EN 943-1-2015 en Protective clothing against liquid and gaseous chemicals including liquid aerosols and solid particles - Part 1 Performance requirements for ventilated and non-ven.pdf

《EN 943-1-2015 en Protective clothing against liquid and gaseous chemicals including liquid aerosols and solid particles - Part 1 Performance requirements for ventilated and non-ven.pdf》由会员分享，可在线阅读，更多相关《EN 943-1-2015 en Protective clothing against liquid and gaseous chemicals including liquid aerosols and solid particles - Part 1 Performance requirements for ventilated and non-ven.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 943-1:2015Protective clothing againstdangerous solid, liquid andgaseous chemicals, includingliquid and solid aerosolsPart 1: Performance requirements for Type 1(gas-tight) chemical protective suitsBS EN 943-1:2015 BRITISH STANDARDNational forewordThis British Standard

2、is the UK implementation of EN 943-1:2015. It supersedes BS EN 943-1:2002 which is withdrawn.BSI, as a member of CEN, is obliged to publish EN 943-1:2015 as a British Standard. However, attention is drawn to the fact that during the development of this European Standard, the UK committee voted again

3、st its approval as a European Standard.The following concerns regarding this standard have been expressed by the UK committee: This standard supersedes BS EN 943-1:2002, which specifiesperformance requirements for both Type 1 and Type 2 chemicalprotective clothing. However, EN 943-1:2015 does not in

4、clude anyrequirements for Type 2 clothing. No alternative provision has beenmade for the standardization of Type 2 chemical protective clothing. Conformance with EN 943-1 is a prerequisite of EN 943-2. The revisionof EN 943-2 has not kept pace with that of EN 943-1 with the resultthat the links betw

5、een the old part 2 and the new part 1 are nolonger compliant with one another. This will make it difficult formanufacturers to approve or re-approve EN 943-2:2002 products.However, it is intended for EN 943-2 to be revised in the future andfor the two parts to once again be mutually compatible. EN 9

6、43-1:2015 includes several new test procedures which have notbeen assessed for repeatability or reproducibility.Further commentary on EN 943-1:2015 from UK Technical Committee PH/3/3 can be found in National Annex NA of this document.The UK participation in its preparation was entrusted by Technical

7、 Committee PH/3, Protective clothing, to Subcommittee PH/3/3, Chemical, Biological, Radioactive and Nuclear Personal Protective Equipment.A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all the necessar

8、y provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN 978 0 580 76736 4ICS 13.340.10Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was

9、published under the authority of the Standards Policy and Strategy Committee on 31 May 2016.Amendments/corrigenda issued since publicationDate Text affectedBS EN 943-1:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 943-1 August 2015 ICS 13.340.10 Supersedes EN 943-1:2002English Version Pro

10、tective clothing against dangerous solid, liquid and gaseous chemicals, including liquid and solid aerosols - Part 1: Performance requirements for Type 1 (gas-tight) chemical protective suits Vtements de protection contre les produits chimiques dangereux solides, liquides et gazeux, y compris les ar

11、osols liquides et les particules solides - Partie 1: Exigences de performance des combinaisons de protection chimique tanches aux gaz (type 1) Schutzkleidung gegen gefhrliche feste, flssige und gasfrmige Chemikalien, einschlielich Flssigkeitsaerosole und feste Partikel - Teil 1: Leistungsanforderung

12、en fr Typ 1 (gasdichte) Chemikalienschutzkleidung This European Standard was approved by CEN on 27 June 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alter

13、ation. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made

14、 by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estoni

15、a, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDA

16、RDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 943-1:2015 EBS EN 943-1:2015EN 943-1:2015

17、 (E) 2 Contents Page European foreword .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Performance requirements .8 4.1 General 8 4.2 Materials .8 4.3 Seams, joins, and assemblages 11 4.4 Strength of detachable joins . 12 4.5 Permeation requirement for closure . 12 5 Requirements f

18、or the whole suit . 12 5.1 General . 12 5.2 Compatibility with other equipment 14 5.3 Conditioning to simulate storage conditions 14 5.4 Leak tightness (static inflation test) . 14 5.5 Total inward leakage test . 14 5.6 Visor . 15 5.6.1 General . 15 5.6.2 Distortion of vision . 15 5.6.3 Distortion o

