BS PD IEC TS 62668-1-2016 Process management for avionics Counterfeit prevention Avoiding the use of counterfeit fraudulent and recycled electronic components《航空电子设备过程管理 防伪 避免使用假冒 .pdf

《BS PD IEC TS 62668-1-2016 Process management for avionics Counterfeit prevention Avoiding the use of counterfeit fraudulent and recycled electronic components《航空电子设备过程管理 防伪 避免使用假冒 .pdf》由会员分享，可在线阅读，更多相关《BS PD IEC TS 62668-1-2016 Process management for avionics Counterfeit prevention Avoiding the use of counterfeit fraudulent and recycled electronic components《航空电子设备过程管理 防伪 避免使用假冒 .pdf（74页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationProcess management for avionics Counterfeit preventionPart 1: Avoiding the use of counterfeit, fraudulent and recycled electronic componentsPD IEC/TS 62668-1:2016National forewordThis Published Document is the UK implementation of IEC/TS 62668-1:2016.It supersedes PD IEC/TS

2、62668-1:2014 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee GEL/107, Process management for avionics.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the n

3、ecessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 91438 6ICS 03.100.50; 31.020; 49.060Compliance with a British Standard cannot confer immunity fromlegal obligations.This P

4、ublished Document was published under the authority of theStandards Policy and Strategy Committee on 30 April 2016.Amendments/corrigenda issued since publicationDate Text affectedPUBLISHED DOCUMENTPD IEC/TS 62668-1:2016IEC TS 62668-1 Edition 3.0 2016-04 TECHNICAL SPECIFICATION Process management for

5、 avionics Counterfeit prevention Part 1: Avoiding the use of counterfeit, fraudulent and recycled electronic components INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 03.100.50; 31.020; 49.060 ISBN 978-2-8322-3277-4 Registered trademark of the International Electrotechnical Commission Warning! Make s

6、ure that you obtained this publication from an authorized distributor. colourinsidePD IEC/TS 62668-1:2016 2 IEC TS 62668-1:2016 IEC 2016 CONTENTS FOREWORD . 6 1 Scope 8 2 Normative references. 8 3 Terms, definitions and abbreviations 8 3.1 Terms and definitions 8 3.2 Abbreviations 12 4 Technical req

7、uirements 14 4.1 General . 14 4.2 Minimum avionics OEM requirements 15 4.3 Intellectual property . 18 4.3.1 General . 18 4.3.2 Definition of intellectual property 18 4.4 Counterfeit consideration. 19 4.4.1 General . 19 4.4.2 Legal definition of counterfeit . 19 4.4.3 Fraudulent components 19 4.4.4 H

8、ow to establish traceability . 20 4.4.5 Reasons for the loss of component traceability . 20 4.5 Why is counterfeit a problem? . 20 4.5.1 General . 20 4.5.2 General worldwide activities combating counterfeit issues . 21 4.5.3 Cultural differences 21 4.5.4 Counterfeiting activities and avionics equipm

9、ent . 22 4.5.5 Electronic components direct action groups 24 4.6 Recycled components . 25 4.6.1 General . 25 4.6.2 Why does the avionics industry not use recycled components? . 25 4.6.3 When do recycled components become suspect and potentially fraudulent? 25 4.7 Original component manufacturer (OCM

10、) anti-counterfeit guidelines . 26 4.7.1 General . 26 4.7.2 Chinese Reliable Electronic Component Supplier (RECS) audit scheme 26 4.7.3 Original component manufacturer (OCM) ISO 9001 and AS/EN/JISQ 9100 Third Party Certification . 26 4.7.4 Original component manufacturer (OCM) trademarks 26 4.7.5 Or

11、iginal component manufacturer (OCM) IP control 26 4.7.6 Original component manufacturer (OCM) physical part marking and packaging marking . 27 4.7.7 The Semiconductor Industries Association Anti Counterfeit Task Force (ACTF) 27 4.7.8 USA Trusted Foundry Program . 28 4.7.9 USA Trusted IC Supplier Acc

12、reditation Program . 28 4.7.10 Physical unclonable function (PUF) 28 4.7.11 Original component manufacturer (OCM) best practice . 28 4.8 Distributor minimum accreditations 28 4.9 Distributor AS/EN/JISQ 9120 Third Party Certification 29 4.10 Franchised distributor network . 29 PD IEC/TS 62668-1:2016I

