *20 I25 i32 I40 150 t63 180 1100 position = actual( 1 / position) Accuracy grade for axial position Upto 50 Over 50 s up to 125 Over 125 upto 280 3 m

7、E Over 280 5 .E upto 560 z- Over 560 h up to 1000 E m Over 1000 z up to 1600 Over 1600 up to 2500 0 En .c O L- Gear axis 1 (theoretical position) 2 3 4 5 6 7 8 9 10 11 12 - - - I 6 f 8 110 112 116 120 25 I 32 f 40 - - - - + 8 +IO i12 I16 f20 125 f 32f 4Of 50 - - - it10 112 516 I20 I25 132 I 40+50*63

8、 - - i12 116 I20 I25 I32 i40 i 50 i 63 f 80 - - - - k16 120 I25 I32 I40 150 63I 80I100 - - - i20 +25 I32 I40 I50 I63 f 80I100+125 - - - +25 I32 I40 f50 +63 +80 +100f125+160 Gear axis 1 (actual position) Figure 1. Deviations of position of bevel gear axes Table 2. Permissible axes intersection point

9、deviations axial, fa, in pm D IN 3965 Part 4 Page 3 Standards referred to DIN 3965 Part 1 Tolerancing of bevel gears; basic concepts DIN 3971 Terminology and parameters for bevel gears and bevel gear pairs Previous editions DIN 3965 Part 4: 09.81. Amendments The following amendments have been made i

10、n comparison with the September 1981 edition. a) The status of the standard is no longer that of a preliminary standard. b) The standard has been editorially revised. Explanatory notes The housing tolerances given in this standard have been specified to a fineness which cannot be technically realize

11、d at present, but which is likely to represent the fineness possible in future. The concepts of axes intersection point, axial offset and shaft angle (see DIN 868) and of axes intersection point deviation and shaft angle error (see DIN 3971) have been established as follows. Axial offset The axial o

12、ffset, a, of a hypoid gear pair is the distance between the two non-intersecting gear axes. For a bevel gear pair a is equal to zero. Shaft angle The shaft angle, E, of a bevel gear pair is that angle between the two axes that faces the tooth engagement. The shaft angle, ,Y, of a hypoid gear pair is

13、 that angle between the non-intersecting gear axes that faces the tooth engage- ment. Shaft angle error The shaft angle error, fc, is the difference between the shaft angle of the two gear shafts in their actual positions and the theoretical value of this angle. Axes intedon point deviation The axes

14、 intersection point deviation,f, of a bevel gear pair is the distance between the two non-intersecting gear axes in their actual positions. The axes intersection point deviation, fa, of a hypoid gear pair is the difference between the distance separating the two non-intersecting gear axes in their a

15、ctual positions compared with the theoretical distance. The permissible values of fa given in this standard correspond to the axial position tolerances of cylindrical gear trans- missions as specified in DIN 3964, but the fa values are shifted by one accuracy grade towards larger deviations, and reduced by half. The tolerance system proposed for bevel gears is also intended to serve as a basis for international discussion. International Patent Classification F 16 H 55/08 F 16 H 55/17