DIN 2250-1-2008 Geometrical product specifications (GPS) - GO ring gauges and setting ring gauges - Part 1 From 1 mm up to 315 mm nominal diameter《产品几何量技术规范(GPS) 过端环规和定位环规 第1部分 1mm.pdf

《DIN 2250-1-2008 Geometrical product specifications (GPS) - GO ring gauges and setting ring gauges - Part 1 From 1 mm up to 315 mm nominal diameter《产品几何量技术规范(GPS) 过端环规和定位环规 第1部分 1mm.pdf》由会员分享，可在线阅读，更多相关《DIN 2250-1-2008 Geometrical product specifications (GPS) - GO ring gauges and setting ring gauges - Part 1 From 1 mm up to 315 mm nominal diameter《产品几何量技术规范(GPS) 过端环规和定位环规 第1部分 1mm.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、October 2008DEUTSCHE NORM Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DI

2、N-Normen).ICS 17.040.30!$T6“1499719www.din.deDDIN 2250-1Geometrical product specifications (GPS) GO ring gauges and setting ring gauges Part 1: From 1 mm up to 315 mm nominal diameterGeometrische Produktspezifikation (GPS) Gutlehrringe und Einstellringe Teil 1: Von 1 mm bis 315 mm NenndurchmesserSup

3、ersedesDIN 2250-1:1989-11www.beuth.deDocument comprises 11 pagesIn case of doubt, the German-language original should be consulted as the authoritative text.DIN 2250-1:2008-10 2 Foreword This standard has been prepared by Subcommittee NA 152-03-02-07 UA Eindimensionale Lngenprftechnik of Section 3 G

4、eometrische Produktspezifikation und -prfung, with the participation of Technical Committee NA 152-02-03 AA Gewindeprfung, both of the Normenausschuss Technische Grundlagen (NATG) (Fundamental Technical Standards Committee). The DIN 2250 Geometrical product specifications (GPS) GO ring gauges and se

5、tting ring gauges series of standards comprises the following: Part 1: From 1 mm to 315 mm nominal diameter Part 2: From 1 mm to 315 mm nominal diameter for precision engineering Amendments This standard differs from DIN 2250-1:1989-11 as follows: a) The introductory element “Geometrical product spe

6、cifications (GPS)” has been added to the title. b) “R setting rings” for adjustable reamers are now specified. c) Subclause “Requirements for R setting rings” has been added. d) The tolerance class for bore d1for C setting rings has been changed from “JS3” to “JS4”. e) The run-out tolerance has been

7、 replaced by the squareness tolerance. f) The roughness parameter “Rz” has been changed to “Rzmax” in accordance with DIN EN ISO 1302. g) The standard has been editorially revised. Previous editions DIN 237: 1924-11, 1928-07 DIN 369: 1925-04, 1928-07 DIN 451: 1940-06 DIN 2250: 1951-10 DIN 2250-1: 19

8、77-09, 1983-01, 1989-11 DIN 2250-1:2008-10 3 1 Scope This standard applies to GO ring gauges for general purposes (G), setting rings for pneumatic length measuring instruments (B), setting rings for length measuring instruments (C), and setting rings for adjustable reamers (R). 2 Normative reference

9、s The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN 82, Knurls DIN 2239, Geometrical product sp

10、ecifications (GPS) Gauges in dimensional metrology Requirements and testing DIN 2259, Geometrical product specifications (GPS) Gauges for cylindrical fits and fits of plan surfaces Survey, lettering, marking DIN 2279, Geometrical product specifications (GPS) Gauges for ISO metric screw threads Gaugi

11、ng of internal and external threads Survey, lettering, marking, application DIN 7150-2, Geometrical product specifications (GPS) System of limits and fits Part 2: Limit gauges and gauging for plain cylindrical workpieces DIN 7163, Workshop gap gauges and check gauges for ISO fit sizes from 1 to 500

12、mm nominal diameters Gauge dimensions and manufacturing tolerances DIN EN ISO 1101, Geometrical product specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-out DIN ISO 286-1, ISO system of limits and fits Bases of tolerances, deviations and fits DIN ISO 150

13、2, ISO general purpose metric screw threads Gauges and gauging 3 Terms and definitions For the purposes of this document, the terms defined in DIN EN ISO 1101 and DIN ISO 286-1 apply. 4 Dimensions, designation 4.1 Dimensions Dimensions shall be as in Figures 1 and 2 and Tables 1 and 2. G GO ring gau

14、ge for general purposes B setting ring for pneumatic length measuring instruments C setting ring for general purposes R setting ring for adjustable reamers DIN 2250-1:2008-10 4 GO ring gauges and setting rings of 1 mm up to 100 mm nominal diameter Key 1 Area for marking 2 RGE 0,5 to 1 knurl as in DI

