CEN TS 14758-3-2006 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 3 Guidance for installation《无.pdf

《CEN TS 14758-3-2006 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 3 Guidance for installation《无.pdf》由会员分享，可在线阅读，更多相关《CEN TS 14758-3-2006 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 3 Guidance for installation《无.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、DRAFT FOR DEVELOPMENTDD CEN/TS 14758-3:2006Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene with mineral modifier(s) (PP-MD) Part 3: Guidance for installationICS 93.030g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50

2、g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58DD CEN/TS 14758-3:2006This Draft for Development was published under the authority of the Standards Policy and Strategy Committee on 30 June 2006 BSI 2006ISBN 0 580 48707 5National forewordThi

3、s Draft for Development is the official English language version of CEN/TS 14758-3:2006.This publication is not to be regarded as a British Standard.It is being issued in the Draft for Development series of publications and is of a provisional nature. It should be applied on this provisional basis,

4、so that information and experience of its practical application can be obtained.A review of this Draft for Development will be carried out not later than 2 years after its publication.Notification of the start of the review period, with a request for the submission of comments from users of this Dra

5、ft for Development, will be made in an announcement in the appropriate issue of Update Standards. According to the replies received, the responsible BSI Committee will judge whether the Draft for Development can be converted into a British Standard or what other action should be taken.Observations w

6、hich it is felt should receive attention before the official call for comments will be welcomed. These should be sent to the Secretary of the responsible BSI Technical Committee, Subcommittee PRI/88/1, Plastics piping for non-pressure applications, at British Standards House, 389 Chiswick High Road,

7、 London W4 4AL, giving the document reference and clause number and proposing, where possible, an appropriate revision of the text.A list of organizations represented on this subcommittee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international

8、or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to inc

9、lude all the necessary provisions of a contract. Users are responsible for its correct application. Summary of pagesThis document comprises a front cover, an inside front cover, the CEN/TS title page, pages 2 to 9 and a back cover.The BSI copyright notice displayed in this document indicates when th

10、e document was last issued.Amendments issued since publicationAmd. No. Date CommentsTECHNICAL SPECIFICATIONSPCIFICATION TECHNIQUETECHNISCHE SPEZIFIKATIONCEN/TS 14758-3May 2006ICS 93.030English VersionPlastics piping systems for non-pressure underground drainageand sewerage - Polypropylene with miner

11、al modifier(s) (PP-MD)- Part 3: Guidance for installationSystmes de canalisations en plastique pour lesbranchements et les collecteurs dassainissement enterrssans pression - Polypropylne avec des modificateursminraux (PP-MD) - Partie 3 : Guide de poseKunststoff-Rohrleitungssysteme fr erdverlegteAbwa

12、sserkanle und -leitungen - Polypropylen mitmineralischen Additiven (PP-MD) - Teil 3: Empfehlungenfr die VerlegungThis Technical Specification (CEN/TS) was approved by CEN on 11 September 2005 for provisional application.The period of validity of this CEN/TS is limited initially to three years. After

13、 two years the members of CEN will be requested to submit theircomments, particularly on the question whether the CEN/TS can be converted into a European Standard.CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS availablepromptly a

14、t national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)until the final decision about the possible conversion of the CEN/TS into an EN is reached.CEN members are the national standards bodies of Austria, Belgium, Cyprus,

15、Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EURO

16、PEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. CEN/TS 14758-3:2006: E2 Contents page Foreword.3 1 Scope4 2 Normative referenc

17、es.4 3 Choice of stiffness (SN) series4 4 Storage in sunlight5 5 Handling and installation at low temperature6 6 Push-fit joints (elastomeric sealings)6 7 Maximum deviation from straightness6 8 Connection to rigid structures7 9 Repairs.7 10 Connection to existing pipes.8 11 Testing on site8 Bibliogr

18、aphy9 CEN/TS 14758-3:20063 Foreword This Technical Specification (CEN/TS 14758-3:2006) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This Technical Specification is a Part of a System Standard for plastics

19、piping systems of a particular material for a specified application. There are a number of such System Standards. System Standards are based on the results of the work undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids“, which is a Technical Committee of the In

20、ternational Organization for Standardization (ISO). They are supported by separate standards on test methods to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommended practice for installation

21、. EN 14758 consists of the following Parts, under the general title Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene with mineral modifier(s) (PP-MD) Part 1: Specifications for pipes, fittings and the system Part 2: Guidance for the assessment of conformity Pa

22、rt 3: Guidance for installation (this Technical Specification) According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this CEN Technical Specification: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finlan

