BS PD IEC TS 62564-1-2016 Process management for avionics Aerospace qualified electronic components (AQEC) Integrated circuits and discrete semiconductors《航空电子设备的过程管理 航空航天用合格电子设备(A.pdf

《BS PD IEC TS 62564-1-2016 Process management for avionics Aerospace qualified electronic components (AQEC) Integrated circuits and discrete semiconductors《航空电子设备的过程管理 航空航天用合格电子设备(A.pdf》由会员分享，可在线阅读，更多相关《BS PD IEC TS 62564-1-2016 Process management for avionics Aerospace qualified electronic components (AQEC) Integrated circuits and discrete semiconductors《航空电子设备的过程管理 航空航天用合格电子设备(A.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、Process management for avionics Aerospace qualifiedelectronic components (AQEC)Part 1: Integrated circuits and discrete semiconductorsPD IEC/TS 62564-1:2016BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis Published Document is the UK implementati

2、on of IEC/TS 62564-1:2016.It supersedes DD IEC/TS 62564-1:2011 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee GEL/107, Process management for avionics.A list of organizations represented on this committee can be obtained onrequest to its secretary.This

3、 publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 93071 3ICS 03.100.50; 31.020; 49.060Compliance with a British Standard c

4、annot confer immunity fromlegal obligations.This Published Document was published under the authority of theStandards Policy and Strategy Committee on 31 July 2016.Amendments/corrigenda issued since publicationDate Text affectedPUBLISHED DOCUMENTPD IEC/TS 62564-1:2016IEC TS 62564-1 Edition 3.0 2016-

5、07 TECHNICAL SPECIFICATION Process management for avionics Aerospace qualified electronic components (AQEC) Part 1: Integrated circuits and discrete semiconductors INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 03.100.50; 31.020; 49.060 ISBN 978-2-8322-3513-3 Registered trademark of the International

6、 Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. PD IEC/TS 62564-1:2016 2 IEC TS 62564-1:2016 IEC 2016 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references. 6 3 Terms, definitions and abbreviations 7 3.1 Terms and d

7、efinitions 7 3.2 Abbreviations 9 4 Technical requirements 9 4.1 AQEC plan 9 4.2 AQEC documentation 10 4.2.1 General . 10 4.2.2 AQEC data sheet . 10 4.2.3 Material content . 10 4.2.4 AQEC visibility . 10 4.2.5 AQEC life expectancy 10 4.2.6 Device technology 11 4.2.7 SEE data . 11 4.2.8 Termination fi

8、nish 11 4.2.9 Third party part numbers 11 4.3 AQEC performance . 12 4.3.1 Performance 12 4.3.2 Functional parameters 13 4.3.3 Known limitations . 13 4.4 Quality system certification 13 4.5 Component qualification and re-qualification 13 4.6 AQEC quality assurance and reliability monitoring . 13 4.7

9、Product change notification (PCN) . 14 4.8 Last time buy (LTB) notification . 14 4.9 Obsolescence management . 14 4.10 Counterfeit prevention . 14 4.11 User or customer guide . 14 Annex A (informative) AQEC material content and construction table 15 Annex B (informative) Additional desired data 17 B

10、ibliography . 18 Table A.1 AQEC material content and construction . 15 PD IEC/TS 62564-1:2016IEC TS 62564-1:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ PROCESS MANAGEMENT FOR AVIONICS AEROSPACE QUALIFIED ELECTRONIC COMPONENTS (AQEC) Part 1: Integrated circuits and discrete semiconduc

11、tors FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization i

12、n the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrus

13、ted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the Internat

14、ional Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since eac

15、h technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IE

16、C Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in the

17、ir national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessm

18、ent services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employe

19、es, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the p

20、ublication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the pos

21、sibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. The main task of IEC technical committees is to prepare International Standards. In exceptional circumstances, a technical

22、committee may propose the publication of a technical specification when the required support cannot be obtained for the publication of an International Standard, despite repeated efforts, or the subject is still under technical development or where, for any other reason, there is the future but no i

23、mmediate possibility of an agreement on an International Standard. Technical specifications are subject to review within three years of publication to decide whether they can be transformed into International Standards. IEC TS 62564-1, which is a technical specification, has been prepared by IEC tec

24、hnical committee 107: Process management for avionics. PD IEC/TS 62564-1:2016 4 IEC TS 62564-1:2016 IEC 2016 This third edition cancels and replaces the second edition, published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes

25、 with respect to the previous edition: a) IEC TS 62239 changed to IEC TS 62239-1, and IEC PAS 62686-1 changed to IEC TS 62686-1; b) JESD48 changed to J-STD-048 and added to the Bibliography; c) AEC-Q100 revision G changed to AEC-Q100:2014 in 4.5 (which is now revision H); d) revision of AEC-Q101 rem

26、oved in Bibliography; e) J-STD-609 for “Marking and labelling” added to the Bibliography; f) information added regarding components life expectancy in 4.2.5. GEIA-STD-0002-001 (June 2006), Aerospace Qualified Electronic Component (AQEC) Requirements, Volume 1 Integrated Circuits and Semiconductors,

27、has served as a basis for the elaboration of this technical specification. The text of this technical specification is based on the following documents: Enquiry draft Report on voting 107/276/DTS 107/283/RVC Full information on the voting for the approval of this technical specification can be found

