CSA ASSE 1016-2011 Performance requirements for automatic compensating valves for individual showers and tub shower combinations (First Edition Update No 1 May 2012 Update No 2 Oct.pdf

《CSA ASSE 1016-2011 Performance requirements for automatic compensating valves for individual showers and tub shower combinations (First Edition Update No 1 May 2012 Update No 2 Oct.pdf》由会员分享，可在线阅读，更多相关《CSA ASSE 1016-2011 Performance requirements for automatic compensating valves for individual showers and tub shower combinations (First Edition Update No 1 May 2012 Update No 2 Oct.pdf（58页珍藏版）》请在麦多课文档分享上搜索。

1、ASSE 1016-2011/ASME A112.1016-2011/CSA B125.16-11Performance requirements for automatic compensating valves for individual showers and tub/shower combinationsLegal Notice for Harmonized StandardJointly Developed by ASME, ASSE, and CSAIntellectual property rights and ownershipAs between The American

2、Society of Mechanical Engineers (ASME), American Society of Sanitary Engineering (”ASSE”), and Canadian Standards Association (CSA) (collectively ASME, ASSE, and CSA) and the users of this document (whether it be in printed or electronic form), ASME, ASSE, and CSA are the joint owners of all works c

3、ontained herein that are protected by copyright, all trade-marks (except as otherwise noted to the contrary), and all inventions and trade secrets that may be contained in this document, whether or not such inventions and trade secrets are protected by patents and applications for patents. The unaut

4、horized use, modification, copying, or disclosure of this document may violate laws that protect the intellectual property of ASME, ASSE, and CSA and may give rise to a right in ASME, ASSE, and CSA to seek legal redress for such use, modification, copying, or disclosure. ASME, ASSE, and CSA reserve

5、all intellectual property rights in this document.Disclaimer and exclusion of liabilityThis document is provided without any representations, warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties or conditions concerning this documents fitness f

6、or a particular purpose or use, its merchantability, or its non-infringement of any third partys intellectual property rights. ASME, ASSE, and CSA do not warrant the accuracy, completeness, or currency of any of the information published in this document. ASME, ASSE, and CSA make no representations

7、or warranties regarding this documents compliance with any applicable statute, rule, or regulation.IN NO EVENT SHALL ASME, ASSE, and CSA, THEIR RESPECTIVE VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR IN

8、CIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTH

9、ER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF ASME OR CSA HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, ASME, ASSE, and CSA are not undertaki

10、ng to render professional or other services for or on behalf of any person or entity or to perform any duty owed by any person or entity to another person or entity. The information in this document is directed to those who have the appropriate degree of experience to use and apply its contents, and

11、 ASME, ASSE, and CSA accept no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained in this document. ASME, ASSE, and CSA have no power, nor do they undertake, to enforce compliance with the contents of the standards or other documents they jo

12、intly publish. Authorized use of this documentThis document is being provided by ASME, ASSE, and CSA for informational and non-commercial use only. The user of this document is authorized to do only the following:If this document is in electronic form:. load this document onto a computer for the sol

13、e purpose of reviewing it;. search and browse this document; and. print this document if it is in PDF format.Limited copies of this document in print or paper form may be distributed only to persons who are authorized by ASME, ASSE, and CSA to have such copies, and only if this Legal Notice appears

14、on each such copy.In addition, users may not and may not permit others to. alter this document in any way or remove this Legal Notice from the attached standard;. sell this document without authorization from ASME, ASSE, and CSA; or. make an electronic copy of this document.If you do not agree with

15、any of the terms and conditions contained in this Legal Notice, you may not load or use this document or make any copies of the contents hereof, and if you do make such copies, you are required to destroy them immediately. Use of this document constitutes your acceptance of the terms and conditions

16、of this Legal Notice.Update No. 2ASSE 1016-2011/ASME A112.1016-2011/CSA B125.16-11October 2013Note: For information about the Standards Update Service, go to shop.csa.ca or e-mail techsupportcsagroup.org.Title: Performance requirements for automatic compensating valves for individual showers and tub

17、/shower combinations originally published October 2011The following revisions have been formally approved and are marked by the symbol delta () in the margin on the attached replacement pages:Revised Clauses 4.2.2.2, 4.6.3, 4.8.2, 4.9.2, and 4.9.3New NoneDeleted None Update your copy by inserting th

18、ese revised pages.Keep the pages you remove for reference.J1851QM2ASME The American Society of Sanitary Engineering The American Society of Mechanical Engineers 2013 CSA GroupPerformance requirements for automatic compensating valves for individual showers and tub/shower combinationsOctober 2013Sect

19、ion III3 Design and general requirements3.1 Types of devices3.1.1 The types of devices covered by this Standard and the type-specific requirements that they shall meet are(a) Type P, Section 4.6.7;(b) Type T, Section 4.6.8; and(c) Type T/P, Section 4.6.9.3.1.2 Devices covered by this Standard shall

