BS PD IEC TS 60034-2-3-2013 Rotating electrical machines Specific test methods for determining losses and efficiency of converter-fed AC induction motors《旋转电机 测定变频器馈电的交流感应电动机的损失和效率.pdf

《BS PD IEC TS 60034-2-3-2013 Rotating electrical machines Specific test methods for determining losses and efficiency of converter-fed AC induction motors《旋转电机 测定变频器馈电的交流感应电动机的损失和效率.pdf》由会员分享，可在线阅读，更多相关《BS PD IEC TS 60034-2-3-2013 Rotating electrical machines Specific test methods for determining losses and efficiency of converter-fed AC induction motors《旋转电机 测定变频器馈电的交流感应电动机的损失和效率.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationRotating electrical machinesPart 2-3: Specific test methods for determining losses and efficiency of converter-fed AC induction motorsPD IEC/TS 60034-2-3:2013Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo r

2、eproduction or networking permitted without license from IHS-,-,-National forewordThis Published Document is the UK implementation of IEC/TS 60034-2-3:2013.The UK participation in its preparation was entrusted to TechnicalCommittee PEL/2, Rotating electrical machinery.A list of organizations represe

3、nted on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 69

4、043 3ICS 29.160Compliance with a British Standard cannot confer immunity fromlegal obligations.This Published Document was published under the authority of theStandards Policy and Strategy Committee on 28 February 2014.Amendments/corrigenda issued since publicationDate Text affectedPUBLISHED DOCUMEN

5、TPD IEC/TS 60034-2-3:2013Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-IEC/TS 60034-2-3 Edition 1.0 2013-11 TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE Rotating

6、electrical machines Part 2-3: Specific test methods for determining losses and efficiency of converter-fed AC induction motors Machines lectriques tournantes Partie 2-3: Mthodes dessai spcifiques pour la dtermination des pertes et du rendement des moteurs induction en courant alternatif aliments par

7、 convertisseur INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE S ICS 29.160 PRICE CODE CODE PRIX ISBN 978-2-8322-1275-2 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Ma

8、ke sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colourinsidePD IEC/TS 60034-2-3:2013Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolle

9、d Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- 2 TS 60034-2-3 IEC:2013 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 7 2 Normative references 7 3 Terms and definitions 7 4 Symbols and abbreviated terms . 8 5 Basic requirements 9 5.1 Instrumentation 9 5.1.

10、1 General 9 5.1.2 Power analyzer and transducers . 9 5.1.3 Mechanical output of the motor . 10 5.2 Converter set up 10 5.2.1 General 10 5.2.2 Test converter set up for rated voltages up to 1 kV . 10 5.2.3 Testing with the converter for the final application 11 6 Test methods for the determination of

11、 the efficiency of converter-fed motors . 11 6.1 Test method (see Table 1) . 11 6.2 Method 2-3-A: Summation of losses with test converter supply 11 6.2.1 General 11 6.2.2 Test procedure . 12 6.2.3 Efficiency determination 13 6.3 Method 2-3-B: Summation of losses with specific converter supply 14 6.4

12、 Method 2-3-C: Input-output method 14 6.4.1 Test set-up . 14 6.4.2 Test procedure . 14 6.4.3 Efficiency determination 14 6.5 Method 2-3-D: Calorimetric method 14 7 Other procedures . 14 Annex A (informative) Definition of the output voltage of the test converter 15 A.1 Definitions and schematic 15 A

13、.2 Voltage reference and generation of output voltage waveform . 16 A.3 Checking in the time domain 19 Bibliography 21 Figure A.1 Schematic for PDS 15 Figure A.2 Functional schematic for voltage generation system . 17 Figure A.3 Sinusoidal voltage set point and linearity extension voltage 17 Figure

14、A.4 Voltage set point and extended reference voltage . 18 Figure A.5 Pulse pattern of motor terminal voltage (fundamental frequency 50 Hz; switching triangle frequency 4 kHz) . 18 Figure A.6 Magnification of marked area of Figure A.5 . 19 Figure A.7 Filtered inverter terminal voltage (fundamental fr

15、equency of 50 Hz; 2ndorder low pass filter 500 Hz / 0,7) . 19 Table 1 Testing methods 11 PD IEC/TS 60034-2-3:2013Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-TS 60

16、034-2-3 IEC:2013 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ROTATING ELECTRICAL MACHINES Part 2-3: Specific test methods for determining losses and efficiency of converter-fed AC induction motors FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for stand

17、ardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes Int

18、ernational Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participa

19、te in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between

20、 the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications

21、have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any m

22、isinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding na

23、tional or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any service

24、s carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC Nation

25、al Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is

26、drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall

27、not be held responsible for identifying any or all such patent rights. The main task of IEC technical committees is to prepare International Standards. In exceptional circumstances, a technical committee may propose the publication of a technical specification when the required support cannot be obt