23、d, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. CEN/TS 14758-3:20064 1 Scope This Technical Specification, together with ENV 1046 and

24、 EN 1610, provides a material-specific set of guidelines for the installation of piping systems made of polypropylene with mineral modifier(s) (PP-MD) in the field of non-pressure underground drainage and sewerage. outside the building structure (application area code “U“); both buried in ground wit

25、hin the building structure (application area code “D“) and outside the building. This is reflected in the marking of products by “U“ and “UD“. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cite

26、d applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ENV 1046:2001, Plastics piping and ducting systems Systems outside building structures for the conveyance of water or sewage Practices for installation above and below ground EN 1610:

27、1997, Construction and testing of drains and sewers EN ISO 178, Plastics Determination of flexural properties (ISO 178:2001) EN ISO 9967, Plastics pipes Determination of creep ratio (ISO 9967:1994) 3 Choice of stiffness (SN) series 3.1 General PP-MD pipe is a flexible pipe. When loaded a flexible pi

28、pe deflects and presses into the surrounding material. This generates a reaction in the surrounding materials which controls deflection of the pipe. The amount of deflection, which occurs is limited by the care exercised in the selection and laying of the bedding and side fill materials. 3.2 Pipes 3

29、.2.1 Standard procedure The choice of the stiffness (SN) series may be made: when the same class of pipe has previously proved to be satisfactory in the same condition; or based on local practice (place of installation, usual installation procedure and experience); or based on local regulation; or b

30、ased on Tables 1 and 2 of ENV 1046:2001; or based on structural design. CEN/TS 14758-3:20065 3.2.2 Structural design If a static calculation is required, information on methods is given in EN 1295-1 and the following parameters apply: Flexural modulus: E(1min) 1600-3600 MPa determined in accordance

31、with EN ISO 178 depending on the compound; Creep ratio: 200 mm: R 500dn. Care may be necessary to avoid any extra stress on the socket joint itself. The greatest permitted angular deflection in the socket should be as follows: 2 for dn 315 mm; 1,5 for 315 mm 630 mm. Larger angular deflections are pe

32、rmitted in case of joints specifically designed for large angular deflections. In these cases the manufacturer shall declare the designed angular deflection. CEN/TS 14758-3:20067 NOTE Approximately h L2/2R and L/R ( in radians). Figure 1 Parameters of deviation from straightness 8 Connection to rigi

33、d structures Special fittings for this purpose are available. In such cases the manufacturers instructions should be followed. 9 Repairs Slip-couplers or purpose-designed special fittings are available from manufacturers for effecting repairs. Because designs vary, it is necessary to follow individu

34、al manufacturers instructions. However, in the absence of such instructions, it is recommended that the following instructions are used: a) full extent of the damaged or failed section shall be identified and removed; b) cut pipe ends shall be square and shall be prepared for push-fit jointing as de

35、scribed in 6c); c) repair, or slip-, couplings shall be placed in position. The replacement pipe length shall then be laid on the suitably prepared bed and the slip-couplings moved to their final positions (see Figure 2); d) embedment shall then be replaced to give compaction values approximately eq

36、ual to those immediately adjacent to the repair. Figure 2 Repairs using slip-couplers CEN/TS 14758-3:20068 10 Connection to existing pipes For PP-MD pipelines an additional connection can be made in a manner similar to that for making a repair when an appropriate fitting is used. Alternatively, a sa

37、ddle connection may be made, in which case the manufacturers instructions should be followed. 11 Testing on site PP-MD non-pressure pipelines shall be tested according to the procedures described in Clause 13 of EN 1610:1997. PP-MD pipes are not porous, therefore it is possible to use more stringent

38、 parameters and requirements. In this case, the following are proposed: a) testing with air: 1) testing method : LC; 2) test pressure : 100 mbar (10 kPa); 3) pressure drop : 5 mbar (0,5 kPa); 4) testing time : 3 min for dn 400 mm; 0,01dnmin for dn 400 mm. b) testing with water: 1) 0,04 l/m2during 30

39、 min for pipelines; 2) 0,05 l/m2during 30 min for manholes and inspection chambers. CEN/TS 14758-3:20069 Bibliography 1 EN 14758-1:2005, Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene with mineral modifier(s) (PP-MD) Part 1: Specifications for pipes, fitting

40、s and the system 2 EN 1295-1, Structural design of buried pipelines under various conditions of loading Part 1: General requirements. CEN/TS 14758-3:2006DD CEN/TS 14758-3:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for pr

41、eparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editio

42、ns.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the insid

43、e front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications s

44、hould be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have

45、been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also ava

46、ilable which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standa

47、rds. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extr