20、comply with all the applicable requirements of this Standard and also comply with the applicable requirements of ASME A112.18.1/CSA B125.1.3.2 Accessible designsDevices intended for use in accessible designs shall comply with the requirements in Clause 4.6 of ASME A112.18.1/CSA B125.1.3.3 Minimum ra

21、ted flowDevices shall comply with the requirements in this Standard when tested at the manufacturers minimum rated flow or 9.5 L/min (2.5 gpm), whichever is lower.3.4 PressureDevices shall be designed for a rated pressure between 140.0 and 862.0 kPa (20.0 and 125.0 psi).3.5 Temperature3.5.1 Devices

22、shall be designed to be the final temperature control.3.5.2 Devices shall be adjustable from the cold position up to at least 37.8 C (100.0F) with hot water inlet temperatures ranging from 48.9 to 82.2 C (120.0 to 180.0F) and cold water inlet temperatures ranging from 4.0 to 26.7 C (40.0 to 80.0F).3

23、.5.3 Devices shall(a) be equipped with an adjustable means to limit the setting towards the hot position;(b) be capable of limiting the maximum outlet temperature to 48.9 C (120.0F) or the manufacturers stated maximum outlet temperature, whichever is less; and(c) maintain an outlet temperature withi

24、n 2.0 C (3.6F) from the set temperature in accordance with Section 4.6.3.6 ServicingThe internal parts of concealed devices shall be accessible from the finished wall line for inspection, repairs, or replacement.3(Replaces p. 3, October 2011) The American Society of Sanitary Engineering The American

25、 Society of Mechanical EngineersASSE 1016-2011/ASME A112.1016-2011/CSA B125.16-11 2013 CSA GroupOctober 2013Section IV4 Performance requirements and test methods4.1 GeneralTests shall be conducted on the same specimen, in the order listed in this Standard.4.2 Conditioning4.2.1 PreconditioningBefore

26、testing, specimens shall be conditioned at ambient laboratory conditions for not less than 12 h.4.2.2 High-temperature conditioning4.2.2.1 PurposeThe purpose of the high-temperature conditioning is to determine if the device can withstand the maximum temperatures specified in Section 3.5.4.2.2.2 Pro

27、cedureSpecimens shall be conditioned as follows:(a) Set up the specimen in accordance with Figure 1, with shut off valves V1 and V2 and valve V3 in the full open position.(b) Establish and maintain an equal pressure of 310.3 13.8 kPa (45.0 2.0 psi) on both the hot and cold water supplies.(c) Set the

28、 hot water temperature to 82.2 +0.0, -6.0 C (180.0 +0.0, -10.0F).(d) Set the cold water temperature to 10.0 3.0 C (50.0 5.0F).(e) Adjust the outlet temperature to the maximum allowable outlet temperature, not exceeding 48.9 C (120.0F).(f) Adjust valve V3 to reduce the flow rate to 9.5 1.0 L/min (2.5

29、 0.3 gpm) or the manufacturers minimum rated flow 10%.(g) Allow the water to flow through the specimen for 5 min.(Replaces p. 4, October 2011)4 The American Society of Sanitary Engineering The American Society of Mechanical Engineers 2013 CSA GroupPerformance requirements for automatic compensating

30、valves for individual showers and tub/shower combinationsOctober 2013(e) Adjust valve V3 so that the device delivers 9.5 1.0 L/min (2.5 0.3 gpm) and maintain the conditions established in Items (b) to (d) or, if the manufacturers minimum rated flow is less than 9.5 1.0 L/min (2.5 0.3 gpm), adjust va

31、lve V3 to the manufacturers minimum rated flow +1.0, 0.0 L/min (+0.3, 0.0 gpm) and maintain the conditions established in Items (b) to (d).Note: Adjustments in Items (b) to (e) are an iterative process.(f) Flow water through the device for 1 min.(g) Record the initial outlet set temperature.4.6.4 Pr

32、ocedure Type P devicesThe pressure changes specified in this Section shall be accomplished in less than 1 s. In addition to the procedures specified in Sections 4.6.2 and 4.6.3, the following test procedure shall be conducted:(a) Decrease the hot water supply pressure by 50% to 155.1 13.8 kPa (22.5

33、2.0 psi). Observe and record the temperature changes at the outlet temperature sensor T3 for 25 5 s.(b) Restore the conditions as described in Section 4.6.3. Increase the hot water supply pressure by 50% to 465.4 13.8 kPa (67.5 2.0 psi). Observe and record the temperature changes at the outlet tempe

34、rature sensor T3 for 25 5 s.(c) Restore the conditions as described in Section 4.6.3. Decrease cold water supply pressure by 50% to 155.1 1 3.8 kPa (22.5 2.0 psi). Observe and record the temperature changes at the outlet temperature sensor T3 for 25 5 s.(d) Restore the conditions as described in Sec

35、tion 4.6.3. Increase the cold water supply pressure by 50% to 465.4 13.8 kPa (67.5 2.0 psi). Observe and record the temperature changes at the outlet temperature sensor T3 for 25 5 s.4.6.5 Procedure Type T devicesThe pressure changes specified in this Section shall be accomplished in less than 1 s.