19、f vision after chemical exposure . 15 5.6.4 Field of vision 15 5.6.5 Mechanical strength . 15 5.7 Face piece for suits without integral visor . 15 5.8 Pass-through . 16 5.8.1 General . 16 5.8.2 Strength of pass-through . 16 5.8.3 Performance of pass-through providing breathing air . 16 5.9 Airline s

20、upply system . 16 5.9.1 General . 16 5.9.2 Couplings 16 5.9.3 Connections 16 5.9.4 Connections strength . 17 5.10 Exhaust assembly. 17 5.11 Pressure in chemical protective suit 17 5.12 External ventilating hose . 17 5.13 Air flow rate of breathing air and/or ventilating air supply. 17 5.13.1 General

21、 . 17 5.13.2 Continuous flow valve for Type 1c breathing air supply 17 5.13.3 Warning and measuring facilities . 18 5.13.4 Compressed air supply tube . 18 5.14 Carbon dioxide content of inhalation air 18 5.15 Noise associated with air supply to suit 18 5.16 Practical Performance 19 6 Test methods .

22、19 6.1 Visual inspection 19 6.2 Practical performance test . 19 6.2.1 General . 19 6.2.2 Work simulation test 20 6.2.3 Information to be recorded 21 6.3 Suit pressure test 21 BS EN 943-1:2015EN 943-1:2015 (E) 3 6.4 Pull test for joins and assemblages 21 6.5 Exhalation valves 22 6.5.1 Leak tightness

23、test 22 6.5.2 Connection between exhalation valve (exhaust assembly) and chemical protective clothing material 22 6.6 Mechanical strength test for visor . 22 6.7 Distortion of vision after chemical exposure . 23 7 Marking . 23 8 Information supplied by the manufacturer . 24 Annex A (normative) Total

24、 inward leakage test 26 A.1 Principle 26 A.2 Test subjects 26 A.3 Sodium chloride method 26 A.3.1 Aerosol generator 26 A.3.2 Test agent . 26 A.3.3 Detection 26 A.3.4 Flame photometer . 27 A.3.5 Sample pump . 27 A.3.6 Sampling of chamber concentration . 27 A.4 Sulphur hexafluoride method (SF6) 28 A.4

25、.1 Test agent . 28 A.4.2 Detection 29 A.5 Sampling probe . 29 A.6 Test chamber . 30 A.7 Treadmill . 30 A.8 Test procedure . 30 A.8.1 Test subject 30 A.8.2 Test protocol 31 A.8.3 Assessment of results 32 Annex B (normative) Material tests . 33 B.1 General . 33 B.2 Material tests - Resistance to ignit

26、ion . 33 Annex C (normative) Optical Chart 34 Annex D (informative) Adapted test cell for testing closures (zipper) 35 Annex E (informative) Significant technical changes between this document and the previous edition of this European Standard . 36 Annex ZA (informative) Relationship between this Eu

27、ropean Standard and the Essential Requirements of EU Directive 89/686/EEC . 37 Bibliography 39 BS EN 943-1:2015EN 943-1:2015 (E)BS EN 943-1:2015EN 943-1:2015 (E) 2 Contents Page European foreword .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Performance requirements .8 4.1 Gener

28、al 8 4.2 Materials .8 4.3 Seams, joins, and assemblages 11 4.4 Strength of detachable joins . 12 4.5 Permeation requirement for closure . 12 5 Requirements for the whole suit . 12 5.1 General . 12 5.2 Compatibility with other equipment 14 5.3 Conditioning to simulate storage conditions 14 5.4 Leak t

29、ightness (static inflation test) . 14 5.5 Total inward leakage test . 14 5.6 Visor . 15 5.6.1 General . 15 5.6.2 Distortion of vision . 15 5.6.3 Distortion of vision after chemical exposure . 15 5.6.4 Field of vision 15 5.6.5 Mechanical strength . 15 5.7 Face piece for suits without integral visor .