13、EC TS 62668-1:2016 IEC 2016 3 4.10.1 General . 29 4.10.2 SAE AS6496 30 4.10.3 Control stock through tracking schemes . 30 4.10.4 Control scrap . 30 4.10.5 RECS 30 4.11 Non-franchised distributor anti-counterfeit guidelines . 30 4.11.1 General . 30 4.11.2 CCAP-101 certified program for independent di

14、stributor 31 4.11.3 SAE AS6081 31 4.11.4 OEM managed non-franchised distributors 31 4.11.5 Brokers 31 4.12 Avionics OEM anti-counterfeit guidelines when procuring components . 31 4.12.1 General . 31 4.12.2 Buy from approved sources 32 4.12.3 Traceable components . 32 4.12.4 Certificate of conformanc

15、e and packing slip 32 4.12.5 Plan and buy sufficient quantities . 33 4.12.6 Use of non- franchised distributors . 33 4.12.7 Brokers 34 4.12.8 Contact the original manufacturer . 34 4.12.9 Obsolete components and franchised aftermarket sources 34 4.12.10 IEC TS 62239-1 approved alternatives . 34 4.12

16、.11 Product redesign 34 4.12.12 Non traceable components . 35 4.12.13 OEM anti-counterfeit plans including SAE AS5553 and SAE AS6174 . 35 4.13 OEM anti-counterfeit guidelines for their products 37 4.13.1 IP control . 37 4.13.2 Tamper-proofing the OEM design . 37 4.13.3 Tamper-proof labels . 38 4.13.

17、4 Use of ASICS and FPGAs with IP protection features . 38 4.13.5 Control the final OEM product marking . 38 4.13.6 Control OEM scrap . 39 4.13.7 OEM trademarks and logos 39 4.13.8 Control delivery of OEM products and spares and their useful life . 39 4.13.9 Repairs to OEM products . 39 4.14 Counterf

18、eit, fraud and component recycling reporting . 40 4.14.1 General . 40 4.14.2 USA FAA suspected unapproved parts (SUP) program . 40 4.14.3 EASA . 40 4.14.4 UK counterfeit reporting . 40 4.14.5 EU counterfeit reporting . 40 4.14.6 UKEA anti-counterfeiting forum 40 Annex A (informative) Useful contacts

19、 41 A.1 World Intellectual Property Organization (WIPO) 41 A.1.1 General . 41 A.1.2 What is WIPO? 41 A.1.3 WIPO Intellectual Property Services . 41 A.1.4 WIPO global network on Intellectual Property (IP) Academies . 43 A.2 Anti-Counterfeiting Trade Agreement (ACTA) . 43 PD IEC/TS 62668-1:2016 4 IEC

20、TS 62668-1:2016 IEC 2016 A.2.1 ACTA . 43 A.2.2 Global Anti-Counterfeiting Network (GACG) 44 A.3 World Semiconductor Council (WSC) . 44 A.4 SEMI 44 A.5 Electronics Authorized Directory 46 A.6 UK 46 A.6.1 The UK intellectual property office 46 A.6.2 Alliance for IP 46 A.6.3 UK Chartered Trading Standa

21、rds Institute . 47 A.6.4 UK HM Revenue and Customs . 47 A.6.5 ESCO Anti-counterfeiting Forum (formerly UKEA Anti-Counterfeiting Forum) . 47 A.6.6 Electronic Component Supplier Network (ESCN). 47 A.6.7 UK Ministry of Defence . 48 A.7 Europe 48 A.7.1 Europa Summaries of EU Legislation 48 A.7.2 Europol

22、, the European Law Enforcement Agency 48 A.7.3 European Patent Office 48 A.7.4 Europe at OHIM . 48 A.7.5 European Aviation Safety Agency (EASA) 49 A.7.6 IECQ audit schemes 49 A.7.7 BEAMA 50 A.8 USA 50 A.8.1 United States Patent and Trademark Office 50 A.8.2 The International Trade Administration, US

23、 Department of Commerce . 50 A.8.3 US Embassy in China information . 51 A.8.4 International Intellectual Property Alliance 51 A.8.5 The Federal Aviation Administration (FAA) . 52 A.8.6 Trusted Access Program Office (TAPO) 52 A.8.7 Defense Microelectronics Activity (DMEA) 53 A.8.8 Independent Distrib

