CAN CSA-C22 2 NO 60745-2-2A-2009 Amendment 1 Hand-held motor-operated electric tools - Safety - Part 2-2 Particular requirements for screwdrivers and impact wrenches (Second Editio.pdf

《CAN CSA-C22 2 NO 60745-2-2A-2009 Amendment 1 Hand-held motor-operated electric tools - Safety - Part 2-2 Particular requirements for screwdrivers and impact wrenches (Second Editio.pdf》由会员分享，可在线阅读，更多相关《CAN CSA-C22 2 NO 60745-2-2A-2009 Amendment 1 Hand-held motor-operated electric tools - Safety - Part 2-2 Particular requirements for screwdrivers and impact wrenches (Second Editio.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、Amendment 1:2009 (MOD) toNational Standard of CanadaCAN/CSA-C22.2 No. 60745-2-2-04(IEC 60745-2-2:2003, MOD)(reaffirmed 2013)Amendment 1: Hand-held motor-operated electric tools Safety Part 2-2: Particular requirements for screwdrivers and impact wrenchesStandards Update ServiceAmendment 1:2009 toCAN

2、/CSA-C22.2 No. 60745-2-2-04March 2009Title: Amendment 1: Hand-held motor-operated electric tools Safety Part 2-2: Particular requirements for screwdrivers and impact wrenchesPagination: 7 pages (iii preliminary and 4 text)To register for e-mail notification about any updates to this publicationgo to

3、 shop.csa.caclick on CSA Update ServiceThe List ID that you will need to register for updates to this publication is 2416816.If you require assistance, please e-mail techsupportcsagroup.org or call 416-747-2233.Visit CSA Groups policy on privacy at csagroup.org/legal to find out how we protect your

4、personal information.Canadian Standards AssociationAmendment 1:2009 (MOD) to National Standard of CanadaCAN/CSA-C22.2 No. 60745-2-2-04, Second Edition(IEC 60745-2-2:2003, MOD)Underwriters Laboratories Inc.UL 60745-2-2Second EditionAmendment 1Hand-held motor-operated electric tools Safety Part 2-2:Pa

5、rticular requirements for screwdrivers and impact wrenchesAmendment publication date: MARCH 13, 2009This amendment is an adoption of IEC Amendment 1 (2008) to publication IEC 60745-2-2, Second Edition (2003).ANSI/UL 60745-2-2-2009 2009Canadian Standards AssociationAll rights reserved. No part of thi

6、s publication may be reproduced in any form whatsoever without the prior permission of the publisher.Amendment 1:2008 to International Standard IEC 60745-2-2:2003 has been adopted with National Differences (MOD) as Amendment 1:2009 to CAN/CSA-C22.2 No. 60745-2-2-04. This Amendment was reviewed by th

7、e CSA Subcommittee on Portable Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee.March 2009Copyright 2

8、009 Underwriters Laboratories Inc.Revisions of this Standard will be made by issuing revised or additional pages bearing their date of issue. A UL Standard is current only if it incorporates the most recently adopted revisions, all of which are itemized on the transmittal notice that accompanies the

9、 latest set of revised requirements. The most recent designation of ANSI/UL 60745-2-2 as an American National Standard (ANSI) occurred on January 23, 2009.This ANSI/UL Standard for Safety, which consists of the Second edition with revisions through March 13, 2009, is under continuous maintenance, wh

10、ereby each revision is ANSI approved upon publication. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/.MARCH 13, 2009 Am

11、endment 1:2009 to CAN/CSA-C22.2 No. 60745-2-2-04 UL 60745-2-2 iiiCanadian/US National Differences20DV D1 Modification: Delete Clause 20 of this Part 2.21DV D1 Modification: Delete Clause 21 of this Part 2.IEC 60745-2-2Edition 2.0 2008-05INTERNATIONAL STANDARD NORME INTERNATIONALEHand-held motor-oper

12、ated electric tools Safety Part 2-2: Particular requirements for screwdrivers and impact wrenches Outils lectroportatifs moteur Scurit Partie 2-2: Rgles particulires pour les visseuses et les cls chocs INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE DICS 25.140.2

13、0; 25.140.30 PRICE CODECODE PRIXAMENDMENT 1 AMENDEMENT 1 2 60745-2-2 Amend. 1 IEC:2008 FOREWORD This amendment has been prepared by subcommittee 61F: Safety of hand-held motor-operated electric tools, of IEC technical committee 61: Safety of household and similar electrical appliances. The text of t

