CEN TR 15339-5-2014 Thermal spraying - Safety requirements for thermal spraying equipment - Part 5 Powder and wire feed units《热喷涂 热喷涂设备的安全要求 第5部分 粉末和送丝单元》.pdf

《CEN TR 15339-5-2014 Thermal spraying - Safety requirements for thermal spraying equipment - Part 5 Powder and wire feed units《热喷涂 热喷涂设备的安全要求 第5部分 粉末和送丝单元》.pdf》由会员分享，可在线阅读，更多相关《CEN TR 15339-5-2014 Thermal spraying - Safety requirements for thermal spraying equipment - Part 5 Powder and wire feed units《热喷涂 热喷涂设备的安全要求 第5部分 粉末和送丝单元》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationPD CEN/TR 15339-5:2014Thermal spraying Safetyrequirements for thermalspraying equipmentPart 5: Powder and wire feed unitsPD CEN/TR 15339-5:2014 PUBLISHED DOCUMENTNational forewordThis Published Document is the UK implementation of CEN/TR15339-5:2014.The UK participation in i

2、ts preparation was entrusted to TechnicalCommittee STI/40, Thermal spraying and thermally sprayed coatings.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users ar

3、e responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 78895 6ICS 25.220.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This Published Document was published under the authority of theS

4、tandards Policy and Strategy Committee on 31 December 2014.Amendments issued since publicationDate Text affectedPD CEN/TR 15339-5:2014TECHNICAL REPORT RAPPORT TECHNIQUE TECHNISCHER BERICHT CEN/TR 15339-5 December 2014 ICS 25.220.20 English Version Thermal spraying - Safety requirements for thermal s

5、praying equipment - Part 5: Powder and wire feed units Projection thermique - Exigences de scurit relatives au matriel de projection thermique - Partie 5: Dispositifs dalimentation en poudre et en fil Thermisches Spritzen - Sicherheitsanforderungen fr Einrichtungen fr das thermische Spritzen - Teil

6、5: Pulver- und Drahtfrdereinheiten This Technical Report was approved by CEN on 16 September 2014. It has been drawn up by the Technical Committee CEN/TC 240. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Form

7、er Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT

8、EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TR 15339-5:2014 EPD CEN/TR 15339-5:2014CEN/TR 15339-5:20

9、14 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Function of the powder and wire feed units .4 3.1 General 4 3.2 Features of the powder feed unit .4 3.3 Features of the wire feed unit .5 3.3.1 Flame spraying .5 3.3.2 Arc spraying .5 4 Potential hazards .5 4.1 General 5 4.2 Powd

10、er feed units 5 4.3 Wire feed units .5 5 Safety requirements Protection measures .6 5.1 General 6 5.2 Safety requirements and protection measures for powder feed units in the case of flame, HVOF, and plasma spraying .6 5.3 Safety requirements for wire feed units and protection measures in the case o

11、f arc spraying 6 6 Requirements for manufacture, supply, service and maintenance6 6.1 Requirements of the manufacturer 6 6.2 Requirements of the integrator 7 6.3 Requirements of the user .7 7 National rules .7 Bibliography 8 PD CEN/TR 15339-5:2014CEN/TR 15339-5:2014 (E) 3 Foreword This document (CEN

12、/TR 15339-5:2014) has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed coatings”, the secretariat of which is held by DIN. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC s

13、hall not be held responsible for identifying any or all such patent rights. CEN/TR 15339, Thermal spraying - Safety requirements for thermal spraying equipment is composed of the following parts: Part 1: General requirements Part 2: Gas control units (published as a European Standard) Part 3: Torche

14、s for thermal spraying and their connection and supply units Part 4: Gas and liquid fuel supply Part 5: Powder and wire feed units Part 6: Spray booth, Handling system, Dust collection, Exhaust system, Filter PD CEN/TR 15339-5:2014CEN/TR 15339-5:2014 (E) 4 1 Scope This Technical Report specifies saf

15、ety requirements of equipment for thermal spraying, in this case of powder and wire feed units. This part of CEN/TR 15339 should be used in conjunction with CEN/TR 15339-1, which deals with general aspects of designing, manufacturing, and/or putting in service of machines or equipment and with the r

16、esponsibility for issuing the CE Conformity Declaration. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the lates

17、t edition of the referenced document (including any amendments) applies. CEN/TR 15339-1, Thermal spraying Safety requirements for thermal spraying equipment Part 1: General requirements EN 657, Thermal spraying Terminology, classification EN 1395-7, Thermal spraying Acceptance inspection of thermal

18、spraying equipment Part 7: Powder feed systems 3 Function of the powder and wire feed units 3.1 General Thermal spray processes are described and schematically represented in EN 657. The feed unit shall enable a uniform processing of the spraying material and shall be suitable for operation with the

19、 spraying equipment to be intended for spray application. 3.2 Features of the powder feed unit The powder feed unit can be of type: stand-alone; or integrated in the torch system; and its operation mode can be: independent; or in automatic/remote mode controlled by the spray control system. The powd

20、er feed rate shall be adjustable. The actual values shall be constant and reproducible in relation to the set values; this requires an adequate flow rate and a constant pressure of the carrier gas. The powder feed unit shall be able to operate inside or outside of a spray booth, subject to practical