28、 in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62564 series, under the general title Process management for avionics Aerospace qualified electronic components (AQEC), can be fo

29、und on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be transformed into an

30、 International standard, reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. PD IEC/TS 62564-1:2016IEC TS 62564-1:2016 IEC 2016 5 INTRODUCTION Aerospace qualified electronic components (AQEC) plans are developed by

31、 manufacturers in order to document compliance with AQEC requirements. For AQEC designated components, the intention is to a) provide AQEC users access to information from the AQEC manufacturers that is necessary for using commercial-off-the-shelf (COTS) products; b) better enable AQEC users to asse

32、ss whether these parts are capable of operating reliably in their applications; c) minimize deviations from the AQEC manufacturers COTS products; d) have minimal impact on the AQEC manufacturers standard operating or business procedures; e) promote communication between the AQEC manufacturers and us

33、ers. PD IEC/TS 62564-1:2016 6 IEC TS 62564-1:2016 IEC 2016 PROCESS MANAGEMENT FOR AVIONICS AEROSPACE QUALIFIED ELECTRONIC COMPONENTS (AQEC) Part 1: Integrated circuits and discrete semiconductors 1 Scope This part of IEC 62564, which is a Technical Specification, defines the minimum requirements for

34、 integrated circuits and semiconductors which are designated as an “aerospace qualified electronic component (AQEC)”. It applies to integrated circuits and semiconductors exhibiting the following attributes: a) a minimum set of requirements, or information provided by the part manufacturer, which wi

35、ll allow a standard COTS component to be designated AQEC by the manufacturer; b) as a minimum, each COTS component (designated AQEC) will have been designed, fabricated, assembled, and tested in accordance with the component manufacturers requirements for standard data book components; c) qualificat

36、ion of, and quality systems for, the COTS components to be designated as AQEC should include the manufacturers standards, operating procedures, and technical specifications. This information should be available when requested; d) components manufactured before the manufacturer has addressed AQEC req

37、uirements, but utilizing the same processes, are also considered AQEC compliant; e) additional desired attributes of a device designated AQEC (that will support AQEC users) are found in Annex B of this technical specification. NOTE Parts qualified to military specifications (except those identified

38、as being for “logistic support” purposes only) are considered AQEC; the remainder of this technical specification only addresses non-military specification parts. Parts qualified to AEC-Q100, grade 0 through to grade 3 are considered AQEC. For those applications where a 0 C to +70 C temperature rang

39、e is appropriate, grade 4 is also considered to be AQEC. The users should document that the grade category used is compatible with the application in accordance with their IEC TS 62239-1 electronic components management plan (ECMP). 2 Normative references The following documents are referred to in t

40、he text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC TS 62239-1, Process management for av

41、ionics Management plan Part 1: Preparation and maintenance of an electronic components management plan IEC 62396-1, Process management for avionics Atmospheric radiation effects Part 1: Accommodation of atmospheric radiation effects via single event effects within avionics electronic equipment IEC T

42、S 62668-1, Process management for avionics Counterfeit prevention Part 1: Avoiding the use of counterfeit, fraudulent and recycled electronic components ISO 9001, Quality management systems Requirements PD IEC/TS 62564-1:2016IEC TS 62564-1:2016 IEC 2016 7 J-STD-048, Notification Standard for Product

43、 Discontinuance 3 Terms, definitions and abbreviations For the purposes of this document, the following terms, definitions and abbreviations apply. 3.1 Terms and definitions 3.1.1 AQEC specification document prepared by or for the manufacturer to describe an AQEC product Note 1 to entry: It includes

44、 a data sheet and may include other documents, such as material descriptions, environmental test procedures, quality monitoring processes, etc. It may be a stand-alone document or a clearly denoted item within a larger documentation system. There may be additional data associated with specific appli

45、cations which may be requested separately. 3.1.2 AQEC plan instrument prepared by the plan owner (see 3.1.10) that clearly, concisely, and unambiguously documents the processes used by the plan owner to satisfy the requirements of this technical specification Note 1 to entry: The plan contains audit

46、able content. 3.1.3 assessment evaluation of a plan owners AQEC plan to determine if it is compliant with this technical specification Note 1 to entry: It may be conducted by IECQ, the customer, the customers designee, or by a third party designated by the customer community. 3.1.4 microcircuit inte

47、grated circuit microcircuit (device with a high circuit-element density) in which all or some of the circuit elements are inseparably associated and electrically interconnected (on one or more substrates, in a unique indivisible package) so that the microcircuit is considered to be indivisible for t

48、he purpose of construction and commerce 3.1.5 semiconductor discrete semiconductor device semiconductor device that is specified to perform an elementary function and that is not divisible into separate components functional in themselves (for example diodes, transistors, optocouplers, LEDs and rela

49、ted products) 3.1.6 component part microcircuit, integrated circuit, semiconductor or discrete semiconductor for the purpose of this specification PD IEC/TS 62564-1:2016 8 IEC TS 62564-1:2016 IEC 2016 3.1.7 customer user designer original equipment manufacturer (OEM) that procures integrated circuits and/or semiconductor devices compliant with this technical specification and uses them to design, produce, and maintain systems 3.1.8 customer community body of customers tha