15、N 82 Figure 1 GO ring gauges and setting rings of 1 mm up to 100 mm nominal diameter (notation) GO ring gauges and setting rings of over 100 mm up to 315 mm nominal diameter Key 1 Area for marking 2 Undercut optional aWith or without RGE 0,5 to 1 knurl as in DIN 82, at manufacturers discretion Figur

16、e 2 GO ring gauges and setting rings of over 100 mm up to 315 mm nominal diameter (notation) DIN 2250-1:2008-10 5 Table 1 General dimensions for GO gauges and setting rings of 1 mm up to 100 mm nominal diameter Dimensions in millimetres Nominal diameter d1d2b1 for G, B and R C from 1 up to 2,5 22 6

17、4 over 2,5 up to 5 22 10 5 over 5 up to 10 32 12 8 over 10 up to 15 38 14 10 over 15 up to 20 45 16 12 over 20 up to 25 53 18 14 over 25 up to 32 63 20 16 over 32 up to 40 71 24 18 over 40 up to 50 85 over 50 up to 60 100 20 over 60 up to 70 112 over 70 up to 80 125 over 80 up to 90 140 over 90 up t

18、o 100 160 32 24 Table 2 General dimensions for GO gauges and setting rings of 100 mm up to 315 mm nominal diameter Dimensions in millimetres Nominal diameter d1d2d3b1for b2G, B and R C over 100 up to 110 170 132 14 over 110 up to 120 180 140 over 120 up to 130 190 150 16 over 130 up to 140 200 160 o

19、ver 140 up to 150 212 170 18 over 150 up to 160 224 180 36 28 over 160 up to 170 236 190 over 170 up to 180 250 200 20 over 180 up to 190 265 212 40 over 190 up to 200 280 224 over 200 up to 212 300 236 22 over 212 up to 224 315 250 45 32 over 224 up to 236 335 265 25 over 236 up to 250 355 280 over

20、 250 up to 265 375 300 50 over 265 up to 280 400 315 28 over 280 up to 300 425 335 over 300 up to 315 450 355 56 36 32 DIN 2250-1:2008-10 6 4.2 Designation Designation of a GO ring gauge (G) for checking toleranced dimension 25h9: Ring gauge DIN 2250 G 25h9 Designation of a GO ring gauge (G) for che

21、cking the major diameter of an M80 4 external thread made to tolerance class 6g: Ring gauge DIN 2250 G M80 4 6g Designation of a setting ring for calibrating pneumatic length measuring instruments (B) to a nominal dimension of 16 mm: Setting ring DIN 2250 B 16 Designation of a setting ring for calib

22、rating length measuring instruments (C) to a nominal dimension of 8 mm: Setting ring DIN 2250 C 8 Designation of a setting ring for calibrating adjustable reamers (R) to a nominal dimension of 16 mm, tolerance class K7: Setting ring DIN 2250 R 16K7 5 Requirements 5.1 General requirements Technical d

23、elivery conditions shall be as in DIN 2239. Lettering and marking shall be as in DIN 2259 and DIN 2279. Squareness tolerance t of the blank face: Numerical values of the IT9 series as in DIN ISO 286-1 relative to d1. Protruding edges resulting from the manufacturing process shall not be deeper than

24、as specified in Table 3 on either side. Table 3 Depth of protruding edges for b1of 4 mm up to 56 mm Dimensions in millimetres b1Depth of protruding edges from 4 up to 6 0,5 over 6 up to 10 0,8 over 10 up to 18 1 over 18 up to 36 1,5 over 36 up to 56 2 DIN 2250-1:2008-10 7 5.2 Requirements for G GO r

25、ing gauges Gauge dimensions for dimensions given with ISO tolerance symbols shall be as in DIN 7163. Gauge dimensions for dimensions given with numerical tolerances shall be as in DIN 7150-2. Gauge dimensions for the major diameter of external threads shall be as in DIN ISO 1502. 5.3 Requirements fo

26、r B and C setting rings Tolerance class for bore d1: JS4 Surface roughness parameter Rzmax for bore d1: 0,4 m Cylindricity tolerance for bore d1: up to 150 mm nominal diameter: 0,1 numerical value of IT4 series as in DIN ISO 286-1, over 150 mm nominal diameter: subject to agreement between manufactu

27、rer and user. EXAMPLE Tolerances for setting rings in 50 mm to 80 mm nominal diameter range: Dimensional tolerance for bore d1: JS4 = 4 m Cylindricity tolerance for bore d1: 0,1 IT4 = 0,8 m 5.4 Requirements for R setting rings Tolerance class for bore d1: see Table 4 Surface roughness parameter Rzma

28、x for bore d1: 0,4 m Cylindricity tolerance for bore d1: up to 150 mm nominal diameter 0,1 numerical value of IT4 series as in DIN ISO 286-1, over 150 mm nominal diameter subject to agreement between manufacturer and user. The nominal size of the bore, d1, of setting rings for adjustable reamers sha

29、ll be determined by adding 2/3 of the workpiece bore tolerance to the minimum workpiece bore size. To obtain a logical series, some tolerances within the nominal diameter range of 1 mm to 10 mm were slightly modified. The specification laid down in the first sentence of this paragraph shall be taken