30、 15 5.8 Pass-through . 16 5.8.1 General . 16 5.8.2 Strength of pass-through . 16 5.8.3 Performance of pass-through providing breathing air . 16 5.9 Airline supply system . 16 5.9.1 General . 16 5.9.2 Couplings 16 5.9.3 Connections 16 5.9.4 Connections strength . 17 5.10 Exhaust assembly. 17 5.11 Pre

31、ssure in chemical protective suit 17 5.12 External ventilating hose . 17 5.13 Air flow rate of breathing air and/or ventilating air supply. 17 5.13.1 General . 17 5.13.2 Continuous flow valve for Type 1c breathing air supply 17 5.13.3 Warning and measuring facilities . 18 5.13.4 Compressed air suppl

32、y tube . 18 5.14 Carbon dioxide content of inhalation air 18 5.15 Noise associated with air supply to suit 18 5.16 Practical Performance 19 6 Test methods . 19 6.1 Visual inspection 19 6.2 Practical performance test . 19 6.2.1 General . 19 6.2.2 Work simulation test 20 6.2.3 Information to be record

33、ed 21 6.3 Suit pressure test 21 BS EN 943-1:2015EN 943-1:2015 (E) 3 6.4 Pull test for joins and assemblages 21 6.5 Exhalation valves 22 6.5.1 Leak tightness test 22 6.5.2 Connection between exhalation valve (exhaust assembly) and chemical protective clothing material 22 6.6 Mechanical strength test

34、for visor . 22 6.7 Distortion of vision after chemical exposure . 23 7 Marking . 23 8 Information supplied by the manufacturer . 24 Annex A (normative) Total inward leakage test 26 A.1 Principle 26 A.2 Test subjects 26 A.3 Sodium chloride method 26 A.3.1 Aerosol generator 26 A.3.2 Test agent . 26 A.

35、3.3 Detection 26 A.3.4 Flame photometer . 27 A.3.5 Sample pump . 27 A.3.6 Sampling of chamber concentration . 27 A.4 Sulphur hexafluoride method (SF6) 28 A.4.1 Test agent . 28 A.4.2 Detection 29 A.5 Sampling probe . 29 A.6 Test chamber . 30 A.7 Treadmill . 30 A.8 Test procedure . 30 A.8.1 Test subje

36、ct 30 A.8.2 Test protocol 31 A.8.3 Assessment of results 32 Annex B (normative) Material tests . 33 B.1 General . 33 B.2 Material tests - Resistance to ignition . 33 Annex C (normative) Optical Chart 34 Annex D (informative) Adapted test cell for testing closures (zipper) 35 Annex E (informative) Si

37、gnificant technical changes between this document and the previous edition of this European Standard . 36 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 89/686/EEC . 37 Bibliography 39 BS EN 943-1:2015EN 943-1:2015 (E)BS EN 943-1:201

38、5EN 943-1:2015 (E) 4 European foreword This document (EN 943-1:2015) has been prepared by Technical Committee CEN/TC 162 “Protective clothing including hand and arm protection and lifejackets”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national st

39、andard, either by publication of an identical text or by endorsement, at the latest by February 2016, and conflicting national standards shall be withdrawn at the latest by February 2016. This document supersedes EN 943-1:2002. This document has been prepared under a mandate given to CEN by the Euro

40、pean Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. For details of the significant changes made since EN 943-1:2002 please refer t

41、o Annex E. EN 943 consists of the following parts: EN 943-1, Protective clothing against solid, liquid and gaseous chemicals, including liquid and solid aerosols Part 1: Performance requirements for Type 1 (gas-tight) chemical protective suits EN 943-2, Protective clothing against solid, liquid and

42、gaseous chemicals, including aerosols Part 2: Performance requirements for Type 1 gas-tight chemical protective suits for emergency teams (ET) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held re

43、sponsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Fi

44、nland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 943-1:2015EN 943-1:2015

45、(E) 5 1 Scope This European Standard specifies the minimum requirements, test methods, marking and information supplied by the manufacturer for ventilated and non-ventilated gas-tight chemical protective suits. It specifies full body personal protective ensembles to be worn for protection against so

46、lid, liquid and gaseous chemicals, including liquid and solid aerosols. This standard does not establish minimum criteria for protection for non-chemical hazards, e.g. radiological, fire, heat, explosive, infective agents. This type of equipment is not intended for total immersion in liquids. The se

47、ams, joins and assemblages attaching the accessories are included within the scope of this standard. This standard specifies only supplementary requirements for components. The basic performance criteria for the components gloves, boots or respiratory protective equipment are given in other European

48、 Standards. Particulate protection is limited to physical penetration of the particulates only. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited app

49、lies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 132, Respiratory protective devices - Definitions of terms and pictograms EN 136:1998, Respiratory protective devices - Full face masks - Requirements, testing, marking EN 388, Protective gloves against mechanical risks EN 1073-2, Protective clothing against radioactive contamination - Part 2: Requirements and test methods for non-ventilated protective clothing against particulate radioactive contamination EN 12021, Respiratory equipment - Compressed g