24、utors of Electronics Association (IDEA) . 53 A.8.9 ECIA formerly National Electronic Distributors Association (NEDA) . 54 A.8.10 Components Technology Institute Inc. (CTI) . 55 A.8.11 Defense Logistics Agency (DLA) 55 A.8.12 DFARS 55 A.8.13 IAQG . 55 A.9 China 56 A.9.1 State Intellectual Property of

25、fice of the P.R.C. 56 A.9.2 Chinese Patent and Trademark Office 56 A.9.3 China Electronics Associations: 56 A.9.4 China Electronics Quality Management Association (CQAE) . 56 A.9.5 Chinalawinfo.Co Ltd., for Law info China 56 A.10 Japan Japanese Patent Office (JPO) 56 A.11 Physical unclonable functio

26、n . 56 A.12 The Hardware Intrinsic Security (HIS) initiative 57 A.13 Examples of tamper-proof design companies . 58 A.14 Examples of FPGA die serialization . 58 A.15 Examples of NVRAM manufacturers 58 A.16 SAE G-19 . 58 PD IEC/TS 62668-1:2016IEC TS 62668-1:2016 IEC 2016 5 A.17 iNEMI . 60 A.18 OECD .

27、 61 A.19 ICC . 61 A.20 Applied DNA Sciences 61 Annex B (informative) Examples of aftermarket sources 62 B.1 Examples of franchised aftermarket sources 62 B.2 Examples of sources of franchised die which can be packaged 62 B.3 Examples of third party custom packaging houses which provide aftermarket s

28、olutions . 62 B.4 Examples of emulated aftermarket providers 63 Annex C (informative) Typical example of a RECS certificate 64 Annex D (informative) Flowchart of IEC TS 62668-1 requirements 65 Bibliography . 67 Figure 1 Suspect components perimeter . 20 Table 1 Anti-counterfeit awareness training gu

29、idelines 17 Table 2 IEC TS 62668-1 requirements waived if OEM has an approved SAE AS5553A plan . 36 PD IEC/TS 62668-1:2016 6 IEC TS 62668-1:2016 IEC 2016 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ PROCESS MANAGEMENT FOR AVIONICS COUNTERFEIT PREVENTION Part 1: Avoiding the use of counterfeit, fraudu

30、lent and recycled electronic components FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all que

31、stions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publicatio

32、n(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC col

33、laborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion

34、 on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensu

35、re that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to

36、 the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certificatio

37、n bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall atta

38、ch to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees

39、) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publicatio

40、n. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. The main task of IEC technical committees is to prepare International Standards. In exce

41、ptional circumstances, a technical committee may propose the publication of a technical specification when the required support cannot be obtained for the publication of an International Standard, despite repeated efforts, or the subject is still under technical development or where, for any other r

42、eason, there is the future but no immediate possibility of an agreement on an International Standard. Technical specifications are subject to review within three years of publication to decide whether they can be transformed into International Standards. IEC TS 62668-1, which is a technical specific

43、ation, has been prepared by IEC technical committee 107: Process management for avionics. PD IEC/TS 62668-1:2016IEC TS 62668-1:2016 IEC 2016 7 This third edition cancels and replaces the second edition, published in 2014. This edition constitutes a technical revision. This edition includes the follo

44、wing significant technical changes with respect to the previous edition: a) identified that the Chinese RECS scheme is no longer maintained (in 4.2 and where appropriate as agreed with CEPREI); b) added a reference to AS/EN/JISQ 9100 which at the next revision (revision D) will contain an anti-count

45、erfeit requirement which may be used to satisfy the requirements of 4.2; c) added reference to the now published SAE AS6496 for franchised distributors, to USA DFARS rule 252.246.7007 and to UK Defence Standard 05-135; d) added reference to more GAO, OECD and ICC reports in 4.5.1; e) updated weblink

46、s and other references. The text of this technical specification is based on the following documents: Enquiry draft Report on voting 107/267/DTS 107/277/RVC Full information on the voting for the approval of this technical specification can be found in the report on voting indicated in the above tab

47、le. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all the parts in the IEC 62668 series, published under the general title Process management for avionics Counterfeit prevention, can be found on the IEC website. The committee has decided that the cont

48、ents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be transformed into an International standard, reconfirmed, withdrawn, replaced by a

49、revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. PD IEC/TS 62668-1:2016 8 IEC TS 62668-1:2016 IEC 2016 PROCESS MANAGEMENT FOR AVIONICS COUNTERFEIT PREVENTION Part 1: Avoiding the use of co