30、 into consideration when calculating the tolerance for bore d1of setting rings in other tolerance classes than those given in Table 4 or for workpiece bores that are given with numerical tolerances. DIN 2250-1:2008-10 8 Table 4 Tolerances for bores of R setting rings for adjustable reamers, given fo

31、r various nominal diameters and tolerance classes Dimensions in micrometres Tolerance class Nominal diameter d1 mm F6 G6 H6 J6 K6 M6 N6 P6 R6 S6 T6 U6 Tolerance for d11 up to 3 +12 +8 +5 +1 2 6 9 12 15 18 over 3 up to 6 +15 +9 +5 +1 4 8 12 15 19 23 over 6 up to 10 +19 +11 +6 +2 1 6 10 15 19 23 28 ov

32、er 10 up to 14 over 14 up to 18 +23 +13 +7 +2 2 8 13 19 24 29 34 1,5 over 18 up to 24 41 over 24 up to 30 +29 +16 +9 +4 2 8 15 22 28 35 41 over 30 up to 40 48 over 40 up to 50 +36 +20 +11 +5 2 9 17 26 34 43 54 2 over 50 up to 65 41 52 66 over 65 up to 80 +43 +23 +13 +7 2 11 20 32 43 59 2,5 over 80 u

33、p to 100 +51 +27 +15 +9 3 13 23 37 51 71 3 DIN 2250-1:2008-10 9 Table 4 Tolerances for bores of R setting rings for adjustable reamers, given for various nominal diameters and tolerance classes (continued) Dimensions in micrometres Tolerance class Nominal diameter d1 mm E7 F7 G7 H7 J7 K7 M7 N7 P7 R7

34、 S7 T7 U7 X7 Z7 Tolerance for d11 up to 3 +20 +13 +9 +6 0 3 7 10 13 16 19 23 29 over 3 up to 6 +28 +18 +12 +8 +1 4 8 12 15 19 23 28 35 over 6 up to 10 +35 +23 +15 +10 +3 0 5 9 14 18 22 27 33 41 over 10 up to 14 39 49 over 14 up to 18 +44 +28 +18 +12 +4 0 6 11 17 22 27 32 44 59 1,5 over 18 up to 24 4

35、0 63 72 over 24 up to 30 +54 +34 +21 +14 +5 1 7 14 21 27 34 40 47 63 87 over 30 up to 40 47 59 79 111 over 40 up to 50 +67 +42 +26 +17 +6 1 8 16 25 33 42 53 69 96 2 over 50 up to 65 40 52 65 86 121 over 65 up to 80 +80 +50 +30 +20 +8 1 10 19 31 42 58 74 101 2,5 over 80 up to 100 +95 +59 +35 +23 +10

36、2 12 22 36 50 70 90 123 3 DIN 2250-1:2008-10 10 Table 4 Tolerances for bores of R setting rings for adjustable reamers, given for various nominal diameters and tolerance classes (continued) Dimensions in micrometres Tolerance class Nominal diameterd1 mm B8 C8 D8 E8 F8 H8 J8 K8 M8 N8 A9 B9 C9 D9 E9 F

37、9 H9 Tolerance for d11 up to 3 +149 +69 +29 +23 +16 +9 +2 6 +287 +157 +77 +37 +31 +24 +17over 3 up to 6 +152 +82 +42 +32 +22 +12 +3 8 +290 +160 +90 +50 +40 +30 +20over 6 up to 10 +165 +95 +55 +40 +28 +15 +5 1 6 10 +304 +174 +104 +64 +49 +37 +242 over 10 up to 18 +168 +113 +68 +50 +34 +18 +6 12 +319

38、+179 +124 +79 +61 +45 +29 2,5 over 18 up to 30 +182 +132 +87 +62 +42 +22 +9 1 7 14 +335 +195 +145 +100 +75 +55 +35 3 over 30 up to 40 +196 +146 +351 +211 +161over 40 up to 50 +206 +156 +106 +76 +51 +26 +11 1 8 16 +361 +221 +171+121 +91 +41 3,5 over 50 up to 65 +221 +171 +389 +239 +189over 65 up to 8

39、0 +231 +181 +131 +91 +61 +31 +13 1 10 19 +409 +249 +199+149 +109 +49 4 over 80 up to 100 +256 +206 +156 +108 +72 +36 +16 2 12 22 +438 +278 +228 +178 +130 +58 5 DIN 2250-1:2008-10 11 Bibliography DIN EN ISO 1302, Geometrical Product Specifications (GPS) Indication of surface texture in technical prod

40、uct documentation (ISO 1302:2002) DIN EN ISO 14253-1, Geometrical product specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 1: Decision rules for proving conformance or non-conformance with specifications (ISO 14253-1:1998) DIN ISO 13715, Technical drawings Edges of undefined shape Vocabulary and indication on drawings