36、In addition to the procedures specified in Sections 4.6.2 and 4.6.3, the following test procedure shall be conducted:(a) Decrease the hot water supply pressure by 20% to 248.2 13.8 kPa (36.0 2.0 psi). Observe and record temperature changes at the outlet temperature sensor T3 for 25 5 s.(b) Restore c

37、onditions as described in Items (a) to (g) of Section 4.6.3. Increase the hot water supply pressure by 20% to 372.3 13.8 kPa (54.0 2.0 psi). Observe and record the temperature changes at the outlet temperature sensor T3 for 25 5 s.(c) Restore conditions as described in Items (a) to (g) of Section 4.

38、6.3. Decrease the cold water supply pressure by 20% to 248.2 13.8 kPa (36.0 2.0 psi). Observe and record the temperature changes at the outlet temperature sensor T3 for 25 5 s.(d) Restore conditions as described in Items (a) to (g) of Section 4.6.3. Increase the cold water pressure by 20% to 372.3 1

39、3.8 kPa (54.0 2.0 psi). Observe and record the temperature changes at the outlet temperature sensor T3 for 25 5 s.(e) Restore conditions as described in Items (a) to (g) of Section 4.6.3. Increase the hot water supply temperature by 13.8 0.6 C (25.0 1.0F) at a rate of 3.0 0.6 C (5.0 1.0F) per minute

40、. Observe and record the temperature changes at the outlet temperature sensor T3 for 25 5 s.4.6.6 Procedure Type T/P devicesType T/P devices shall be tested in accordance with Sections 4.6.4 and 4.6.5.4.6.7 Failure criteria Type P devicesWhen tested in accordance with Section 4.6.4, an outlet temper

41、ature variation exceeding 2.0 C (3.6F) from the initial outlet set temperature at the outlet temperature sensor T3 shall result in a rejection of the device.9(Replaces p. 9, October 2011) The American Society of Sanitary Engineering The American Society of Mechanical EngineersASSE 1016-2011/ASME A11

42、2.1016-2011/CSA B125.16-11 2013 CSA GroupOctober 20134.6.8 Failure criteria Type T devicesWhen tested in accordance with Section 4.6.5, the temperature change from the initial outlet set temperature shall not(a) within the initial 5 s following a temperature change at sensor T3,(i) exceed +3.0 C (+5

43、.4F) for more than 1.5 s (see Figures B.1 and B.3); and(ii) exceed 5.0 C (9.0F) for more than 1 s (see Figures B.2 and B.3); and(b) after the initial 5 s following a temperature change at sensor T3, exceed 2.0 C (3.6F) (see Figure B.3).4.6.9 Failure criteria Type T/P devicesWhen tested in accordance

44、 with Section 4.6.6, an outlet temperature variation exceeding 2.0 C (3.6F) from the initial outlet set temperature at the outlet temperature sensor T3 shall result in a rejection of the device.4.7 Water supply failure test All types4.7.1 PurposeThe purpose of the water supply failure test is to det

45、ermine if the device automatically reduces the discharge flow to reduce the risk of scalding and thermal shock of the user when the water supply is suddenly interrupted.4.7.2 Procedure4.7.2.1 The specimen shall be set up as shown in Figure 1 and in accordance with the conditions specified in Items (

46、a) to (f) of Section 4.6.3.4.7.2.2 After the device flows for 1 min at the parameters specified in Section 4.7.2.1, the following tests shall be conducted:(a) Close the cold water supply valve within 1 s (cold water supply failure test). Continuously record the outlet temperature at sensor T3 and fl

47、ow rate for 5 s after the cold water supply valve has been fully closed.(b) Re-establish the initial test parameters specified in Section 4.7.2.1.(c) Repeat the test by closing the hot water supply valve within 1 s (hot water supply failure test). Continuously record the outlet temperature at sensor

48、 T3 and flow rate for 5 s after the hot water supply valve has been fully closed.4.7.3 Failure criteriaWhen tested in accordance with Section 4.7.2, failure of the device to reduce the flow to 1.9 L/min (0.5 gpm) or 30% of the manufacturers minimum rated flow, whichever is less, within 5 s, shall re

49、sult in a rejection of the device.During the procedure specified in Section 4.7.2.2(a) (i.e., the cold water supply failure test), failure of the device to reduce the flow to 1.9 L/min (0.5 gpm) or 30% of the manufacturers minimum rated flow, whichever is less, prior to the water temperature at sensor T3 exceeding 48.9 C (120.0F) shall result in a rejection of the device.4.8 Mechanical temperature limit stop test4.