21、 limits on the length of powder feed hose from the feeder to the torch. The acceptance inspection of the powder feed unit is specified in EN 1395-7. PD CEN/TR 15339-5:2014CEN/TR 15339-5:2014 (E) 5 3.3 Features of the wire feed unit 3.3.1 Flame spraying Usually the wire feed rate for flame spraying i

22、s set by the speed regulation of an air turbine or air motor. It may also be set by adjustment of an electric motor manually or through a more sophisticated control. 3.3.2 Arc spraying The wire feed rate for arc spraying is set by the adjustment of an electric motor or an air motor and the push and/

23、or pull drives connected with that. There is an almost linear relationship between wire feed rate and current so it is common to express the feed rate in amperes. In some systems, the current itself is set and the wire feed rate automatically adjusted to give the set current. A uniform, controllable

24、, and reproducible wire feed rate shall be provided by the regulated motor. An adequate and constant air pressure and flow rate or electrical power supply shall also be provided. 4 Potential hazards 4.1 General For a safe operation of the powder or wire feed unit, the following hazards shall be cons

25、idered for normal operation or abnormal foreseeable circumstances. 4.2 Powder feed units The following hazards shall be considered: gas leakage from the powder feed unit and/or the hoses; gas escape under high pressure; static charging in powder supply hoses with risk of sparks and shocks; back flow

26、 of hot or flammable gases in the case of excessive pressure in the combustion chamber for HVOF spraying; exposure of the operating personnel to harmful dust when filling, emptying, or cleaning the powder feed unit. An adequate pressure release shall be ensured before opening; risk of explosion due

27、to powder distributed outside the powder feeder during filling, emptying or cleaning. 4.3 Wire feed units The operator can be injured by electric shock if live parts such as the wire reel and the wire itself can be touched. Whilst the voltage is typically less than 50 V, occasionally higher transien

28、t voltages can be generated by the inductance in the system. PD CEN/TR 15339-5:2014CEN/TR 15339-5:2014 (E) 6 5 Safety requirements Protection measures 5.1 General According to the type of the feed unit and also whether the spraying process is manually, mechanically or automatically operated specific

29、 safety requirements are to be considered and protection measures are to be carried out for normal operation or any foreseeable abnormal operation. 5.2 Safety requirements and protection measures for powder feed units in the case of flame, HVOF, and plasma spraying Concerning the safety requirements

30、 of the powder feed unit, the following items shall be considered: the relationship between the pressure in the combustion chamber of the torch and the carrier gas system shall be considered; only inert carrier gases (usually Ar or N2) should be used; to ensure gas tightness of the powder feed unit

31、and the connection hoses, a leak test shall be carried out prior to use, after installation, commissioning, after re-assembly or repair work; to provide a simple and safe method to fill and empty the powder feeder. When cleaning, filling or emptying the powder feed unit exposure of the operator to d

32、ust shall be considered. If applicable, personal protective equipment shall be used; powder spilled around the powder feeder should be extracted or cleaned up, using appropriate tools and methods before starting operation. 5.3 Safety requirements for wire feed units and protection measures in the ca

33、se of arc spraying Concerning the safety requirements of the wire feed unit, the following items shall be considered: protection against contact with electrically live parts like the wire reel and the spraying wire itself; avoidance of inadmissible high voltage at the feeder, which may impair the op

34、erator; protection against mechanical hazards such as finger trapping, etc. 6 Requirements for manufacture, supply, service and maintenance 6.1 Requirements of the manufacturer The following items shall be considered: designing and manufacturing of the equipment according to the relevant Directives

35、of the European Union and the technical instructions of CEN/TR 15339-1 and of this Technical Report; presentation of an operation manual of the equipment; service plan providing instructions for measures and testing respectively replacement of worn parts at intervals; plan for training the operators

36、. PD CEN/TR 15339-5:2014CEN/TR 15339-5:2014 (E) 7 6.2 Requirements of the integrator Installation and putting into service meeting the requirements of the Directives of the European Union and the instructions of CEN/TR 15339-1 and of this Technical Report. 6.3 Requirements of the user The following

37、items shall be considered: operating equipment meeting the requirements of the Directives of the European Union and the instructions of CEN/TR 15339-1 and of this Technical Report; preparing the operating personnel; instruction of the operator; execution of the service plan. 7 National rules Nationa

38、l laws or regulations shall be considered and can be added in the prevailing national foreword of this Technical Report, if applicable. PD CEN/TR 15339-5:2014CEN/TR 15339-5:2014 (E) 8 Bibliography 1 ATEX 95 Directive: Directive 94/9/EC of the European Parliament and the Council of 23 March 1994 on t

39、he approximation of the laws of the Member States concerning equipment and protective systems intended for use in potentially explosive atmospheres, OJ L 100, 19.4.1994, p. 129, available from: http:/eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=OJ:L:1994:100:0001:0029:EN:PDF 2 CEN/TR 15339-3, Ther

40、mal spraying Safety requirements for thermal spraying equipment Part 3: Torches for thermal spraying and their connection and supply units 3 EN 60974-5, Arc welding equipment Part 5: Wire feeders (IEC 60974-5) 4 EN 60974-10, Arc welding equipment Part 10: Electromagnetic compatibility (EMC) requirem

41、ents (IEC 60974-10) This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI

42、 Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge

43、 embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that you

44、r organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standard

45、s, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using st

46、andards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to

47、date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically re

48、ceive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as

49、 few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inac