14、his amendment is based on the following documents: FDIS Report on voting 61F/732/FDIS 61F/752/RVD Full information on the voting for the approval of this amendment can be found in the report on voting indicated in the above table. With this amendment, this Part 2 is established on the basis of the f

15、ourth edition (2006) of IEC 60745-1, Hand-held motor-operated electric tools Safety Part 1: General requirements. Main changes include editorial modifications to match with the fourth edition of IEC 60745-1 and the addition of a new safety warning to Clause 8: Marking and instructions. The committee

16、 has decided that the contents of this amendment and the base publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn,

17、 replaced by a revised edition, or amended. _ 1 Scope Replace the existing text of Clause 1 by the following: This clause of Part 1 is applicable, except as follows: Addition: This standard applies to screwdrivers and impact wrenches. 3 Definitions Change the title of Clause 3 to read: 3 Terms and d

18、efinitions 8 Marking and instructions Replace the existing text of Clause 8 by the following: Amendment 1:2009 to CAN/CSA-C22.2 No. 60745-2-2-0460745-2-2 Amend. 1 IEC:2008 3 This clause of Part 1 is applicable, except as follows: 8.12.1.1 Addition Hold power tool by insulated gripping surfaces, when

19、 performing an operation where the fastener may contact hidden wiring or its own cord. Fasteners contacting a “live“ wire may make exposed metal parts of the power tool “live“ and could give the operator an electric shock. 20 Mechanical strength Replace the existing text of Clause 20 by the followin

20、g: This clause of Part 1 is applicable, except as follows: 20.5 This subclause is not applicable for impact wrenches. 21 Construction Replace the existing text of Clause 21 by the following: This clause of Part 1 is applicable, except as follows: 21.32 This subclause is not applicable for impact wre

21、nches. 23 Components Replace the existing text of Clause 23 by the following: This clause of Part 1 is applicable, except as follows: 23.3 Replacement: Overload protection devices shall be of the non-self-resetting type unless the tool is equipped with a momentary switch with no provision for being

22、locked in the “on” position. Compliance is checked by inspection. Amendment 1:2009 to CAN/CSA-C22.2 No. 60745-2-2-04 4 60745-2-2 Amend. 1 IEC:2008 Annex K Battery tools and battery packs Replace the existing text of K.1.1 by the following: K.1 Addition: All clauses of this Part 2 apply unless otherw

23、ise specified in this annex. Add the following subclause: K.8.12.1.1 Replacement of this subclause of Part 2: Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live“ wire may make exposed metal parts of

24、the power tool “live“ and could give the operator an electric shock. Annex L Battery tools and battery packs provided with mains connection or non-isolated sources Replace the existing text of L.1.1 by the following: L.1 Addition: All clauses of this Part 2 apply unless otherwise specified in this a

25、nnex. _ Amendment 1:2009 to CAN/CSA-C22.2 No. 60745-2-2-04PRINTED IN CANADAIMPRIMEAU CANADA100%The Canadian Standards Association (CSA) prints its publications on Rolland Enviro100, which contains 100% recycled post-consumer fibre, is EcoLogo and Processed Chlorine Free certified, and was manufactur

26、ed using biogas energy.Copyright NoticeThis Amendment to the International Standard contains information copyright protected by theInternational Electrotechnical Commission (IEC). Except as permitted under the laws of Canada, no extract ofthis Amendment to the International Standard may be reproduce

27、d, stored in any retrieval system, ortransmitted in any form or by any means, electronic, photocopying, recording, or otherwise, without priorpermission from the Standards Council of Canada (SCC). Requests for permission to reproduce thisAmendment to the International Standard or parts thereof shoul

28、d be addressed to Manager, Technical Document Centre Standards Council of Canada 270 Albert Street, Suite 200 Ottawa, Ontario K1P 6N7 The Canadian adoption of this Amendment to the International Standard contains information copyrightprotected by the Canadian Standards Association. All rights reserv

29、ed. No part of this adopted Amendmentmay be reproduced in any form whatsoever without the prior permission of the publisher. IEC material isreprinted with permission. Requests for permission to reproduce this adopted Amendment or parts thereofshould be addressed to Director, Information Products Canadian Standards Association 5060 Spectrum Way, Suite 100 Mississauga, Ontario L4W 5N6 Copyright violators will be prosecuted to the full extent of the law.