28、ained for the publication of an International Standard, despite repeated efforts, or the subject is still under technical development or where, for any other reason, there is the future but no immediate possibility of an agreement on an International Standard. Technical specifications are subject to

29、 review within three years of publication to decide whether they can be transformed into International Standards. IEC/TS 60034-2-3, which is a technical specification, has been prepared by IEC technical committee 2: Rotating machinery. PD IEC/TS 60034-2-3:2013Copyright British Standards Institution

30、Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- 4 TS 60034-2-3 IEC:2013 The text of this technical specification is based on the following documents: Enquiry draft Report on voting 2/1696/DTS 2/1719/RVC Fu

31、ll information on the voting for the approval of this technical specification can be found in the report on voting indicated in the above table. NOTE A table of cross-references of all IEC TC 2 publications can be found on the IEC TC 2 dashboard on the IEC website. This publication has been drafted

32、in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication

33、 will be transformed into an International standard, reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its con

34、tents. Users should therefore print this document using a colour printer. PD IEC/TS 60034-2-3:2013Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-TS 60034-2-3 IEC:201

35、3 5 INTRODUCTION The objective of this technical specification is to define test methods for determining the additional harmonic motor losses of converter-fed induction motors. These losses appear in addition to the losses on nominally sinusoidal power supply as determined by the methods of IEC 6003

36、4-2-1. Results determined according to this specification are intended to allow for comparison of the harmonic losses of different AC induction motors when fed by converters. In power-drive systems (PDS), the motor and the frequency converter are often manufactured by different suppliers. While moto

37、rs of the same design are produced in large quantities, they may be operated from the grid or from frequency converters of many different types, supplied by many different manufacturers. The individual converter properties (switching frequency, DC link voltage level, etc.) may influence the system e

38、fficiency as well. It is impractical to determine the additional harmonic motor losses for every combination of motor, frequency converter, connection cable, output filter and parameter settings. Accepting that it is extremely difficult to specify motor efficiency for converter operation, this speci

39、fication describes a limited number of approaches, depending on the voltage level and the rating of the machine under test. The procedures described in this specification result in a single number, the harmonic loss ratio rHL, which is the ratio of the additional harmonic motor losses and the motor

40、losses measured using a nominally sinusoidal voltage power supply. The losses determined according to this specification are not intended to represent the losses in the final application. They provide, however, an objective basis for comparing different motor designs with respect to suitability for

41、converter operation. The methods in this technical specification apply to induction motors used with variable frequency drives. However, the application to other AC motors or DC motors and converters, is not excluded. The methods are mainly intended for motors fed by voltage source converters. In ge

42、neral, when fed from a converter, the motor losses are higher than during operation on a nominally sinusoidal system. The additional harmonic losses depend on the spectrum of the impressed converter output quantity (either current or voltage) which is influenced by its circuitry and control method.

43、For further information see IEC/TS 60034-25. This technical specification is aimed at evaluating the additional harmonic motor losses resulting from non-sinusoidal power supply and consequently the efficiency of the converter-fed motor. It is not the purpose of this technical specification to define

44、 test procedures either for power drive systems or for frequency converters alone. This technical specification is applicable to motors rated for 50 Hz or 60 Hz fundamental frequency. However, for other rated motor frequencies the test procedure may be applied provided a suitable power source is ava

45、ilable, e.g. a 4-pole motor used at 3 000 rpm can be tested with 100 Hz and actual voltage rating. Low-voltage motors Experience has shown that the additional harmonic motor losses generally increase with load. The methods in this technical specification are based on supplies from converters with pu

46、lse width modulation (PWM) and constant pulse pattern. This is generally the case for voltage source converters except for over-modulation. Such voltage source converters have by far the largest market share in the low-voltage industrial drive market. With respect to these types of converters and th

47、e growing need for verification of compliance with national energy efficiency regulations, this technical specification introduces a so-called test converter for testing low voltage motors. PD IEC/TS 60034-2-3:2013Copyright British Standards Institution Provided by IHS under license with BSI - Uncon

48、trolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- 6 TS 60034-2-3 IEC:2013 In principle, the test converter is a voltage source with a clearly defined and reproducible harmonic content to supply the machine under test. The motor efficiency is to be determined at rated load for 50 Hz or 60 Hz. Defining 50 Hz or 60 Hz as test conditions has the advantage of providing a direct comparison of motor efficiency for grid and converter operation. The above outlined test converter concept is a new approach to weigh the converter impact on an electric